scholarly journals Semi-Large Scale Experiments Performed on Specimens With Underclad Cracks

2008 ◽  
Author(s):  
Vladislav Pistora ◽  
Milan Brumovsky
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Failure Process ◽  
Base Material ◽  
Video Camera ◽  
Pressure Vessels ◽  
Ductile Tearing ◽  
Four Point Bending ◽  
High Speed Video Camera ◽  
Reactor Pressure

During years 2005–2006, a series of semi-large scale experiments on specimens containing underclad (embedded) crack were performed in NRI Rez. The experiments were performed within EU PHARE project EUROPAID/116529/D/SV/CZ, in cooperation with VTT, FNS, TVONS (Finland) and Tecnatom (Spain). The aim of the project was to investigate fracture mechanics properties of cladding, in particular, to establish the role of cladding in the fracture/failure process of the specimen, and based on obtained results to improve the current procedure for evaluation of integrity of WWER reactor pressure vessels. The specimens were manufactured from artificially aged material of decommissioned (not operated) reactor pressure vessel of WWER 440 Type NPP. Each of the specimens contained through-thickness crack embedded in the base material (with approx. 3 mm ligament separating the upper crack front from cladding), and was loaded by four-point-bending loading at room temperature. During loading, majority of specimens exhibited pop-ins followed by ductile tearing of cladding and final failure; only 3 specimens fractured through suddenly, without preceding pop-ins. Evaluation of the experiments concentrated on both process of cleavage fracture in base material and process of ductile tearing in cladding. In the presented paper, the results of experiments are in detail described, including photos from the experiments and photos taken with using high-speed video camera during some of experiments.

Experimental Verification of the Behavior of Underclad Cracks Using Semi-Large Scale Specimens

2008 ◽  
Author(s):  
Vladislav Pisˇtora ◽  
Milan Brumovsky´ ◽  
Dana Lauerova´
Keyword(s):  
Large Scale ◽  
Failure Process ◽  
Base Material ◽  
Pressure Vessels ◽  
Aged Material ◽  
Ductile Tearing ◽  
Four Point Bending ◽  
Final Failure ◽  
Embedded Crack

During years 2005–2006 a series of semi-large scale experiments of specimens containing underclad (embedded) crack were performed in NRI Rez. The experiments were performed within EU PHARE project in cooperation with VTT, FNS, TVONS (Finland) and Tecnatom (Spain). The aim of the project was to investigate fracture mechanics properties of cladding in particular to establish the role of cladding in fracture failure process of the specimens, and to exploit the obtained knowledge in the procedure for evaluation of integrity of WWER reactor pressure vessels. The specimens were manufactured from an artificially aged material of decommissioned (not operated) RPV of WWER-440 type. Each of specimens contained through-thickness crack embedded in the base material and was loaded by four-point-bending (4PB) loading. During loading, majority of specimens exhibited pop-ins followed by ductile tearing of cladding and final failure. Evaluation of the experiments concentrated on both process of cleavage fracture in base material and process of ductile tearing in cladding. In the presented paper, the results of experiments are described in detail. New proposal for procedure of assessment of RPV integrity, based on the PHARE project, was prepared and will be presented in a separate paper.

Packets of Capillary and Acoustic Waves of Drop Impact

2021 ◽  
pp. 73-91
Author(s):  
Yu.D. Chashechkin
Keyword(s):  
Acoustic Waves ◽  
High Speed ◽  
Large Scale ◽  
Video Camera ◽  
Acoustic Signals ◽  
Capillary Waves ◽  
Near Surface ◽  
Large Scale Analysis ◽  
High Speed Video Camera ◽  
Hydro Phone

Flows, capillary waves, and acoustic signals generated by a drop of water falling into a pool of degassed liquid were recorded by a high-speed video camera, hydro-phone, and microphone. A large-scale analysis of the system of equations was performed. The fast conversion of available surface potential energy is traced. The converted energy is stored in a thin layer in the vicinity of the merged free surfaces and creates large perturbations of temperature, pressure and flow velocity. Capillary waves start to radiate simultaneously with the formation of a cavity and the rise of the crown. New groups of capillary waves arise with all changes in the flow structure --- the formation and immersion of a splash, come back of secondary drops, the formation of cavities, the immersion of a streamer and droplets. Simultaneously with the waves, ligaments --- thin near-surface flows are formed that affect the transport and rupture of gas cavities. Thin flows quickly decay and form again when a new group of capillary waves is generated. A comparison of flow patterns and acoustic signals indicates that the generation of resonant sound packets is synchronized with the pinch-off gas fragments from the cavity or their breaking. The duration of the sound depends on the initial heterogeneity of the geometry of the sounding cavity, gradually transforming into a smooth spheroidal form

scholarly journals Detonation effects of shallow buried explosive in sandy soil on target plate acceleration in a small-scale blast test

2018 ◽  
Vol 192 ◽  
pp. 02028
Author(s):  
Hassan Zulkifli Abu ◽  
Ibrahim Aniza ◽  
Mohamad Nor Norazman
Keyword(s):  
Sandy Soil ◽  
High Speed ◽  
Early Stage ◽  
Time History ◽  
Video Camera ◽  
Small Scale ◽  
Target Plate ◽  
Air Blast ◽  
High Speed Video Camera ◽  
The Impact

Small-scale blast tests were carried out to observe and measure the influence of sandy soil towards explosive blast intensity. The tests were to simulate blast impact imparted by anti-vehicular landmine to a lightweight armoured vehicle (LAV). Time of occurrence of the three phases of detonation phase in soil with respect to upward translation time of the test apparatus were recorded using high-speed video camera. At the same time the target plate acceleration was measured using shock accelerometer. It was observed that target plate deformation took place at early stage of the detonation phase before the apparatus moved vertically upwards. Previous data of acceleration-time history and velocity-time history from air blast detonation were compared. It was observed that effects of soil funnelling on blast wave together with the impact from soil ejecta may have contributed to higher blast intensity that characterized detonation in soil, where detonation in soil demonstrated higher plate velocity compared to what occurred in air blast detonation.

In Situ Observation Method for Quantitative Evaluation of Solidification Phenomena and Solidification Cracks during Welding

2014 ◽  
Vol 782 ◽  
pp. 3-7
Author(s):  
Kenji Shinozaki ◽  
Motomichi Yamamoto ◽  
Kohta Kadoi ◽  
Peng Wen
Keyword(s):  
High Speed ◽  
Video Camera ◽  
Solidification Cracking ◽  
In Situ Observation ◽  
High Speed Video Camera ◽  
Varestraint Test ◽  
Solidification Cracks ◽  
Observation Method ◽  
Solidification Crack

Solidification cracking during welding is very serious problem for practical use. Therefore, there are so many reports concerning solidification cracking. Normally, solidification cracking susceptibility of material is quantitatively evaluated using Trans-Varestraint test. On the other hand, local solidification cracking strain was tried to measure precisely using in-situ observation method, called MISO method about 30 years ago. Recently, digital high-speed video camera develops very fast and its image quality is very high. Therefore, we have started to observe solidification crack using in site observation method. In this paper, the local critical strain of a solidification crack was measured and the high temperature ductility curves of weld metals having different dilution ratios and different grain sizes to evaluate quantitatively the effects of dilution ratio and grain size on solidification cracking susceptibility by using an improved in situ observation method.

Study on Magnetic Barrel Machine Equipped with Three-Dimensional Arrangement of Magnets

2007 ◽  
Vol 329 ◽  
pp. 761-766 ◽  
Author(s):  
Y. Zhang ◽  
Masato Yoshioka ◽  
Shin-Ichiro Hira
Keyword(s):  
High Speed ◽  
Permanent Magnets ◽  
Three Dimensional ◽  
Video Camera ◽  
High Speed Video ◽  
High Speed Video Camera ◽  
The Media ◽  
Set Up

At present, a commercially available magnetic barrel machine equipped with permanent magnets has some faults arising from constructional reason. That is, grinding or finishing ability is different from place to place in the machining region, resulting in the limitation on the region we can use in the container of workpieces. Therefore, in this research, authors made the new magnetic barrel machine equipped with three dimensional (3D) magnet arrangement to overcome these faults. The grinding ability of the new 3D magnetic barrel machine converted was experimentally examined, and compared with that of the traditional magnetic barrel machine. As a result, it was shown that we can use much broader region in the new 3D machine. It was also shown that the grinding ability became higher. The distribution of barrel media in action was recorded by means of a high speed video camera. It was clarified that the media rose up higher and were distributed more uniformly in the container by the effect of the magnet block newly set up. It was supposed that this must be the reason for the above-mentioned improvement of grinding ability.

Grease soap particles passing through an elastohydrodynamic contact under side slip conditions

2000 ◽  
Vol 214 (4) ◽  
pp. 317-325 ◽  
Author(s):  
P Eriksson ◽  
V Wikström ◽  
R Larsson
Keyword(s):  
Film Thickness ◽  
High Speed ◽  
Previous Investigation ◽  
Video Camera ◽  
Slip Conditions ◽  
High Speed Video ◽  
Elastohydrodynamic Contact ◽  
High Speed Video Camera ◽  
Pure Rolling ◽  
Minimum Film Thickness

In a previous investigation, grease thickener fibres were tracked as they passed through an elastohydrodynamic (EHD) contact in pure rolling using interferometry in a standard ball-and-disc apparatus. In order to capture single thickener fibres, a high-speed video camera was used. Here, the experiments have been repeated introducing different amounts of side slip for different rolling speeds and a faster video camera capable of capturing 4500 frames/s. The contact was lubricated with a continuous supply of grease. Two greases, based on the same synthetic poly(α-olefin) but thickened with Li-12-OH and lithium complex soap respectively, were studied. It was observed that the thickener fibres were stretched both before entering the contact and as they passed through it. Fibres seem to avoid the minimum film thickness regions and, if they enter, the film is restored immediately after passage.

Biomechanical Analysis of a World Record Javelin Throw: A Case Study

1985 ◽  
Vol 1 (1) ◽  
pp. 73-77 ◽  
Author(s):  
Robert J. Gregor ◽  
Marilyn Pink
Keyword(s):  
High Speed ◽  
Video Camera ◽  
The United States ◽  
Track And Field ◽  
Biomechanical Analysis ◽  
World Record ◽  
High Speed Video ◽  
High Speed Video Camera ◽  
Ongoing Project

As part of an ongoing project to evaluate elite track and field throwers in the United States, the javelin competition was filmed during the 1983 Pepsi Invitational Track Meet. A high-speed video camera (Spin Physics SP2000) was positioned orthogonal to the javelin runway to record the release of all throws. During this competition, Tom Petranoff’s world record (99.72 m) was filmed at 200 fields per second. Subsequent frame-by-frame digitization yielded results consistent with reports in the literature. Release velocity was 32.3 m/s and represents one of the highest values ever reported. Angle of release was .57r, javelin attitude at release was .64r» and angle of attack was .07r. While optimum values for these release parameters, in light of published results, remain open to discussion, the results presented here represent unique information on a world record performance and can serve as a basis of comparison for future performances.

Liquid Sheet Disintegration and Atomization Process on a Simplified Airblast Atomizer

1993 ◽  
Vol 115 (3) ◽  
pp. 461-466 ◽  
Author(s):  
G. Lavergne ◽  
P. Trichet ◽  
P. Hebrard ◽  
Y. Biscos
Keyword(s):  
High Speed ◽  
Swirling Flow ◽  
Video Camera ◽  
Frequency Instability ◽  
Liquid Sheet ◽  
Processing Unit ◽  
Spray Formation ◽  
High Speed Video Camera ◽  
The Mean ◽  
Component Phase

Liquid sheet break-up in coflowing shear flow is the mean by which liquids are atomized in practical injectors for gas turbine combustors. The present study explores experimentally the mechanisms of liquid sheet instabilities and spray formation. Experiments are conducted on four airblast geometries. A high-speed video camera associated with an image processing unit was used to study the liquid sheet instabilities. A microphone and a frequency analyzer were used to track the disintegration frequency. Instability amplitude and disintegration length of the liquid sheet were measured. A two-component Phase Doppler Particle Analyzer was used to characterize the resultant spray. The spatial distribution of the particle size is influenced by the swirling flow field. These experimental results will be used to assess models of fuel sheet instabilities and disintegration.

Sign in / Sign up

Export Citation Format

Share Document