Experimental Investigation and Finite Element Analysis on Cold-Stretching for Austenitic Stainless Pressure Vessels

2017 ◽  
Author(s):  
Yu Han ◽  
Kesheng Wang
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Measurement Range ◽  
Pressure Vessels ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Complex Deformation ◽  
Whole Process ◽  
Current Criterion ◽  
Stretching Process

Cold-stretching is an effective way to make the pressure vessels lighter. A test vessel with austenitic stainless steel was designed and manufactured based on the current criterion, and the cold-stretching process was carried out. The deformation of each part of the vessel under the pressure of each stage were measured by the resistance strain gauge in its measurement range. The finite element method is used to calculate the deformation trend of the whole process of cold-stretching. In addition, the strain of complex deformation at nozzle and its surrounding was analyzed by FEM.

FFS Assessment of Pressurized Equipment Utilizing a Thickness Mapping Tool

2016 ◽  
Author(s):  
Benjamin Hantz ◽  
Venkata M. K. Akula ◽  
John Leroux
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Response Prediction ◽  
Accurate Estimate ◽  
Pressure Vessels ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Level 3 ◽  
Level 1 ◽  
Element Method

For pressure vessels, loss of thickness detected during scheduled maintenance utilizing UT scans can be assessed based on Level 1 or 2 analyses as per API 579 guidelines. However, Level 1 and 2 analyses can point to excessively conservative assessments. Level – 3 assessments utilizing the finite element method can be performed for a more accurate estimate of the load carrying capacity of the corroded structure. However, for a high fidelity structural response prediction using the finite element method, the characteristics of the model must be accurately represented. Although the three nonlinearities, namely, the geometric, material, and contact nonlinearities can be adequately included in a finite element analysis, procedures to accurately include the thickness measurements are not readily available. In this paper, a tool to map thicknesses obtained from UT scans onto a shell based finite element models, to perform Level – 3 analyses is discussed. The tool works in conjunction with Abaqus/CAE and is illustrated for two different structures following the elastic-plastic analysis procedure outlined in the API 579 document. The tool is intended only as a means to reduce the modeling time associated with mapping thicknesses. The results of the analyses and insights gained are presented.

Contact Between Vessel Shell and Welded Pad in Nozzle Reinforcement

1993 ◽  
Vol 115 (4) ◽  
pp. 364-372 ◽  
Author(s):  
H. Chen ◽  
Y.-J. Chao
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Stress Distribution ◽  
Contact Force ◽  
Thin Shell ◽  
Pressure Vessels ◽  
The Finite Element Method ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Shell Analysis

In the thin shell analysis of welded pad reinforced nozzles in pressure vessels, no contact between pad and vessel is often assumed. The significance of this contact force to the stress distribution in the structure is little known. In this paper, stress results from the finite element analysis, which includes the contact force between the pad and the vessel, are reported. A comparison of the finite element results with those from thin shell analysis and experiments shows that the finite element method with contact assumption yields improved theoretical prediction for the stress distribution. The effect of both the gap and friction between the pad and the vessel are also investigated.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

Tire Cornering Simulation Using an Explicit Finite Element Analysis Code

1998 ◽  
Vol 26 (2) ◽  
pp. 109-119 ◽  
Author(s):  
M. Koishi ◽  
K. Kabe ◽  
M. Shiratori
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Test System ◽  
Experimental Results ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Explicit Finite Element ◽  
Explicit Finite Element Analysis ◽  
Element Method

Abstract The finite element method has been used widely in tire engineering. Most tire simulations using the finite element method are static analyses, because tires are very complex nonlinear structures. Recently, transient phenomena have been studied with explicit finite element analysis codes. In this paper, the authors demonstrate the feasibility of tire cornering simulation using an explicit finite element code, PAM-SHOCK. First, we propose the cornering simulation using the explicit finite element analysis code. To demonstrate the efficiency of the proposed simulation, computed cornering forces for a 175SR14 tire are compared with experimental results from an MTS Flat-Trac Tire Test System. The computed cornering forces agree well with experimental results. After that, parametric studies are conducted by using the proposed simulation.

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

scholarly journals Finite Element Analysis of the Multilayered Honeycomb Composite Material Subjected to Impact Loading

2017 ◽  
Vol 54 (1) ◽  
pp. 180-179 ◽  
Author(s):  
Raul Cormos ◽  
Horia Petrescu ◽  
Anton Hadar ◽  
Gorge Mihail Adir ◽  
Horia Gheorghiu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Composite Material ◽  
Experimental Testing ◽  
Finite Element Models ◽  
The Finite Element Method ◽  
Low Velocity ◽  
Element Analysis ◽  
Element Simulation ◽  
Different Levels

The main purpose of this paper is the study the behavior of four multilayered composite material configurations subjected to different levels of low velocity impacts, in the linear elastc domain of the materials, using experimental testing and finite element simulation. The experimental results obtained after testing, are used to validate the finite element models of the four composite multilayered honeycomb structures, which makes possible the study, using only the finite element method, of these composite materials for a give application.

scholarly journals COMPARISON OF SAW BLADE NATURAL FREQUENCIES AND CRITICAL SPEEDS USING CSAW AND FINITE ELEMENT ANALYSIS

2011 ◽  
Author(s):  
J. Poirier ◽  
P. Radziszewski
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Natural Frequencies ◽  
Element Model ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Saw Blade ◽  
Circular Saws ◽  
The Finite Element Model ◽  
Element Method

The natural frequencies of circular saws limit the operating speeds of the saws. Current industry methods of increasing natural frequency include pretensioning, where plastic deformation is induced into the saw. To better model the saw, the finite element model is compared to current software for steel saws; C-SAW, a software program that calculates frequencies for stiffened circular saws. Using C-SAW and the finite element method the results are compared and the finite element method is validated for steel saws.

A Study Effect of Shooting 2 Balls in a Ball Swaging Process on Gram Load Parameter Using Finite Element Analysis

2014 ◽  
Vol 1061-1062 ◽  
pp. 421-426 ◽  
Author(s):  
Panupich Kheunkhieo ◽  
Kiatfa Tangchaichit
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Radial Direction ◽  
Base Plate ◽  
Element Model ◽  
Load Parameter ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Main Component

The purposes of this research are to explore the baseplate and actuator arm deformation which effect to the gram load which occur in the ball swaging process, the main component determining quality of assembly the head stack assembly with the actuator arm. By shooting a ball though the base plate, the component located on the head stack assembly, the base plate plastic deformation takes place and it in expand in radial direction. The base plate then adjoins with the actuator arm. Using the finite element method to reproduce the ball swaging process, we repeated to study effect of the swage press clamp and velocity. The study done by creating the three dimensionals finite element model to analyze and explain characteristics of the baseplate and actuator arm deformation which effect to gram load which effect to the ball swaging process.

Prediction of the Heat-Insulating Crumb Rubber Brick Walls Design by the Finite Element Method

2013 ◽  
Vol 805-806 ◽  
pp. 1575-1582 ◽  
Author(s):  
Weerapol Namboonruang ◽  
Rattanakorn Rawangkul ◽  
Wanchai Yodsudjai ◽  
Trakool Aramraks ◽  
Nutthanan Suphadon
Keyword(s):  
Heat Transfer ◽  
Finite Element Method ◽  
Finite Element ◽  
Economic Factor ◽  
Crumb Rubber ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Good Correspondence ◽  
Soil Cement ◽  
Element Method

Nowadays, materials used to construct house or building wall areconsidered not only in the physical material behaviour but also energy conscious and economic factor. Adding crumb rubber to the brick composite is one of many methods to develop the properties of bricks. As widely known,the finite element method (FEM) is a tool used for finding accurate solutions of the heat transfer equation of materials including the composite bricks. In this paper an investigation of the heat transfer of a soil cement brick containing crumb rubber particles, is presented and compared to results of finite element analysis (FEA) simulation. To determine the effect of crumb rubber to the heat transfer behaviour of soil cement brick, different volume fractions are varied by 10, 20, 30 and 40%. It was reported that a modelling application reveals good correspondence with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document