Non-Linear Modeling and Analysis of Composite Helicopter Blade for Piezoelectric Energy Harvesting

2012 ◽  
Author(s):  
Wander G. R. Vieira ◽  
Fred Nitzsche ◽  
Carlos De Marqui
Keyword(s):  
Energy Harvesting ◽  
Electrical Power ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Resistive Load ◽  
Linear Modeling ◽  
Modeling And Analysis ◽  
Helicopter Blade ◽  
Piezoelectric Energy ◽  
Non Linear

Converting aeroelastic vibrations into electricity for low-power generation has received growing attention over the past few years. Helicopter blades with embedded piezoelectric elements can provide electrical energy to power small electronic components. In this paper, the non-linear modeling and analysis of an electromechanically coupled cantilevered helicopter blade is presented for piezoelectric energy harvesting. A resistive load is considered in the electrical domain of the problem in order to quantify the electrical power output. The non-linear electromechanical model is derived based on the Variational-Asymptotic Method (VAM). The coupled non-linear rotary system is solved in the time-domain. A generalized-α integration method is used to guarantee numerical stability, adding numerical damping at high frequencies. The electromechanical behavior of the coupled rotating blade is investigated for increasing rotating speeds (stiffening effect).

Energy harvesting from quasi-static deformations via bilaterally constrained strips

2018 ◽  
Vol 29 (18) ◽  
pp. 3572-3581
Author(s):  
Suihan Liu ◽  
Ali Imani Azad ◽  
Rigoberto Burgueño
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Mechanical Energy ◽  
Electrical Power ◽  
Energy Resource ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Power Budget ◽  
Piezoelectric Energy ◽  
Static Conditions

Piezoelectric energy harvesting from ambient vibrations is well studied, but harvesting from quasi-static responses is not yet fully explored. The lack of attention is because quasi-static actions are much slower than the resonance frequency of piezoelectric oscillators to achieve optimal outputs; however, they can be a common mechanical energy resource: from large civil structure deformations to biomechanical motions. The recent advances in bio-micro-electro-mechanical systems and wireless sensor technologies are motivating the study of piezoelectric energy harvesting from quasi-static conditions for low-power budget devices. This article presents a new approach of using quasi-static deformations to generate electrical power through an axially compressed bilaterally constrained strip with an attached piezoelectric layer. A theoretical model was developed to predict the strain distribution of the strip’s buckled configuration for calculating the electrical energy generation. Results from an experimental investigation and finite element simulations are in good agreement with the theoretical study. Test results from a prototyped device showed that a peak output power of 1.33 μW/cm2 was generated, which can adequately provide power supply for low-power budget devices. And a parametric study was also conducted to provide design guidance on selecting the dimensions of a device based on the external embedding structure.

scholarly journals Utilization of a magnetic field-driven microscopic motion for piezoelectric energy harvesting

Nanoscale ◽  
2019 ◽  
Vol 11 (43) ◽  
pp. 20527-20533 ◽  
Author(s):  
Sanggon Kim ◽  
Gerardo Ico ◽  
Yaocai Bai ◽  
Steve Yang ◽  
Jung-Ho Lee ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Magnetic Nanoparticles ◽  
Energy Harvesting ◽  
Energy Conversion ◽  
Particle Shape ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Dependent Manner ◽  
Piezoelectric Energy

Magneto–mechano–electrical energy conversion in poly(vinylidenefluoride-trifluoroethylene) piezoelectric nanofibers integrated with magnetic nanoparticles in a particle-shape dependent manner.

Topology Optimization of Piezoelectric Energy Harvesting Devices Subjected to Stochastic Excitation

2010 ◽  
Author(s):  
Zheqi Lin ◽  
Hae Chang Gea ◽  
Shutian Liu
Keyword(s):  
Topology Optimization ◽  
Energy Harvesting ◽  
Electrical Energy ◽  
Ambient Vibration ◽  
Piezoelectric Energy Harvesting ◽  
The Past ◽  
Piezoelectric Energy ◽  
Random Responses ◽  
Pseudo Excitation ◽  
Energy Harvesting Devices

Converting ambient vibration energy into electrical energy using piezoelectric energy harvester has attracted much interest in the past decades. In this paper, topology optimization is applied to design the optimal layout of the piezoelectric energy harvesting devices. The objective function is defined as to maximize the energy harvesting performance over a range of ambient vibration frequencies. Pseudo excitation method (PEM) is applied to analyze structural stationary random responses. Sensitivity analysis is derived by the adjoint method. Numerical examples are presented to demonstrate the validity of the proposed approach.

Piezoelectric Energy Harvesting for Powering Micro Electromechanical Systems (MEMS)

2015 ◽  
Vol 8 (1) ◽  
Author(s):  
A. Majeed
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Piezoelectric Materials ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Wireless Technology ◽  
Power Devices ◽  
Piezoelectric Energy ◽  
Technical Innovations ◽  
Low Power Electronics

Recent advancements in wireless technology and low power electronics such as micro electrome-chanical systems (MEMS), have created a surge of technical innovations in the eld of energy har-vesting. Piezoelectric materials, which operate on vibrations surrounding the system have becomehighly useful in terms of energy harvesting. Piezoelectricity is the ability to transform mechanicalstrain energy, mostly vibrations, to electrical energy, which can be used to power devices. This paperwill focus on energy harvesting by piezoelectricity and how it can be incorporated into various lowpower devices and explain the ability of piezoelectric materials to function as self-charging devicesthat can continuously supply power to a device and will not require any battery for future processes.

Piezoelectric Energy Harvesting From Roadways Based on Pavement Compatible Package

2019 ◽  
Vol 86 (9) ◽  
Author(s):  
He Zhang ◽  
Kangxu Huang ◽  
Zhicheng Zhang ◽  
Tao Xiang ◽  
Liwei Quan
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Mechanical Energy ◽  
Scaling Law ◽  
Piezoelectric Energy Harvesting ◽  
Resistive Load ◽  
Piezoelectric Energy ◽  
Simple Scaling ◽  
Energy Harvesting System ◽  
Combined Parameters

Scavenging mechanical energy from the deformation of roadways using piezoelectric energy transformers has been intensively explored and exhibits a promising potential for engineering applications. We propose here a new packaging method that exploits MC nylon and epoxy resin as the main protective materials for the piezoelectric energy harvesting (PEH) device. Wheel tracking tests are performed, and an electromechanical model is developed to double evaluate the efficiency of the PEH device. Results indicate that reducing the embedded depth of the piezoelectric chips may enhance the output power of the PEH device. A simple scaling law is established to show that the normalized output power of the energy harvesting system relies on two combined parameters, i.e., the normalized electrical resistive load and normalized embedded depth. It suggests that the output power of the system may be maximized by properly selecting the geometrical, material, and circuit parameters in a combined manner. This strategy might also provide a useful guideline for optimization of piezoelectric energy harvesting system in practical roadway applications.

Circuit Development of Piezoelectric Energy Harvesting Device for Recharging Solid-State Batteries

2012 ◽  
Author(s):  
Yuejuan Li ◽  
Marvin H. Cheng ◽  
Ezzat G. Bakhoum
Keyword(s):  
Solid State ◽  
Energy Density ◽  
Energy Harvesting ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Power Sources ◽  
Piezoelectric Energy ◽  
Piezoelectric Elements ◽  
Volume Energy ◽  
Solid State Batteries

Piezoelectric devices have been widely used as a means of transforming ambient vibrations into electrical energy that can be stored and used to power other devices. This type of power generation devices can provide a convenient alternative to traditional power sources used to operate certain types of sensors/actuators, MEMS devices, and microprocessor units. However, the amount of energy produced by these devices is in many cases far too small to directly power an electrical device. Therefore, much of the research into power harvesting has focused on methods of accumulating the energy until a sufficient amount is present, allowing the intended electronics to be powered. Due to the tiny amount of harvestable power from a single device, it is critical to collect vibration energy efficiently. Many research groups have developed various methods to operate the harvesting devices at their resonant frequencies for maximal amount of energy. Different techniques of conversion circuits are also investigated for efficient transformation from mechanical vibration to electrical energy. However, efforts have not been made to the analysis of array configuration of energy harvesting elements. Poor combination of piezoelectric elements, such as phase difference, cannot guarantee the increasing amount of harvested energy. To realize a piezoelectric energy-harvesting device with higher volume energy density, the energy conversion efficiencies of different array configurations were investigated. In the present study, various combinations of piezoelectric elements were analyzed to achieve higher volume energy density. A charging circuit for solid-state batteries with planned energy harvesting strategy was also proposed. With the planned harvesting strategy, the required charging time can be estimated. Thus, the applicable applications can be clearly identified. In this paper, optimal combination of piezoelectric cantilevers and different modes of charging methods were investigated. The results provide a means of choosing the piezoelectric device to be used and estimate the amount of time required to recharge a specific capacity solid-state battery.

A Piezoelectric PZT Ceramic Multilayer Stack for Energy Harvesting Under Dynamic Forces

2011 ◽  
Author(s):  
Tian-Bing Xu ◽  
Emilie J. Siochi ◽  
Jin Ho Kang ◽  
Lei Zuo ◽  
Wanlu Zhou ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
High Performance ◽  
Electrical Power ◽  
Electrical Energy ◽  
Resonance Mode ◽  
Dynamic Force ◽  
Piezoelectric Energy ◽  
Resonance Frequencies ◽  
Dynamic Forces ◽  
Pzt Ceramic

In this paper, we report the study of a “33” longitudinal mode, piezoelectric PZT ceramic multilayer stack (PZT-Stack) with high effective piezoelectric coefficient for broader bandwidth high-performance piezoelectric energy harvesting transducers (PEHTs). The PZT-Stack is composed of 300 layers of 0.1 mm thick PZT plates, with overall dimensions of 32.4 mm × 7.0 mm × 7.0 mm. Experiments were carried out with dynamic forces in a broad bandwidth ranging from 0.5 Hz to 25 kHz. The measured results show that the effective piezoelectric coefficients (EPC, deff) of the PZT-stack is about 1 × 105 pC/N at off-resonance frequencies and 1.39 × 106 pC/N at resonance, which is order of magnitude larger than that of traditional PEHTs. The EPC do not change significantly with applied dynamic forces having root mean square (RMS) values ranging from 1 N to 40 N. In resonance mode, 231 mW of electrical power was harvested at 2,479 Hz with a dynamic force of 11.6 Nrms, and 7.6 mW of electrical power was generated at a frequency of 2,114 Hz with 1 Nrms dynamic force. In off-resonance mode, an electrical power of 18.7 mW was obtained at 680 Hz with a 40 Nrms dynamic force. A theoretical model of energy harvesting for the PZT-Stack was established. The modeled results matched well with experimental measurements. This study demonstrated that structures with high EPC enable PEHTs to harvest more electrical energy from mechanical vibrations or motions, suggesting an effective design for high-performance low-profile PEHTs with potential applications in military, aerospace, and portable electronics. In addition, this study provides a route for using piezoelectric multilayer stacks for active or semi-active adaptive control to damp, harvest or transform unwanted vibrations into useful electrical energy.

Investigating Piezoelectric Energy Harvesting Circuits for Piezoelectric Flags

2015 ◽  
Author(s):  
Anahita Zargarani ◽  
Nima Mahmoodi
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Voltage Drop ◽  
Piezoelectric Energy Harvesting ◽  
Resistive Load ◽  
Dc Voltage ◽  
Wind Speeds ◽  
Piezoelectric Energy ◽  
Alternating Voltage ◽  
Load Circuit

This paper provides a comparison between two different energy harvesting circuits for a piezoelectric flag subjected to uniform flow. Between two circuits tested, one is Simple Resistive Load, and the other one is the standard AC-DC circuit. To experimentally investigate these circuits, the piezoelectric flag output voltage has been studied under various wind speeds in a wind tunnel. The simple resistive load circuit provides an alternating voltage, and not a DC voltage. The standard AC-DC circuit is used to convert the AC voltage into a DC voltage; however, the power dropped as a result of the voltage drop across the forward-biased diodes.

Design, Simulation & Optimization of a MEMS Based Piezoelectric Energy Harvester

2021 ◽  
Vol 12 (07) ◽  
pp. 318-329
Author(s):  
Indrajit Chandra Das ◽  
Md. Arafat Rahman ◽  
Sanjoy Dam
Keyword(s):  
Finite Element Method ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Proof Mass ◽  
Simulation Optimization ◽  
Electrical Energy ◽  
Comsol Multiphysics ◽  
Piezoelectric Energy Harvesting ◽  
The Finite Element Method ◽  
Piezoelectric Energy

Energy harvesting is defined as a process of acquiring energy surrounding a system and converting it into electrical energy for usage. Piezoelectric energy harvesting is a very important concept in energy harvesting in microelectronics. In this report, an analysis of the cantilever type piezoelectric energy harvester is conducted using the finite element method (FEM) based software COMSOL Multiphysics. A unimorph type cantilever beam of the silicon substrate, structural steel as proof mass and support, and PZT-5A material as piezoelectric constitute the physical system.

Sign in / Sign up

Export Citation Format

Share Document