On the Possibility of Frictional Damping with Reduced Wear: A Note on the Applicability of Archard's Law of Adhesive Wear under Conditions of Fretting

2018 ◽  
Vol 21 (1) ◽  
pp. 94-98 ◽  
Author(s):  
Q. Li ◽  
V. L. Popov
Keyword(s):  
Adhesive Wear ◽  
Frictional Damping

scholarly journals Simulation and Experimental Study on Wear of U-Shaped Rings of Power Connection Fittings under Strong Wind Environment

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 735
Author(s):  
Songchen Wang ◽  
Xianchen Yang ◽  
Xinmei Li ◽  
Cheng Chai ◽  
Gen Wang ◽  
...  
Keyword(s):  
Abrasive Wear ◽  
Adhesive Wear ◽  
Surface Hardness ◽  
Wear Depth ◽  
Strong Wind ◽  
Wear Model ◽  
Wind Environment ◽  
Simulation Results ◽  
Oxidation Wear ◽  
Good Agreement

The objective of this study was to investigate the wear characteristics of the U-shaped rings of power connection fittings, and to construct a wear failure prediction model of U-shaped rings in strong wind environments. First, the wear evolution and failure mechanism of U-shaped rings with different wear loads were studied by using a swinging wear tester. Then, based on the Archard wear model, the U-shaped ring wear was dynamically simulated in ABAQUS, via the Umeshmotion subroutine. The results indicated that the wear load has an important effect on the wear of the U-shaped ring. As the wear load increases, the surface hardness decreases, while plastic deformation layers increase. Furthermore, the wear mechanism transforms from adhesive wear, slight abrasive wear, and slight oxidation wear, to serious adhesive wear, abrasive wear, and oxidation wear with the increase of wear load. As plastic flow progresses, the dislocation density in ferrite increases, leading to dislocation plugs and cementite fractures. The simulation results of wear depth were in good agreement with the test value of, with an error of 1.56%.

scholarly journals Global existence, energy decay and blow-up of solutions for wave equations with time delay and logarithmic source

2020 ◽  
Vol 2020 (1) ◽  
Author(s):  
Sun-Hye Park
Keyword(s):  
Time Delay ◽  
Global Existence ◽  
Wave Equations ◽  
Blow Up ◽  
Logarithmic Sobolev Inequality ◽  
Decay Rates ◽  
Infinite Time ◽  
Global Existence Of Solutions ◽  
Frictional Damping ◽  
T Tau

AbstractIn this paper, we study the wave equation with frictional damping, time delay in the velocity, and logarithmic source of the form $$ u_{tt}(x,t) - \Delta u (x,t) + \alpha u_{t} (x,t) + \beta u_{t} (x, t- \tau ) = u(x,t) \ln \bigl\vert u(x,t) \bigr\vert ^{\gamma } . $$ u t t ( x , t ) − Δ u ( x , t ) + α u t ( x , t ) + β u t ( x , t − τ ) = u ( x , t ) ln | u ( x , t ) | γ . There is much literature on wave equations with a polynomial nonlinear source, but not much on the equations with logarithmic source. We show the local and global existence of solutions using Faedo–Galerkin’s method and the logarithmic Sobolev inequality. And then we investigate the decay rates and infinite time blow-up for the solutions through the potential well and perturbed energy methods.

Moving loads on beams on Winkler foundations with passive frictional damping devices

2017 ◽  
Vol 152 ◽  
pp. 211-225 ◽  
Author(s):  
R. Toscano Corrêa ◽  
F.M.F. Simões ◽  
A. Pinto da Costa
Keyword(s):  
Moving Loads ◽  
Frictional Damping

Investigation of the Suitability of Surface Treatments for Dry Cold Extrusion by Process-Oriented Tribological Testing

2015 ◽  
Vol 651-653 ◽  
pp. 473-479 ◽  
Author(s):  
Marco Teller ◽  
Markus Bambach ◽  
Gerhard Hirt ◽  
Ingo Ross ◽  
André Temmler ◽  
...  
Keyword(s):  
Metal Forming ◽  
Adhesive Wear ◽  
Pure Aluminum ◽  
Surface Treatments ◽  
Cold Extrusion ◽  
Workpiece Material ◽  
Initial Yield Stress ◽  
First Results ◽  
Tailored Surfaces ◽  
Steel Aisi

In cold extrusion of aluminum alloys adhesive wear can be prevented by an excessive lubrication of the process. While this causes additional process steps also environmental risks have to be addressed. Hence, dry metal forming, i.e. avoiding lubrication by means of coatings and topography modifications is highly desirable. In this paper first results concerning the behavior of tailored surfaces under dry metal forming conditions for pure aluminum are presented. Different surface treatments (laser polishing and Mo2BC coating) of the tool steel AISI H11 are tested in a compression-torsion-tribometer under conditions adapted from cold extrusion. Normal stresses six times higher than the initial yield stress of the tested workpiece material pure aluminum (AA1050-O) are applied. Furthermore, a strategy for the characterization of aluminum adhesions to the tool is introduced. The influences of different topographies and the presence of a coating on the loss of material due to adhesive wear are investigated.

Sign in / Sign up

Export Citation Format

Share Document