Hydraulic fracturing experiment at the University of Regina Campus

1986 ◽  
Vol 23 (4) ◽  
pp. 548-555 ◽  
Author(s):  
J. D. McLennan ◽  
H. S. Hasegawa ◽  
J -C Roegiers ◽  
Alan M. Jessop
Keyword(s):  
Hydraulic Fracturing ◽  
Stress Component ◽  
Horizontal Stress ◽  
Depth Range ◽  
Precambrian Basement ◽  
Breakdown Pressure ◽  
Overburden Pressure ◽  
Minimum Horizontal Stress ◽  
The University

A hydraulic fracturing stress determination was carried out during May and June, 1979, in a water well intended for the Geothermal Feasibility Project on the campus of the University of Regina, Saskatchewan. Four intervals between depths of 2062 and 2215 m were fractured successfully, one in the Winnipeg Formation (2034–2083 m), two in the Deadwood Formation (2083–2209 m), and one under the Phanerozoic sequence near the top of the Precambrian basement (2209–2215 m).Over the depth range (2062–2215 m) covered by this hydrofracture experiment, the results and inferences are as follow. Downhole breakdown pressure ranges from 42 to 45 MPa, and downhole shut-in pressure from 35 to 42 MPa. The minimum horizontal stress component, σhmin, is taken as being equal to the corresponding shut-in pressure. The vertical stress component, σv, is assumed to be essentially equal to the overburden pressure and varies from 51 to 56 MPa. Whereas σv and σhmin apparently vary smoothly across the Deadwood Formation, the maximum horizontal component, σhmax, appears to undergo a discontinuity in the upper part of the Deadwood Formation, as σHMAX varies from 40 MPa in the Winnipeg Formation to 53 MPa in the upper part of the Precambrian basement. In so far as seismotectonics is concerned, the physical implications of these measurements are that normal faulting should prevail in the Winnipeg (and overlying) formations whereas strike-slip faulting could occur in the Precambrian basement; however, the latter inference has not been firmly established. Breakdown pressure is a useful guide (upper limit) for the potential geothermal demonstration project. Key words: hydraulic fracture, fracture mechanics, faulting, stresses, in situ, breakdown, shut-in pressure, seismotectonics.

A Novel Method and its Application to Define Maximum Horizontal Stress and Stress Path

2021 ◽  
Author(s):  
Jianguo Zhang ◽  
Karthik Mahadev ◽  
Stephen Edwards ◽  
Alan Rodgerson
Keyword(s):  
Fracture Initiation ◽  
Stress Path ◽  
Horizontal Stress ◽  
Geomechanical Model ◽  
Breakdown Pressure ◽  
In Situ Stresses ◽  
Fracture Closure ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

Abstract Maximum horizontal stress (SH) and stress path (change of SH and minimum horizontal stress with depletion) are the two most difficult parameters to define for an oilfield geomechanical model. Understanding these in-situ stresses is critical to the success of operations and development, especially when production is underway, and the reservoir depletion begins. This paper introduces a method to define them through the analysis of actual minifrac data. Field examples of applications on minifrac failure analysis and operational pressure prediction are also presented. It is commonly accepted that one of the best methods to determine the minimum horizontal stress (Sh) is the use of pressure fall-off analysis of a minifrac test. Unlike Sh, the magnitude of SH cannot be measured directly. Instead it is back calculated by using fracture initiation pressure (FIP) and Sh derived from minifrac data. After non-depleted Sh and SH are defined, their apparent Poisson's Ratios (APR) are calculated using the Eaton equation. These APRs define Sh and SH in virgin sand to encapsulate all other factors that influence in-situ stresses such as tectonic, thermal, osmotic and poro-elastic effects. These values can then be used to estimate stress path through interpretation of additional minifrac data derived from a depleted sand. A geomechanical model is developed based on APRs and stress paths to predict minifrac operation pressures. Three cases are included to show that the margin of error for FIP and fracture closure pressure (FCP) is less than 2%, fracture breakdown pressure (FBP) less than 4%. Two field cases in deep-water wells in the Gulf of Mexico show that the reduction of SH with depletion is lower than that for Sh.

Valuation of hydraulic fracturing potentials of organic-rich shales from the Anambra basin using rock mechanical properties from wireline logs

2021 ◽  
Vol 19 (3) ◽  
pp. 45-44
Author(s):  
Homa Viola Akaha-Tse ◽  
Michael Oti ◽  
Selegha Abrakasa ◽  
Charles Ugwu Ugwueze
Keyword(s):  
Mechanical Properties ◽  
Hydraulic Fracturing ◽  
Horizontal Stress ◽  
Shale Formations ◽  
In Situ Stresses ◽  
Anambra Basin ◽  
Wireline Logs ◽  
Rock Mechanical Properties ◽  
Minimum Horizontal Stress

This study was carried out to determine the rock mechanical properties relevant for hydrocarbon exploration and production by hydraulic  fracturing of organic rich shale formations in Anambra basin. Shale samples and wireline logs were analysed to determine the petrophysical, elastic, strength and in-situ properties necessary for the design of a hydraulic fracturing programme for the exploitation of the shales. The results obtained indicated shale failure in shear and barreling under triaxial test conditions. The average effective porosity of 0.06 and permeability of the order of 10-1 to 101 millidarcies showed the imperative for induced fracturing to assure fluid flow. Average Young’s modulus and Poisson’s ratio of about 2.06 and 0.20 respectively imply that the rocks are favourable for the formation and propagation of fractures during hydraulic fracking. The minimum horizontal stress, which determines the direction of formation and growth of artificially induced hydraulic fractures varies from wellto-well, averaging between 6802.62 to 32790.58 psi. The order of variation of the in-situ stresses is maximum horizontal stress>vertical stress>minimum horizontal stress which implies a reverse fault fracture regime. The study predicts that the sweet spots for the exploration and development of the shale-gas are those sections of the shale formations that exhibit high Young’s modulus, low Poisson’s ratio, and high brittleness. The in-situ stresses required for artificially induced fractures which provide pore space for shale gas accumulation and expulsion are adequate. The shales possess suitable mechanical properties to fracture during hydraulic fracturing. Application of these results will enhance the potentials of the onshore Anambra basin as a reliable component in increasing Nigeria’s gas reserves, for the improvement of the nation’s economy and energy security. Key Words: Hydraulic Fracturing, Organic-rich Shales, Rock Mechanical Properties, Petrophysical Properties, Anambra Basin

scholarly journals Rupture Directivity in 3D Inferred From Acoustic Emissions Events in a Mine-Scale Hydraulic Fracturing Experiment

2021 ◽  
Vol 9 ◽  
Author(s):  
José Ángel López-Comino ◽  
Simone Cesca ◽  
Peter Niemz ◽  
Torsten Dahm ◽  
Arno Zang
Keyword(s):  
Hydraulic Fracturing ◽  
Acoustic Emissions ◽  
Local Stress ◽  
Horizontal Stress ◽  
Monitoring Networks ◽  
Rupture Directivity ◽  
Shallow Subsurface ◽  
Minimum Horizontal Stress ◽  
Directivity Effects ◽  
Full Waveforms

Rupture directivity, implying a predominant earthquake rupture propagation direction, is typically inferred upon the identification of 2D azimuthal patterns of seismic observations for weak to large earthquakes using surface-monitoring networks. However, the recent increase of 3D monitoring networks deployed in the shallow subsurface and underground laboratories toward the monitoring of microseismicity allows to extend the directivity analysis to 3D modeling, beyond the usual range of magnitudes. The high-quality full waveforms recorded for the largest, decimeter-scale acoustic emission (AE) events during a meter-scale hydraulic fracturing experiment in granites at ∼410 m depth allow us to resolve the apparent durations observed at each AE sensor to analyze 3D-directivity effects. Unilateral and (asymmetric) bilateral ruptures are then characterized by the introduction of a parameter κ, representing the angle between the directivity vector and the station vector. While the cloud of AE activity indicates the planes of the hydrofractures, the resolved directivity vectors show off-plane orientations, indicating that rupture planes of microfractures on a scale of centimeters have different geometries. Our results reveal a general alignment of the rupture directivity with the orientation of the minimum horizontal stress, implying that not only the slip direction but also the fracture growth produced by the fluid injections is controlled by the local stress conditions.

Predicting the azimuth of natural fractures and in-situ horizontal stress: A case study from Sichuan Basin, China

Geophysics ◽  
2021 ◽  
pp. 1-97
Author(s):  
kai lin ◽  
Bo Zhang ◽  
Jianjun Zhang ◽  
Huijing Fang ◽  
Kefeng Xi ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Data ◽  
Sichuan Basin ◽  
Horizontal Stress ◽  
Seismic Attributes ◽  
Seismic Events ◽  
Natural Fractures ◽  
Microseismic Data ◽  
Maximum Horizontal Stress

The azimuth of fractures and in-situ horizontal stress are important factors in planning horizontal wells and hydraulic fracturing for unconventional resources plays. The azimuth of natural fractures can be directly obtained by analyzing image logs. The azimuth of the maximum horizontal stress σH can be predicted by analyzing the induced fractures on image logs. The clustering of micro-seismic events can also be used to predict the azimuth of in-situ maximum horizontal stress. However, the azimuth of natural fractures and the in-situ maximum horizontal stress obtained from both image logs and micro-seismic events are limited to the wellbore locations. Wide azimuth seismic data provides an alternative way to predict the azimuth of natural fractures and maximum in-situ horizontal stress if the seismic attributes are properly calibrated with interpretations from well logs and microseismic data. To predict the azimuth of natural fractures and in-situ maximum horizontal stress, we focus our analysis on correlating the seismic attributes computed from pre-stack and post-stack seismic data with the interpreted azimuth obtained from image logs and microseismic data. The application indicates that the strike of the most positive principal curvature k1 can be used as an indicator for the azimuth of natural fractures within our study area. The azimuthal anisotropy of the dominant frequency component if offset vector title (OVT) seismic data can be used to predict the azimuth of maximum in-situ horizontal stress within our study area that is located the southern region of the Sichuan Basin, China. The predicted azimuths provide important information for the following well planning and hydraulic fracturing.

scholarly journals In Situ Stress Prediction in Subsurface Rocks: An Overview and a New Method

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Yushuai Zhang ◽  
Shangxian Yin ◽  
Jincai Zhang
Keyword(s):  
Horizontal Stress ◽  
In Situ Stress ◽  
New Method ◽  
Alternative Methods ◽  
Tensile Fracture ◽  
In Situ Stresses ◽  
Stress Estimation ◽  
Minimum Horizontal Stress ◽  
Polygon Method

Methods for determining in situ stresses are reviewed, and a new approach is proposed for a better prediction of the in situ stresses. For theoretically calculating horizontal stresses, horizontal strains are needed; however, these strains are very difficult to be obtained. Alternative methods are presented in this paper to allow an easier way for determining horizontal stresses. The uniaxial strain method is oversimplified for the minimum horizontal stress determination; however, it is the lower bound minimum horizontal stress. Based on this concept, a modified stress polygon method is proposed to obtain the minimum and maximum horizontal stresses. This new stress polygon is easier to implement and is more accurate to determine in situ stresses by narrowing the area of the conventional stress polygon when drilling-induced tensile fracture and wellbore breakout data are available. Using the generalized Hooke’s law and coupling pore pressure and in situ stresses, a new method for estimating the maximum horizontal stress is proposed. Combined it to the stress polygon method, a reliable in situ stress estimation can be obtained. The field measurement method, such as minifrac test, is also analyzed in different stress regimes to determine horizontal stress magnitudes and calibrate the proposed theoretical method. The proposed workflow combined theoretical methods to field measurements provides an integrated approach for horizontal stress estimation.

scholarly journals In Situ Stress and Stress Regime in the Onshore Part of the Northeast Java Basin

2021 ◽  
Vol 44 (2) ◽  
pp. 95-105
Author(s):  
Agus M. Ramdhan
Keyword(s):  
Petroleum Industry ◽  
Horizontal Stress ◽  
In Situ Stress ◽  
Vertical Stress ◽  
Stress Regime ◽  
Severe Erosion ◽  
Tectonically Active ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

In situ stress is importance in the petroleum industry because it will significantly enhance our understanding of present-day deformation in a sedimentary basin. The Northeast Java Basin is an example of a tectonically active basin in Indonesia. However, the in situ stress in this basin is still little known. This study attempts to analyze the regional in situ stress (i.e., vertical stress, minimum and maximum horizontal stresses) magnitude and orientation, and stress regime in the onshore part of the Northeast Java Basin based on twelve wells data, consist of density log, direct/indirect pressure test, and leak-off test (LOT) data. The magnitude of vertical (  and minimum horizontal (  stresses were determined using density log and LOT data, respectively. Meanwhile, the orientation of maximum horizontal stress  (  was determined using image log data, while its magnitude was determined based on pore pressure, mudweight, and the vertical and minimum horizontal stresses. The stress regime was simply analyzed based on the magnitude of in situ stress using Anderson’s faulting theory. The results show that the vertical stress ( ) in wells that experienced less erosion can be determined using the following equation: , where  is in psi, and z is in ft. However, wells that experienced severe erosion have vertical stress gradients higher than one psi/ft ( . The minimum horizontal stress ( ) in the hydrostatic zone can be estimated as, while in the overpressured zone, . The maximum horizontal stress ( ) in the shallow and deep hydrostatic zones can be estimated using equations: and , respectively. While in the overpressured zone, . The orientation of  is ~NE-SW, with a strike-slip faulting stress regime.

scholarly journals Numerical Investigation of the Impacts of Borehole Breakouts on Breakdown Pressure

Energies ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 888 ◽  
Author(s):  
Hua Zhang ◽  
Shunde Yin ◽  
Bernt Aadnoy
Keyword(s):  
Hydraulic Fracturing ◽  
Shear Failure ◽  
In Situ Stress ◽  
Test Results ◽  
Breakdown Pressure ◽  
Borehole Breakout ◽  
Borehole Breakouts ◽  
The Difference ◽  
Mud Pressure

Borehole breakouts appear in drilling and production operations when rock subjected to in situ stress experiences shear failure. However, if a borehole breakout occurs, the boundary of the borehole is no longer circular and the stress distribution around it is different. So, the interpretation of the hydraulic fracturing test results based on the Kirsch solution may not be valid. Therefore, it is important to investigate the factors that may affect the correct interpretation of the breakdown pressure in a hydraulic fracturing test for a borehole that had breakouts. In this paper, two steps are taken to implement this investigation. First, sets of finite element modeling provide sets of data on borehole breakout measures. Second, for a given measure of borehole breakouts, according to the linear relation between the mud pressure and the stress on the borehole wall, the breakdown pressure considering the borehole breakouts is acquired by applying different mud pressure in the model. Results show the difference between the breakdown pressure of a circular borehole and that of borehole that had breakouts could be as large as 82% in some situations.

A Data-Driven Approach to Predict the Breakdown Pressure of the Tight and Unconventional Formation

2021 ◽  
Author(s):  
Zeeshan Tariq ◽  
Murtada Saleh Aljawad ◽  
Mobeen Murtaza ◽  
Mohamed Mahmoud ◽  
Dhafer Al-Shehri ◽  
...  
Keyword(s):  
Neural Network ◽  
Hydraulic Fracturing ◽  
Rock Properties ◽  
Breakdown Pressure ◽  
Rock Samples ◽  
In Situ Stresses ◽  
Fracturing Fluids ◽  
The Neural Network ◽  
Different Types

Abstract Unconventional reservoirs are characterized by their extremely low permeabilities surrounded by huge in-situ stresses. Hydraulic fracturing is a most commonly used stimulation technique to produce from such reservoirs. Due to high in situ stresses, breakdown pressure of the rock can be too difficult to achieve despite of reaching maximum pumping capacity. In this study, a new model is proposed to predict the breakdown pressures of the rock. An extensive experimental study was carried out on different cylindrical specimens and the hydraulic fracturing stimulation was performed with different fracturing fluids. Stimulation was carried out to record the rock breakdown pressure. Different types of fracturing fluids such as slick water, linear gel, cross-linked gels, guar gum, and heavy oil were tested. The experiments were carried out on different types of rock samples such as shales, sandstone, and tight carbonates. An extensive rock mechanical study was conducted to measure the elastic and failure parameters of the rock samples tested. An artificial neural network was used to correlate the breakdown pressure of the rock as a function of fracturing fluids, experimental conditions, and rock properties. Fracturing fluid properties included injection rate and fluid viscosity. Rock properties included were tensile strength, unconfined compressive strength, Young's Modulus, Poisson's ratio, porosity, permeability, and bulk density. In the process of data training, we analyzed and optimized the parameters of the neural network, including activation function, number of hidden layers, number of neurons in each layer, training times, data set division, and obtained the optimal model suitable for prediction of breakdown pressure. With the optimal setting of the neural network, we were successfully able to predict the breakdown pressure of the unconventional formation with an accuracy of 95%. The proposed method can greatly reduce the prediction cost of rock breakdown pressure before the fracturing operation of new wells and provides an optional method for the evaluation of tight oil reservoirs.

Field Experiments on Hydraulic Fracturing

1972 ◽  
Vol 12 (01) ◽  
pp. 69-77 ◽  
Author(s):  
Hilmar von Schonfeldt ◽  
C. Fairhurst
Keyword(s):  
Hydraulic Fracturing ◽  
Pore Pressure ◽  
Compressive Stress ◽  
Rupture Strength ◽  
Breakdown Pressure ◽  
Near Surface ◽  
Fracturing Process ◽  
Fluid Penetration ◽  
Regional Stresses

Abstract Hydraulic fracturing experiments at two underground and one near-surface location in igneous and shale formations were described. The tests were designed to study the feasibility of hydraulic fracturing as a method of determining in-situ stresses. The tests were carried out in open holes of 2-3/8-in. diameter. Fracturing tests on two 5-ft diameter cores were also reported. The test results revealed an increase in the magnitude of the stress as the face of an opening was approached from inside a rock mass. Horizontal fractures also were observed in areas of reportedly high lateral stress, providing some evidence for the validity of the providing some evidence for the validity of the principle of least resistance. The results also principle of least resistance. The results also indicate that caution must be used in using the shut-in pressure as a measure of the least compressive stress. Introduction Hydraulic fracturing is best known as a well stimulation method. There are other important applications, however, for which the process shows great potential. One of these is in the area of in-situ stress determination as suggested by Scheidegger Kehle and Fairhurst. The mechanics of the fracturing process is the same in any application, and improvement of the method may therefore be expected through a mutual exchange of experience in each of these areas. The theory of the hydraulic fracturing technique relates measurable quantities such as the breakdown pressure and the instantaneous shut-in pressure to pressure and the instantaneous shut-in pressure to the tectonic stresses and certain physical rock properties. properties. Assuming negligible pore pressure and fluid penetration, the break-down pressure (pC) at the penetration, the break-down pressure (pC) at the instant of fracture initiation is given by the following expressions....................(1) when the fracture extends in a "radial" direction (in a plane parallel to the axis of the borehole). And...................(2) when the fracture extends in a direction normal to the borehole axis. Corresponding expressions that include the effect of pore pressure and fluid penetration are given in the literature Because our work was done in dry and impermeable formations, Eqs. 1 and 2 are considered adequate. These formulae are based on the assumption that the borehole is drilled parallel to 3 and that the rock behaves as a linearly elastic isotropic material; it also assumes that the fracture is initiated in a direction perpendicular to the least compressive stress, i.e., 2 or 3, respectively, in accordance with the principle of least resistance. The terms "radial" and "normal" fractures are introduced in place of the commonly used terms "vertical" and "horizontal" fractures in order to avoid possible confusion in the event a borehole is drilled in a direction other than the vertical. Eqs. 1 and 2 establish a simple relation between the breakdown pressure and the regional (far-field) stresses. It also has been suggested that the instantaneous shut-in pressure is a measure for the least compressive stress because a fracture will propagate in a direction normal to it. Therefore, propagate in a direction normal to it. Therefore, or ..........................(3) Thus Eqs. 1 and 3 may serve to estimate the regional stresses 1, and 2 provided it is known that a radial fracture was generated, and it is possible to determine the rupture strength (K ). possible to determine the rupture strength (K ). Similarly Eqs. 2 or 3 will give an estimate of the stress 3. Scheidegger and Kehle determined regional stresses through a similar analysis of hydraulic fracturing data. SPEJ P. 69

Sign in / Sign up

Export Citation Format

Share Document