Effect of low-frequency vibrations on MRR, EWR and Ra in powder-mixed electrical discharge machining

2020 ◽  
Vol 34 (22n24) ◽  
pp. 2040153
Author(s):  
Quang Dung Le ◽  
Huu Phan Nguyen ◽  
Tien Long Banh ◽  
Duc Toan Nguyen
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Low Frequency ◽  
Lower Surface ◽  
Dielectric Fluid ◽  
Electrode Wear ◽  
Maximum Increase ◽  
Lower Electrode ◽  
Powder Mixed Edm

In this study, the effects of low-frequency vibrations on machining SKD61 steel workpiece in electrical discharge machining (EDM) with titanium powder-mixed dielectric fluid were investigated. The results showed that the vibrations incorporated into the workpiece in powder-mixed EDM (PMEDM) led to significant improvement in machining efficiency. The material removal rate had the maximum increase of 141.7% with 70.2% of lower electrode wear rate and 69.9% of lower surface roughness. Hence, it is proved that the effectiveness of vibration in PMEDM can be improved.

Surfactant and graphite powder–assisted electrical discharge machining of titanium alloy

2016 ◽  
Vol 231 (4) ◽  
pp. 641-657 ◽  
Author(s):  
Murahari Kolli ◽  
Adepu Kumar
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Recast Layer ◽  
Dielectric Fluid ◽  
Recast Layer Thickness

Surfactant and graphite powder–assisted electrical discharge machining was proposed and experiments were performed on titanium alloy in this investigation. Analysis was carried out to observe changes in dielectric fluid behaviour, material removal rate, surface roughness, recast layer thickness, surface topography and energy-dispersive X-ray spectroscopy. It was found out that the addition of surfactant to dielectric fluid (electrical discharge machining oil + graphite powder) improved the material removal rate and surface roughness. It was noticed to have reduced the recast layer thickness and agglomeration of graphite and sediment particles. Biface material migrations between the electrode and the workpiece surface were identified, and migration behaviour was powerfully inhibited by the mixing of surfactant. Surfactant added into dielectric fluid played an important role in the discharge gap, which increased the conductivity, and suspended debris particles in dielectric fluid reduced the abnormal discharge conditions of the machine and improved the overall machining efficiency.

Deep Hole of AISI P20 Mold Steel Material by Electrical Discharge Machining

2014 ◽  
Vol 590 ◽  
pp. 244-248
Author(s):  
Jamkamon Kamonpong ◽  
Pichai Janmanee
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Side Surface ◽  
Copper Electrode ◽  
Electrode Wear ◽  
Steel Material ◽  
Suitable Parameter ◽  
Aisi P20 ◽  
Off Time

This research aimed to study the machining efficiency of AISI P20 steel by Electrical Discharge Machining (EDM) using rod copper electrode to machining material by 50 mm depth of machining was mainly assessed from Materials Removal Rate (MRR) and Electrode Wear Ratio (EWR). From the experiment designed to use Taguchi technique of data analysis and suitable parameter prediction, the highest MRR was at on-time of 150 μs, off-time of 2 μs and electric current level was at 15 A or 0.25 A/mm2. Predicted value was at 19.2395 mm3/min which was equal to real experiment, showing Materials Removal Rate of 19.647 mm3/min (with error of 2.12 percent) .Moreover, it was found that gap would increase with the size of electrode and depth of machining caused by movement of particles removed from side surface of electrode, which cause micro sparks at the side of the material workpiece.

The effect of magnesium content on drilling of Al-Mg-Ti alloy by hole electrical discharge machining process

2020 ◽  
Vol 235 (1-2) ◽  
pp. 125-133
Author(s):  
Omer Eyercioglu ◽  
Kursad Gov
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Magnesium Content ◽  
Machining Process ◽  
Electrode Wear ◽  
Ti Alloy ◽  
Ti Alloys ◽  
Mg Content

This study presents an experimental investigation of small hole electrical discharge machining of Al-Mg-Ti alloys. A series of drilling operations were carried out for exploring the effect of magnesium content. Holes of 2 mm diameter and 15 mm depth were drilled using tubular single-hole rotary brass electrodes. The rates of material removal and electrode wear, surface roughness, overcut, average recast layer thickness, taper height and angle were studied for Al-Mg-Ti alloys contain 2%, 4%, 6%, 8%, 10%, 12%, and 14% Mg. The results show that the material removal rate is increasing with increasing Mg content while the rate of electrode wear is almost unchanged. Due to decreasing the melting temperature of the Al-Mg-Ti alloy with increasing Mg content, more metal melts and vaporizes during electrical discharge machining drilling. Therefore, more overcut and taper, thicker white layer, and rougher surfaces were measured for higher Mg content.

Analysis of MRR and TWR on OHNS Die Steel with Different Electrodes Using Electrical Discharge Machining

2016 ◽  
Vol 22 ◽  
pp. 112-120 ◽  
Author(s):  
S. Nallusamy
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Work Piece ◽  
Tool Wear Rate

Electrical Discharge Machining is a machining method primarily used for hard metals or those that are impossible to be machined with traditional techniques. The experimental investigation of material removal rate and tool wear rate during machining of oil hardened non-shrinking steel with brass and copper electrodes using EDM machine was carried out in this paper. This investigation presents the analysis and evaluation of heat affected zones and surface finish of the work piece using different tool electrodes and varying the machine parameters. The commercial grade kerosene oil has been used as dielectric fluid. The effect of various important EDM parameters such as discharge current (Ip) 2 to12A, pulse duration (Ton and Toff) and sparking voltage (V) of 80±5% have been used to yield the response in terms of Material Removal Rate (MRR) and Tool Wear Rate (TWR). Further a detailed analysis of the heat affected regions was also been carried out by using scanning electron microscopy.

Electrical Discharge Machining of SiC and Gr Reinforced 6061-T6 Aluminum Alloy Hybrid Composite Fabricated by Friction Stir Processing

2013 ◽  
Author(s):  
Murahari Kolli ◽  
Devaraj Aruri ◽  
Kumar Adepu
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Processing ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Hybrid Composites ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Machining Parameters ◽  
Machining Performance ◽  
Friction Stir

Aluminum based hybrid composites are advanced materials having the properties of high hardness, superior wear resistance, strength, high elevated temperature and low thermal expansion coefficient. These hybrid composites are widely used in industries like automobile and aerospace. In this present paper 6061-T6 Aluminum alloy reinforced with SiC and Gr particles, hybrid composites are fabricated by using Friction stir processing (FSP) technique. It prevents the further development of hybrid composites for machining by nonconventional methods like water jet and laser cutting process. Electrical discharge machining (EDM) is used for machining the complex shapes of the material. This paper presents an overview of EDM studies conducted on the Al-SiC/Gr hybrid composites using a copper electrode in EDM. The EDM experiment machining parameters such as the dielectric fluid, peak current, pulse on, pulse off times are changed to explore their effects on machining performance, material removal rate (MRR), Tool wear rate (TWR), and surface roughness (SR). It is observed that the MRR and SR of the Al-SiC/Gr hybrid composites increase with an increase in the current.

scholarly journals Recent Advances and Perceptive Insights into Powder-Mixed Dielectric Fluid of EDM

Micromachines ◽  
2020 ◽  
Vol 11 (8) ◽  
pp. 754 ◽  
Author(s):  
Asarudheen Abdudeen ◽  
Jaber E. Abu Qudeiri ◽  
Ansar Kareem ◽  
Thanveer Ahammed ◽  
Aiman Ziout
Keyword(s):  
Tool Wear ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Dielectric Fluids ◽  
Advanced Machining ◽  
Low Efficiency ◽  
Edm Process ◽  
Powder Mixed Edm

Electrical discharge machining (EDM) is an advanced machining method which removes metal by a series of recurring electrical discharges between an electrode and a conductive workpiece, submerged in a dielectric fluid. Even though EDM techniques are widely used to cut hard materials, low efficiency and high tool wear remain remarkable challenges in this process. Various studies, such as mixing different powders to dielectric fluids, are progressing to improve their efficiency. This paper reviews advances in the powder-mixed EDM process. Furthermore, studies about various powders used for the process and its comparison are carried out. This review looks at the objectives of achieving a more efficient metal removal rate, reduction in tool wear, and improved surface quality of the powder-mixed EDM process. Moreover, this paper helps researchers select suitable powders which are exhibiting better results and identifying different aspects of powder-mixed dielectric fluid of EDM.

scholarly journals Multi-Performance Optimization in Electrical Discharge Machining of Al2O3 Ceramics Using Taguchi Base AHP Weighted TOPSIS Method

Processes ◽  
2021 ◽  
Vol 9 (9) ◽  
pp. 1647
Author(s):  
Yue-Peng Zeng ◽  
Chiang-Lung Lin ◽  
Hong-Mei Dai ◽  
Yan-Cherng Lin ◽  
Jung-Chou Hung
Keyword(s):  
Process Parameters ◽  
Performance Optimization ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Statistical Technique ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Relative Closeness ◽  
Machining Parameter

The main application of electrical discharge machining in ceramic processing is limited to conductive ceramics. However, the most commonly used non-conductive potteries in modern industry, such as aluminum oxide (Al2O3), also reveal the limitations of choosing a suitable process. In this study, Taguchi based TOPSIS coupled with AHP weight method to optimize the machining parameters of EDM on Al2O3 leads to better multi-performance. The results showed that the technique is suitable for tackling multi-performance machining parameter optimization. The adhesive foil had a significant impact on material removal rate, electrode wear rate, and surface roughness, according to the findings. In addition, the response graph of relative closeness is used to determine the optimal combination levels of machining parameters. A confirmation test revealed a good agreement between predicted and experimental preference values at an optimum combination of the input parameters. The suggested experimental and statistical technique is a simple, practical, and reliable methodology for optimizing EDM process parameters on Al2O3 ceramics. This approach might be utilized to optimize and improve additional process parameters in the future.

Investigation on the Effect of Multi Wall Carbon Nano Tubes in Wire Electrical Discharge Machining of Hybrid Metal Matrix Composites

2014 ◽  
Vol 592-594 ◽  
pp. 456-460
Author(s):  
S. Ramesh ◽  
N. Natarajan ◽  
Vijayan Krishnaraj ◽  
K. Sathish Kumar
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Characteristics ◽  
Machining Process ◽  
Dielectric Fluid ◽  
Wire Electrical Discharge Machining ◽  
Matrix Composites ◽  
Machining Performance ◽  
Carbon Nano Tubes

Wire Electrical Discharge Machining (WEDM) is an very accurate non-traditional machining process for producing parts with accurate dimensions and complex shapes. The performance of WEDM is measured by evaluating the parameters like Material Removal Rate (MRR), Surface Roughness (Ra), cracks, voids, pores and recast layer. In this paper, an attempt is made to improve the machining performance by adding multi wall carbon nanotube (MWCNT) with dielectric fluid. The MRR, Ra and surface characteristics are compared with surface that is machined using dielectric fluid with and without MWCNT. The results show that addition of MWCNT improves the MRR and surface finish.

Comparative study of low-frequency vibrations assigned to a workpiece in EDM and PMEDM

2020 ◽  
Vol 34 (22n24) ◽  
pp. 2040145
Author(s):  
Quang Dung Le ◽  
Huu Phan Nguyen ◽  
Tien Long Banh ◽  
Duc Toan Nguyen
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Low Frequency ◽  
Quality Measures ◽  
Processing Efficiency ◽  
Machined Surface ◽  
Low Frequency Vibration ◽  
Better Than

This study deals about the influence of vibrations incorporated into a workpiece during powder-mixed electrical discharge machining (PMEDM) on quality measures such as material removal rate (MRR), surface roughness [Formula: see text] and microhardness. It has been found that the low-frequency vibration incorporated into the workpiece positively affects the processing efficiency of electrical discharge machining (EDM) and PMEDM. However, the effect of low-frequency vibration in PMEDM has been better than EDM. The higher vibration frequency significantly improves the MRR and [Formula: see text] in PMEDM. The MRR has been improved by 95.89% and with lower [Formula: see text] of 63.2% in PMEDM. The hardness of the machined surface after PMEDM using titanium powder mixed in dielectric liquid was increased approximately two times as compared with conventional EDM.

Sign in / Sign up

Export Citation Format

Share Document