DX-MOCCII Based Fully Cascadable Second Order Current-Mode Universal Filter

2018 ◽  
Vol 27 (07) ◽  
pp. 1850113 ◽  
Author(s):  
Ashok Kumar ◽  
Sajal K. Paul
Keyword(s):  
Notch Filter ◽  
Current Mode ◽  
Second Order ◽  
Current Conveyors ◽  
Band Pass Filter ◽  
Universal Filter ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Band Pass ◽  
Circuit Configuration

The paper presents a new second-order single input multiple output (SIMO) type current mode (CM) universal filter. The proposed circuit uses two dual-X second generation multi-output current conveyors (DX-MOCCII), two grounded capacitors and three grounded resistors. The circuit configuration realizes low-pass filter (LPF), high-pass filter (HPF), band-pass filter (BPF), notch filter (NF) and all-pass filter (APF) responses simultaneously at different output terminals. The new circuit enjoys the features of low input impedance and high output impedance, which is desirable and useful for cascadability in CM circuits. For realizing the universal filter responses, the proposed circuit configuration does not require matching constraint of passive components and both active and passive sensitivities are found low. In addition, the extension of the proposed circuit as a resistorless universal filter has also been presented. As an application of the proposed filter, inverting band pass output is connected to a negative unity gain current follower in a close loop to design voltage and CM multiphase sinusoidal oscillators (MSOs). Comparison of the proposed configuration with available literature is given. The PSPICE simulation of the filter and its application as MSO are performed to verify the agreement with the theoretical proposition.

A New DVCC+ Based Second-Order Current-Mode Universal Filter Consisting of Only Grounded Capacitors

2017 ◽  
Vol 26 (09) ◽  
pp. 1750130 ◽  
Author(s):  
Ahmet Abaci ◽  
Erkan Yuce
Keyword(s):  
Notch Filter ◽  
Current Mode ◽  
Second Order ◽  
Pass Band ◽  
Current Conveyors ◽  
Universal Filter ◽  
Pass Filter ◽  
Low Pass ◽  
Band Pass ◽  
High Output Impedance

In this paper, a new second-order current-mode universal filter using only two plus-type differential voltage current conveyors, three resistors and two grounded capacitors is proposed. The proposed circuit with two identical inputs and three outputs can simultaneously provide second-order high output impedance low-pass, band-pass and notch filter responses. Also, it can realize high-pass and all-pass filter responses with interconnection of relevant output currents. It can be easily tuned electronically. It can be operated properly at high frequencies. A number of simulations based on SPICE program and an experimental test are achieved in order to demonstrate the performance of the proposed filter.

Second Order Universal Filter Using Four Terminal Floating Nullor (FTFN)

2019 ◽  
Vol 28 (06) ◽  
pp. 1950091 ◽  
Author(s):  
Ashish Ranjan ◽  
Subrahmanyam Perumalla ◽  
Ravi Kumar ◽  
Vista John ◽  
Shantikumar Yumnam
Keyword(s):  
Notch Filter ◽  
Second Order ◽  
Band Pass Filter ◽  
Universal Filter ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Input Selection ◽  
Single Output ◽  
Low Pass ◽  
Four Terminal Floating Nullor

In this research paper, a voltage mode second order universal filter using Four Terminal Floating Nullor (FTFN) is presented. The proposed design uses Three Input Single Output (TISO) for the realization of all filter responses namely Low Pass Filter (LPF), High Pass Filter (HPF), Band Pass Filter (BPF), Notch Filter (NF) and All Pass Filter (APF) by using proper input selection. The analog building block, FTFN is simply realized with two commercially available AD844 ICs. The proposed second order universal filter comes with a single FTFN block with four passive components in which no component matching is required for filter realization. The universal filter is well verified using PSPICE simulation. In addition, experimental verification for the second order APF has been performed that confirms the theoretical expectations.

Fractional Order Capacitor in First-Order and Second-Order Filter

2020 ◽  
Vol 12 (1) ◽  
pp. 75-78
Author(s):  
Kanchan Sengar ◽  
Arun Kumar
Keyword(s):  
Fractional Order ◽  
Second Order ◽  
Active Filters ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Order Filter ◽  
Low Pass ◽  
Band Pass ◽  
High Pass

Background: Fractional order Butterworth and Chebyshev (low-pass filter circuits, highpass filter circuits and band-pass filters circuits) types of first and second order filter circuits have been simulated and their transfer function are derived. The effect of change of the fractional order α on the behavior of the circuits is investigated. Objective: This paper presents the use of fractional order capacitor in active filters. The expressions for the magnitude, phase, the quality factor, the right-phase frequencies, and the half power frequencies are derived and compared with their previous counterpart. Methods: The circuits have been simulated using Orcad as well as MATLAB for the different value of α. We have developed the fractional gain and phase equations for low pass filter circuits, high pass filter circuits and band pass filter circuits in Sallen-Key topology. Results: It is observed that the bandwidth increases significantly with fractional order other than unity for the low pass as well as high pass and band pass filters. Conclusion: We have also seen that in the frequency domain, the magnitude and phase plots in the stop band change nearly linearly with the fractional order. If we compare the fractional Butterworth filters for low-pass and high-pass type with conventional filters then we find that the roll-off rate is equal to the next higher order filter.

scholarly journals New Single VDCC-based Explicit Current- Mode SRCO Employing All Grounded Passive Components

2014 ◽  
Vol 18 (2) ◽  
pp. 81 ◽  
Author(s):  
Dinesh Prasad ◽  
D. R. Bhaskar ◽  
M. Srivastava
Keyword(s):  
Process Model ◽  
Current Mode ◽  
Model Parameters ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Quadrature Oscillator ◽  
Sinusoidal Oscillator ◽  
Low Pass ◽  
Band Pass

This paper proposes a new single resistancecontrolled sinusoidal oscillator (SRCO) which employs only onevoltage differencing current conveyor (VDCC), two groundedresistors and two grounded capacitors. The presented circuitconfiguration offers the following advantageous features (i)explicit current-mode output with independent control ofcondition of oscillation (CO) and frequency of oscillation (FO) (ii)low active and passive sensitivities and (iii) a very good frequencystability. The proposed structure can also be configured as (a)trans-admittance low pass filter and band pass filter and (b)quadrature oscillator. The validity of the proposed SRCO,quadrature oscillator and trans-admittance low pass filter andband pass filter has been verified by PSPICE simulations usingTSMC CMOS 0.18μm process model parameters.

scholarly journals Multifunction Filter/Inverse Filter Configuration Employing CMOS CDBAs

2019 ◽  
Vol 8 (4) ◽  
pp. 8844-8853
Keyword(s):  
Active Filters ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Low Pass Filter ◽  
High Pass Filter ◽  
Low Pass ◽  
Multifunction Filter ◽  
Band Pass ◽  
High Pass ◽  
Circuit Configuration

A voltage-mode (VM) multifunction configuration for the realization of conventional active filters and inverse active filters (IAF) using two current differencing buffered amplifiers and six passive elements has been presented. The proposed structure can realize low pass filter/inverse low pass filter (LPF/ILPF), high pass filter /inverse high pass filter (HPF/IHPF), and band pass filter/ Inverse band pass filter (BPF/IBPF) from the same circuit topology by appropriate choice(s) of the branch impedance(s). PSPICE simulations with CMOS current differencing buffered amplifiers implemented in 0.18µm CMOS TSMC technology have been presented to establish the workability of the proposed circuit configuration.

scholarly journals Analysis and Simulation of Active Filters Using Operational Transconductance Amplifier (OTA)

2017 ◽  
Vol 13 (15) ◽  
pp. 170
Author(s):  
Haitham K. Ali ◽  
Jihan S. Abdaljabar
Keyword(s):  
Cutoff Frequency ◽  
Current Mode ◽  
High Gain ◽  
Angular Frequency ◽  
Active Filters ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Large Bandwidth ◽  
High Output Impedance

As the transistors are continuously scaling down, it becomes necessary to reduce voltage supply and power requirements of the circuit to increase its performance and stability. Whereas, current- mode devices require less number of stages with high output impedance results in improved performance and large bandwidth as compared to voltage-mode techniques. OTA are current-mode device that takes voltage as input and produces current as output with high gain and large bandwidth. The frequency bands were parameters were determined such as the cutoff frequency (fc), the band width (BW), the quality factor (Q), and the angular frequency (Wo). In this paper the design and the simulation of the transfer function has been done by using (MATLAB) in order to obtain the frequency response for all types of filter (the low pass filter, high pass filter, band pass filter and band stop filter).

scholarly journals DESIGN OF BAND-PASS FILTERS WITH NON-EQUIRIPPLE FREQUENCY RESPONSES

2019 ◽  
Vol 22 (3) ◽  
pp. 5-23
Author(s):  
Evgeniy N. Chervinskiy
Keyword(s):  
Frequency Response ◽  
Special Functions ◽  
Band Pass Filter ◽  
System Of Equations ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Frequency Responses ◽  
Band Pass ◽  
Standard Values ◽  
Circuit Elements

Introduction. Band-pass filters circuit elements can be calculated by converting low-pass filter (LPF) parameters, which is the prototype of the designed band-pass filter. The conversion causes problems in case calculated values of circuit elements (resistors and capacitors) are out of standard values determined by the GOST standard. Obviously, frequency characteristics of band-pass filters are distorted when replacing the calculated values of circuit elements by the standard ones. The number of circuit elements with values different from standard can be reduced to zero by solving an additional system of equations that connects parameters of designed and reintroduced non-equiripple frequency responses. Objective. The objective of this work is to develop a calculation method of band-pass ladder filters with values of circuit elements corresponding to standard ones. Materials and methods. The filter design process includes two stages. The first stage is a parameters calculation of a polynomial LPF prototype. The calculated parameters are determined as a system of equations solution set. The equations are formed by equating coefficients of variables raised to the same powers in transfer function (TF) expressions of designed and realized filters. Initial characteristics are the filter order and frequency response unevenness. The transition to the standard values of circuit elements can be done when solving another system of equations that connects LPF converted parameters with unknown parameters of reintroduced non-equiripple frequency response. Results. TF of LPF prototypes up to the fifth order and frequency responses of band-pass filters (BPF) and bandrejection filters up to the tenth order are presented. Analytical expressions of non-equiripple and equiripple frequency responses are used to estimate distortions of the latter when a band-pass filter center frequency is tuned by using variable inductors or capacitors. The integral quadratic function of a variable is taken as a measure of real frequency response distortions. The tenth order BPF calculation example is given. Conclusion. The presented calculation methods of band-pass filters and given example demonstrate possibilities of the filter design method based on the systems of non-linear equations solution. In contrast to approximation methods of ideal filter frequency response by using special functions and tabular filters design, the presented method allows high-order filter calculation for any initial requirements without using reference data.

Sign in / Sign up

Export Citation Format

Share Document