scholarly journals A COUPLED BEM AND ENERGY FLOW METHOD FOR MID-HIGH FREQUENCY INTERNAL ACOUSTIC

2010 ◽  
Vol 18 (01) ◽  
pp. 69-85 ◽  
Author(s):  
SBASTIEN BESSET ◽  
M. N. ICHCHOU ◽  
L. JÉZÉQUEL
Keyword(s):  
Hybrid Method ◽  
High Frequency ◽  
Energy Flow ◽  
High Frequency Range ◽  
Frequency Range ◽  
Flow Method ◽  
Complete Calculation ◽  
The Mean ◽  
Acoustic Cavities ◽  
Power Densities

This paper deals with the behavior of acoustic cavities in the mid-high frequency range. The method proposed here is based on an energy flow method named Simplified Energy Method (MES). MES method is quite efficient in the mid-high frequency range but the directivity of the boundary sources is not well estimated. We propose a hybrid method which couples MES and the Boundary Element Method (BEM). Thus, the BEM method is used to estimate the direct field, considering a "correct" directivity. As a complete calculation is not adapted to BEM in mid-high frequency range because of the calculation costs, we only apply BEM on the domains including boundary sources. Other parts of the system and the reverberated field are estimated by the mean of MES method. This hybrid method leads to a consistent prediction of injected power densities. Numerical comparisons prove the efficiency of the proposed reformulation.

scholarly journals A hybrid method for vibroacoustic coupling

2008 ◽  
pp. 689-699
Author(s):  
Emeline Sadoulet-Reboul ◽  
Alain Le Bot ◽  
Joël Perret-Liaudet
Keyword(s):  
Radiative Transfer ◽  
Hybrid Method ◽  
High Frequency ◽  
Low Frequency ◽  
Energy Sources ◽  
High Frequency Range ◽  
Engine Compartment ◽  
Frequency Range ◽  
Transfer Method

hybrid method is proposed to study the noise radiated in the high frequency range by a gearbox inside an engine compartment. Due to its elastodynamic characteristics, the vibratory behaviour of the transmission lies in the low frequency range. However, the noise radiated is rather in the high frequency range facing the size of the acoustical cavity. Thus the proposed hybrid method allows to couple a low-frequency vibratory approach to the radiative transfer method used for the high frequency acoustical calculation. The coupling is realized through equivalent energy sources introduced on the surface of the vibrating structure.

Electromagnetic Property of La0.7Sr0.3MnO3/Ag Composite at High Frequency

2015 ◽  
Vol 655 ◽  
pp. 182-185
Author(s):  
Ke Lan Yan ◽  
Run Hua Fan ◽  
Min Chen ◽  
Kai Sun ◽  
Xu Ai Wang ◽  
...  
Keyword(s):  
High Frequency ◽  
Single Phase ◽  
Low Frequency ◽  
Electromagnetic Property ◽  
High Frequency Range ◽  
Frequency Range ◽  
Free Electron Concentration ◽  
Theoretical Simulation ◽  
Electrical And Magnetic Properties ◽  
Three Phase

The phase structure, and electrical and magnetic properties of La0.7Sr0.3MnO3(LSMO)-xAg (xis the mole ratio,x=0, 0.3, 0.5) composite were investigated. It is found that the sample withx=0 is single phase; the samples withx=0.3 and 0.5 present three phase composite structure of the manganese oxide and Ag. With the increasing of Ag content, the grain size of the samples increases and the grain boundaries transition from fully faceted to partially faceted. The permittivity of spectrum (10 MHz - 1 GHz) and the theoretical simulation reveal that the plasma frequencyfpincrease with Ag content, due to the increasing of free electron concentration, which is further supported by the enhancement of conductivity. While for the permeability (μr'), theμr'decrease with the increasing of Ag content at low frequency range (f< 20 MHz), while at the relative high frequency range (f> 300 MHz), theμr'increased with Ag content. Therefore, the introduction of elemental Ag resulted in a higherμr'at the relative high frequency range.

An Impedance-Based Approach for Rods With Shear-Type Damping Layer Treatment

2013 ◽  
Vol 135 (1) ◽  
Author(s):  
P. W. Wang ◽  
D. Q. Zhuang
Keyword(s):  
High Frequency ◽  
Continuous Model ◽  
Damping Coefficient ◽  
System Response ◽  
Traditional Model ◽  
Constrained Layer Damping ◽  
High Frequency Range ◽  
Frequency Range ◽  
Shear Type ◽  
Shear Spring

An impedance-based approach for analyzing an axial rod with shear-type damping layer treatment is proposed. The rod and shear-type damping layer are regarded as two subsystems and both impedances are calculated analytically. The system impedance can be obtained through the impedance coupling between the host rod and the damping layer. The shear-type damping layer is regarded as a shear spring with complex shear modulus. Under the traditional model, the damping coefficient diminishes with the increasing frequency. The paper develops two shear-type damping layer models, including the single degree-of-freedom (SDOF) model and continuous model to predict the behavior of the damping layer. Both damping layer models are compared with the traditional model and the system responses from these models are validated by finite element method (FEM) code COMSOL Multiphysics. Results show that the damping coefficients of both the traditional shear-spring model and SDOF model diminish as the increasing frequency so that the system responses are discrepant with that from COMSOL in the high frequency range. On the other hand, the system response from the continuous model is consistent with that from COMSOL in the full frequency range. Hence, the continuous damping layer model can predict a correct damping coefficient in the high frequency range and this property can be also employed to improve the analysis of the constrained-layer damping treated structures. Finally, the modal loss factor and fundamental frequency of the system with respect to different damping layer thicknesses are presented using the developed approach.

Electromagnetic properties of porous 3D carbon-based structures in high frequency range

2021 ◽  
pp. 76-83
Author(s):  
E.G. Shashkova ◽  
◽  
N.I. Valunets ◽  
M.I. Demidenko ◽  
A.G. Paddubskaya ◽  
...  
Keyword(s):  
High Frequency ◽  
Electromagnetic Properties ◽  
High Frequency Range ◽  
Frequency Range ◽  
Carbon Based
Sign in / Sign up

Export Citation Format

Share Document