INVESTIGATION ON DRY SLIDING WEAR BEHAVIOR OF TITANIUM DIOXIDE-REINFORCED MAGNESIUM MATRIX COMPOSITE

2021 ◽  
pp. 2150106
Author(s):  
P. C. ELUMALAI ◽  
R. GANESH
Keyword(s):  
Titanium Dioxide ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Wear Mechanisms ◽  
Sliding Wear ◽  
Normal Load ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Significant Change

In this work, the dry sliding wear behaviors of pure monolithic magnesium and magnesium–titanium dioxide (Mg–TiO2) composites were studied using pin-on-disc tribometer against an oil-hardened nonshrinking die steel (OHNS) counter-disc with a normal load of 0.5–2[Formula: see text]kg and a sliding velocity of 1.5–2.5[Formula: see text][Formula: see text] with the sliding distance and wear track diameter of 1500[Formula: see text]m and 90[Formula: see text]mm, respectively. The pin samples were characterized for their microstructural, nanomechanical and tribological properties such as wear rate, coefficient of friction and wear fractographs. Scanning electron microscopy (SEM) was used to analyze the worn-out surfaces of each pin sample in order to identify the different types of wear and wear mechanisms and the chemical constituents of each element were quantified by energy-dispersive spectroscopy. The influence of TiO2 reinforcements on the nanomechanical behavior was studied by nanoindentation technique. As compared with pure Mg, the nanoindentation strengths of Mg–1.5TiO2, Mg–2.5TiO2 and Mg–5TiO2 composites were found to increase by 11.9%, 22.2% and 35.8%, respectively, which was due to the addition of TiO2 particles and also due to the good bonding at the interface of TiO2 and magnesium particles. From the wear test results, a significant change in wear rate was observed with the change in normal load than that of sliding speed, whereas a significant change in coefficient of friction was noticed with the changes in both normal load and sliding velocity. The dominant wear mechanisms involved under the testing conditions were identified through plotting the contour maps and SEM fractographs. Also, from the fractographs it was noticed that delamination and plowing effect have been the significant wear mechanisms observed during low wear rate of samples, whereas melting, delamination and oxidation wear have been observed during high wear rate of pure Mg and its composites.

scholarly journals Microstructural Characterization and Evaluation of Sliding Wear of Hastelloy C276 under Different Loading Conditions

2019 ◽  
Vol 8 (12) ◽  
pp. 2841-2845
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Frictional Force ◽  
Sliding Wear ◽  
Normal Load ◽  
Dry Sliding Wear ◽  
Material Surface ◽  
Dry Sliding ◽  
Loading Conditions ◽  
Sem Images

Hastelloy C276 is investigated for dry sliding wear against an EN 31 stainless steel (hardness 60 HRC) at 298 K. The tribological properties such as frictional force, coefficient of friction and the wear rate on the material surface at different sliding distance are examined under different loading conditions. In the dry wear test at 40 N load, the wear rate increased by 300% as compared to 10, 20, 30 N loading conditions. The experimental results indicated reduction in coefficient of friction values and thus an increase in the frictional force with the increase in normal load. SEM images of worn out surfaces confirm that the delamination and adhesion causes the material removal from the surface in dry sliding. Further, the analysis of the hardness characteristics of worn out surfaces shows surface hardening during sliding wear process under 40 N load

Optimization of dry sliding wear parameters of recursive friction stir processed aluminium 7075 alloy

2020 ◽  
pp. 135065012094161
Author(s):  
G Girish ◽  
V Anandakrishnan
Keyword(s):  
Electron Microscopy ◽  
Wear Rate ◽  
Sliding Wear ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Friction Stir ◽  
Sliding Distance

In this work, the dry sliding wear behaviour of recursively friction stir processed AA7075 was investigated using a pin-on-disc wear testing apparatus. The microstructure of the processed specimen was probed using optical microscopy, transmission electron microscopy and atomic force microscopy. Experiments were conducted using Taguchi experimental design by varying three different parameters like load, sliding velocity and sliding distance, and the analysis of variance was performed to identify the influence of the parameters over the wear rate. From the main effect plot, the combination of 9.81 N of load, 2 m/s of sliding velocity and a sliding distance of 2000 m was identified as the optimum levels that minimize the wear rate. The regression model was developed to calculate the wear rate, and the validation test was performed with the optimum parameter combination and compared with the experimental results. Wear tracks were examined using field-emission scanning electron microscopy to identify the type of wear mechanism.

Effect of Fine TiC Particle Reinforcement on the Dry Sliding Wear Behavior of In Situ Synthesized ZA27 Alloy

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Roshita David ◽  
Rupa Dasgupta ◽  
B. K. Prasad
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Base Alloy ◽  
Dry Sliding Wear ◽  
Wear Volume ◽  
Dry Sliding ◽  
Material Loss

The in situ method of making zinc-aluminum composites wherein TiC has been introduced has been investigated in the present paper for its microstructural, physical, and dry sliding wear behavior and compared with the base alloy. In the present study, ZA-27 alloy reinforced with 5 and 10 vol % TiC was taken into consideration. The results indicate that the wear rate and coefficient of friction of composites were lower than that of base alloy. The material loss in terms of both wear volume loss and wear rate increases with increase in load and sliding distance, respectively, while coefficient of friction follows a reverse trend with increase in load. Better performance was obtained for 5% TiC reinforcement than with 10% probably due to agglomeration of particles resulting in nonuniform dispersion. Worn surfaces were analyzed by scanning electron microscopy (SEM) analysis.

scholarly journals Dry sliding wear performance of AA7075/MoS2 composite materials

2021 ◽  
Vol 9 ◽  
Author(s):  
R. Kousik Kumaar ◽  
◽  
K. Somasundara Vinoth ◽  
Kavitha M ◽  
◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Wear Rate ◽  
Response Surface ◽  
Sliding Wear ◽  
Specific Wear Rate ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Molybdenum Disulphide ◽  
Pin On Disc

This article aims in exploring the dry sliding wear performances on the aluminum (AA7075) metal matrix composites reinforced with molybdenum disulphide which is a solid lubricant using response surface methodology (RSM). Specific Wear Rate (SWR) for the AA7075 pure alloy, AA7075+2wt% molybdenum disulphide and AA7075+4wt% molybdenum disulphide were measured according to ASTM G99 standards in pin-on-disc apparatus. Design of experiments was selected with changed parameters like the varying percentage of molybdenum disulphide (%), applied load (N), and sliding velocity (m/s) based on Central Composite Design in response surface methodology considering them as continuous factors. Experiments for the specific wear rate of pure alloy and the composites were conducted. The volume loss was measured using the pin-on-disc apparatus from which the specific wear rate value was calculated. The obtained results are analyzed and a mathematical model was formulated using the response surface methodology. The optimum level parameters for the specific wear rate has been identified and the results of the experiment specify that the sliding velocity and molybdenum disulphide percentage have a substantial role in controlling the wear behaviour of composites when compared with the other parameter. The optimum condition for the specific wear rate was identified and experimented with for studying the result.

scholarly journals Modeling and Analysis for Wear Performance in Dry Sliding of Epoxy/Glass/PTW Composites Using Full Factorial Techniques

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
M. Sudheer ◽  
Ravikantha Prabhu ◽  
K. Raju ◽  
Thirumaleshwara Bhat
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Hybrid Composites ◽  
Normal Load ◽  
Glass Fibers ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Wear Performance ◽  
Full Factorial

The dry sliding friction and wear behavior of epoxy hybrid composites reinforced with glass fibers and a varying amount of potassium titanate whiskers (PTWs) fabricated by vacuum hand layup method were studied. The influence of normal load, sliding velocity, and whisker content on both friction coefficient and specific wear rate was investigated on a pin-on-disc machine. The tests were conducted at ambient conditions based on the 3 × 3 (3 factors at 3 levels) full factorial design. Analysis of variance (ANOVA) was performed to obtain the contribution of control parameters on friction coefficient and wear rate. The density and hardness of the composites were found to be enhanced with the PTW loading. The friction coefficient and wear resistance of the hybrid composites were found to be improved with the whisker content and were also greatly influenced by normal load and sliding velocity. A correlation between dry sliding wear behaviors of composites with wear parameters was obtained by multiple regressions. The worn out surface of selected samples was observed under scanning electron microscope (SEM) to identify wear mechanisms. This study revealed that the addition of the ceramic microfillers such as PTW improves the wear performance of the epoxy/glass polymer composites significantly.

scholarly journals Studying The Effect of Reinforcing by Sicp on The Dry Sliding Wear Behavior and Mechanical Properties of AL- 4% CU Matrix Alloy

2013 ◽  
Vol 6 (2) ◽  
pp. 139-153
Author(s):  
Israa .A.K
Keyword(s):  
Mechanical Properties ◽  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Base Material ◽  
Weight Percent ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Cu Alloy

This research is devoted to study the effect of addition of different weight percent from SiCp ( 2, 4, 6, 8 ) to Al– 4 Cu alloy which have been fabricated by liquid metallurgy method on the dry sliding wear behavior and mechanical properties. Wear characteristics of Al–SiC composites have been investigated under dry sliding conditions and compared with base alloy. Dry sliding wear tests have been carried out using pin-on-disk wear test under normal applied loads 5, 10, 15 and 20 N and at different sliding velocity of (2.7, 3.7, 4.7) m/sec. It was also observed that the wear rate varies linearly with increases normal applied load but lower in composites as compared to the base material. The wear mechanism appears to be oxidative for both Al – Cu alloy and composites under the given conditions of load and sliding velocity as indicated by optical microscopic of the worn surfaces. Further, it was found from the experimentation that the wear rate decreases linearly with increasing weight percent of silicon carbide. The best results have been obtained at 8 % wt SiC . We also observed that the yield strength, tensile strength increases with increasing wt% of SiC , but the ductility decreases.

Physical, mechanical and dry sliding wear properties of non-woven viscose fabric epoxy-based polymer composites: An optimization study

2021 ◽  
pp. 135065012110689
Author(s):  
Debabrata Panda ◽  
Krunal M Gangawane
Keyword(s):  
Polymer Composites ◽  
Sliding Wear ◽  
Normal Load ◽  
Operating Conditions ◽  
Dry Sliding Wear ◽  
Operating Parameters ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Wear Properties ◽  
Area Density

Polymer-based composites have been widely used in the enhanced tribological technologies of various automobile, aerospace industry, sports, etc. The epoxy-based polymer composites reinforced with glass fiber have significantly improved the wear inhibitors and ultimate strength along with ultra-low density than other available materials. This current research aims to fabricate a variation of such non-woven viscose-based polymer composites for various weight fractions (100–400 GSM) with a constant fiber loading of 30 wt% and subsequently analyze its physical, mechanical, and tribological properties under various operating parameters. The density of the fabricated composite exhibits an increase of magnitude with an increase in weight fraction. The composites consist of 400 GSM fabric showing a higher tensile, impact, flexural strength, hardness, and inter lamina shear strength (ILSS). A pin-on-disc wear set-up held dry sliding wear tests of various nonwoven viscose fabric-based composites under various operating parameters like sliding velocity, sliding distance, area density, and normal load. A Taguchi-based L16 orthogonal array design was utilized to estimate the optimal behavior for maximum wear resistance for operating conditions. The result reveals that the normal load over the composite contributes the highest towards wear on a composite compared to area density, sliding velocity, and distance. The wear phenomena have been verified with SEM micrographs to characterize various wear phenomena like fiber rapture, ploughing, micro-cracks, and wear lines.

scholarly journals Optimization of Dry Sliding Wear Performance of Ceramic Whisker Filled Epoxy Composites Using Taguchi Approach

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
M. Sudheer ◽  
Ravikantha Prabhu ◽  
K. Raju ◽  
Thirumaleshwara Bhat
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Normal Load ◽  
Epoxy Composites ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Performance ◽  
Casting Technique ◽  
Pin On Disc ◽  
Sliding Distance

This study evaluates the influence of independent parameters such as sliding velocity (A), normal load (B), filler content (C), and sliding distance (D) on wear performance of potassium-titanate-whiskers (PTW) reinforced epoxy composites using a statistical approach. The PTW were reinforced in epoxy resin to prepare whisker reinforced composites of different compositions using vacuum-assisted casting technique. Dry sliding wear tests were conducted using a standard pin on disc test setup following a well planned experimental schedule based on Taguchi’s orthogonal arrays. With the signal-to-noise (S/N) ratio and analysis of variance (ANOVA) optimal combination of parameters to minimize the wear rate was determined. It was found that inclusion of PTW has greatly improved the wear resistance property of the composites. Normal load was found to be the most significant factor affecting the wear rate followed by (C), (D), and (A). Interaction effects of various control parameters were less significant on wear rate of composites.

scholarly journals Process Optimization and Wear Behavior of Red Mud Reinforced Aluminum Composites

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Rajesh Shanmugavel ◽  
Thirumalai Kumaran Sundaresan ◽  
Uthayakumar Marimuthu ◽  
Pethuraj Manickaraj
Keyword(s):  
Wear Rate ◽  
Red Mud ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Experimental Result ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Grey Relational

This work presents the application of hybrid approach for optimizing the dry sliding wear behavior of red mud based aluminum metal matrix composites (MMCs). The essential input parameters are identified as applied load, sliding velocity, wt.% of reinforcement, and hardness of the counterpart material, whereas the output responses are specific wear rate and Coefficient of Friction (COF). The Grey Relational Analysis (GRA) is performed to optimize the multiple performance characteristics simultaneously. The Principle Component Analysis (PCA) and entropy methods are applied to evaluate the values of weights corresponding to each output response. The experimental result shows that the wt.% of reinforcements (Q=34.9%) followed by the sliding velocity (Q=34.5%) contributed more to affecting the dry sliding wear behavior. The optimized conditions are verified through the confirmation test, which exhibited an improvement in the grey relational grade of specific wear rate and COF by 0.3 and 0.034, respectively.

scholarly journals On dry sliding wear of ECAPed Al-Mg-Zn alloy: Wear rate and coefficient of friction relationship

2021 ◽  
Vol 60 (1) ◽  
pp. 927-939
Author(s):  
Maged Elhefnawey ◽  
G.L. Shuai ◽  
Z. Li ◽  
M. Nemat-Alla ◽  
D.T. Zhang ◽  
...  
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Sliding Wear ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Zn Alloy
Sign in / Sign up

Export Citation Format

Share Document