scholarly journals Optimization of Dry Sliding Wear Performance of Ceramic Whisker Filled Epoxy Composites Using Taguchi Approach

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
M. Sudheer ◽  
Ravikantha Prabhu ◽  
K. Raju ◽  
Thirumaleshwara Bhat
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Normal Load ◽  
Epoxy Composites ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Performance ◽  
Casting Technique ◽  
Pin On Disc ◽  
Sliding Distance

This study evaluates the influence of independent parameters such as sliding velocity (A), normal load (B), filler content (C), and sliding distance (D) on wear performance of potassium-titanate-whiskers (PTW) reinforced epoxy composites using a statistical approach. The PTW were reinforced in epoxy resin to prepare whisker reinforced composites of different compositions using vacuum-assisted casting technique. Dry sliding wear tests were conducted using a standard pin on disc test setup following a well planned experimental schedule based on Taguchi’s orthogonal arrays. With the signal-to-noise (S/N) ratio and analysis of variance (ANOVA) optimal combination of parameters to minimize the wear rate was determined. It was found that inclusion of PTW has greatly improved the wear resistance property of the composites. Normal load was found to be the most significant factor affecting the wear rate followed by (C), (D), and (A). Interaction effects of various control parameters were less significant on wear rate of composites.

OPTIMIZATION AND ANALYSIS OF DRY SLIDING WEAR BEHAVIOR OF STIR CASTED AlSi6Cu4–TiO2 COMPOSITE USING CENTRAL COMPOSITE DESIGN

2019 ◽  
Vol 26 (09) ◽  
pp. 1950052
Author(s):  
SUBBARAYAN SIVASANKARAN
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Performance ◽  
Microstructural Investigation ◽  
Confirmation Test ◽  
The Matrix ◽  
Sliding Distance

The present research paperfocusses on manufacture of AlSi6Cu4–3 wt.% TiO2 metal matrix composite (MMC) through liquid metallurgy route, and the manufactured composites are tested for their dry sliding wear behavior using response surface methodology (RSM). The extensive microstructural investigation is carried out to examine the dispersion of Titania particles, its bonding ability, and embedment characteristics with the matrix. The wear rate on the developed MMC is investigated and predicted using regression model. Further, the confirmation test is conducted to validate the model. The microstructures of the composite had revealed that TiO2 particles are dispersed in the Al matrix. Further, the surface plots show that the wear rate started to vary linearly with the function of load whereas the wear rate starts to vary nonlinearly with the function of the sliding velocity and the sliding distance. In addition, the worn surfaces were investigated through the scanning electron microscopewhich addressed the wear mechanisms and revealed that TiO2 particles enhance the wear performance of aluminum alloy by a reduction in material removal at all wear conditions.

scholarly journals Influence of Test Conditions on Sliding Wear Performance of High Velocity Air Fuel-Sprayed WC–CoCr Coatings

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3074
Author(s):  
Kaveh Torkashvand ◽  
Vinod Krishna Selpol ◽  
Mohit Gupta ◽  
Shrikant Joshi
Keyword(s):  
Wear Rate ◽  
Test Performance ◽  
Sliding Wear ◽  
Normal Load ◽  
Specific Wear Rate ◽  
Wear Behaviour ◽  
Wear Performance ◽  
Test Conditions ◽  
Test Parameters ◽  
Sliding Distance

Sliding wear performance of thermal spray WC-based coatings has been widely studied. However, there is no systematic investigation on the influence of test conditions on wear behaviour of these coatings. In order to have a good understanding of the effect of test parameters on sliding wear test performance of HVAF-sprayed WC–CoCr coatings, ball-on-disc tests were conducted under varying test conditions, including different angular velocities, loads and sliding distances. Under normal load of 20 N and sliding distance of 5 km (used as ‘reference’ conditions), it was shown that, despite changes in angular velocity (from 1333 rpm up to 2400 rpm), specific wear rate values experienced no major variation. No major change was observed in specific wear rate values even upon increasing the load from 20 N to 40 N and sliding distance from 5 km to 10 km, and no significant change was noted in the prevailing wear mechanism, either. Results suggest that no dramatic changes in applicable wear regime occur over the window of test parameters investigated. Consequently, the findings of this study inspire confidence in utilizing test conditions within the above range to rank different WC-based coatings.

Dry Sliding Wear Behavior of 2218 Al-Alloy-Al2O3(TiO2) Hybrid Composites

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Vineet Tirth
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Hybrid Composites ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Aged Alloy ◽  
Dry Sliding ◽  
Al Alloy ◽  
Mathematical Relationship ◽  
Sliding Distance

AA2218–Al2O3(TiO2) composites are synthesized by stirring 2, 5, and 7 wt % of 1:2 mixture of Al2O3:TiO2 powders in molten AA2218 alloy. T61 heat-treated composites characterized for microstructure and hardness. Dry sliding wear tests conducted on pin-on-disk setup at available loads 4.91–13.24 N, sliding speed of 1.26 m/s up to sliding distance of 3770 m. Stir cast AA2218 alloy (unreinforced, 0 wt % composite) wears quickly by adhesion, following Archard's law. Aged alloy exhibits lesser wear rate than unaged (solutionized). Mathematical relationship between wear rate and load proposed for solutionized and peak aged alloy. Volume loss in wear increases linearly with sliding distance but drops with the increase in particle wt % at a given load, attributed to the increase in hardness due to matrix reinforcement. Minimum wear rate is recorded in 5 wt % composite due to increased particles retention, lesser porosity, and uniform particle distribution. In composites, wear phenomenon is complex, combination of adhesive and abrasive wear which includes the effect of shear rate, due to sliding action in composite, and abrasive effect (three body wear) of particles. General mathematical relationship for wear rate of T61 aged composite as a function of particle wt % load is suggested. Fe content on worn surface increases with the increase in particle content and counterface temperature increases with the increase in load. Coefficient of friction decreases with particle addition but increases in 7 wt % composite due to change in microstructure.

Optimization of dry sliding wear parameters of recursive friction stir processed aluminium 7075 alloy

2020 ◽  
pp. 135065012094161
Author(s):  
G Girish ◽  
V Anandakrishnan
Keyword(s):  
Electron Microscopy ◽  
Wear Rate ◽  
Sliding Wear ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Friction Stir ◽  
Sliding Distance

In this work, the dry sliding wear behaviour of recursively friction stir processed AA7075 was investigated using a pin-on-disc wear testing apparatus. The microstructure of the processed specimen was probed using optical microscopy, transmission electron microscopy and atomic force microscopy. Experiments were conducted using Taguchi experimental design by varying three different parameters like load, sliding velocity and sliding distance, and the analysis of variance was performed to identify the influence of the parameters over the wear rate. From the main effect plot, the combination of 9.81 N of load, 2 m/s of sliding velocity and a sliding distance of 2000 m was identified as the optimum levels that minimize the wear rate. The regression model was developed to calculate the wear rate, and the validation test was performed with the optimum parameter combination and compared with the experimental results. Wear tracks were examined using field-emission scanning electron microscopy to identify the type of wear mechanism.

scholarly journals Dry sliding wear performance of AA7075/MoS2 composite materials

2021 ◽  
Vol 9 ◽  
Author(s):  
R. Kousik Kumaar ◽  
◽  
K. Somasundara Vinoth ◽  
Kavitha M ◽  
◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Wear Rate ◽  
Response Surface ◽  
Sliding Wear ◽  
Specific Wear Rate ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Molybdenum Disulphide ◽  
Pin On Disc

This article aims in exploring the dry sliding wear performances on the aluminum (AA7075) metal matrix composites reinforced with molybdenum disulphide which is a solid lubricant using response surface methodology (RSM). Specific Wear Rate (SWR) for the AA7075 pure alloy, AA7075+2wt% molybdenum disulphide and AA7075+4wt% molybdenum disulphide were measured according to ASTM G99 standards in pin-on-disc apparatus. Design of experiments was selected with changed parameters like the varying percentage of molybdenum disulphide (%), applied load (N), and sliding velocity (m/s) based on Central Composite Design in response surface methodology considering them as continuous factors. Experiments for the specific wear rate of pure alloy and the composites were conducted. The volume loss was measured using the pin-on-disc apparatus from which the specific wear rate value was calculated. The obtained results are analyzed and a mathematical model was formulated using the response surface methodology. The optimum level parameters for the specific wear rate has been identified and the results of the experiment specify that the sliding velocity and molybdenum disulphide percentage have a substantial role in controlling the wear behaviour of composites when compared with the other parameter. The optimum condition for the specific wear rate was identified and experimented with for studying the result.

scholarly journals Modeling and Analysis for Wear Performance in Dry Sliding of Epoxy/Glass/PTW Composites Using Full Factorial Techniques

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
M. Sudheer ◽  
Ravikantha Prabhu ◽  
K. Raju ◽  
Thirumaleshwara Bhat
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Hybrid Composites ◽  
Normal Load ◽  
Glass Fibers ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Wear Performance ◽  
Full Factorial

The dry sliding friction and wear behavior of epoxy hybrid composites reinforced with glass fibers and a varying amount of potassium titanate whiskers (PTWs) fabricated by vacuum hand layup method were studied. The influence of normal load, sliding velocity, and whisker content on both friction coefficient and specific wear rate was investigated on a pin-on-disc machine. The tests were conducted at ambient conditions based on the 3 × 3 (3 factors at 3 levels) full factorial design. Analysis of variance (ANOVA) was performed to obtain the contribution of control parameters on friction coefficient and wear rate. The density and hardness of the composites were found to be enhanced with the PTW loading. The friction coefficient and wear resistance of the hybrid composites were found to be improved with the whisker content and were also greatly influenced by normal load and sliding velocity. A correlation between dry sliding wear behaviors of composites with wear parameters was obtained by multiple regressions. The worn out surface of selected samples was observed under scanning electron microscope (SEM) to identify wear mechanisms. This study revealed that the addition of the ceramic microfillers such as PTW improves the wear performance of the epoxy/glass polymer composites significantly.

INVESTIGATION ON DRY SLIDING WEAR BEHAVIOR OF TITANIUM DIOXIDE-REINFORCED MAGNESIUM MATRIX COMPOSITE

2021 ◽  
pp. 2150106
Author(s):  
P. C. ELUMALAI ◽  
R. GANESH
Keyword(s):  
Titanium Dioxide ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Wear Mechanisms ◽  
Sliding Wear ◽  
Normal Load ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Significant Change

In this work, the dry sliding wear behaviors of pure monolithic magnesium and magnesium–titanium dioxide (Mg–TiO2) composites were studied using pin-on-disc tribometer against an oil-hardened nonshrinking die steel (OHNS) counter-disc with a normal load of 0.5–2[Formula: see text]kg and a sliding velocity of 1.5–2.5[Formula: see text][Formula: see text] with the sliding distance and wear track diameter of 1500[Formula: see text]m and 90[Formula: see text]mm, respectively. The pin samples were characterized for their microstructural, nanomechanical and tribological properties such as wear rate, coefficient of friction and wear fractographs. Scanning electron microscopy (SEM) was used to analyze the worn-out surfaces of each pin sample in order to identify the different types of wear and wear mechanisms and the chemical constituents of each element were quantified by energy-dispersive spectroscopy. The influence of TiO2 reinforcements on the nanomechanical behavior was studied by nanoindentation technique. As compared with pure Mg, the nanoindentation strengths of Mg–1.5TiO2, Mg–2.5TiO2 and Mg–5TiO2 composites were found to increase by 11.9%, 22.2% and 35.8%, respectively, which was due to the addition of TiO2 particles and also due to the good bonding at the interface of TiO2 and magnesium particles. From the wear test results, a significant change in wear rate was observed with the change in normal load than that of sliding speed, whereas a significant change in coefficient of friction was noticed with the changes in both normal load and sliding velocity. The dominant wear mechanisms involved under the testing conditions were identified through plotting the contour maps and SEM fractographs. Also, from the fractographs it was noticed that delamination and plowing effect have been the significant wear mechanisms observed during low wear rate of samples, whereas melting, delamination and oxidation wear have been observed during high wear rate of pure Mg and its composites.

scholarly journals Dry Sliding Wear Behaviour of Titanium (Grade 5) Alloy by Using Response Surface Methodology

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
S. R. Chauhan ◽  
Kali Dass
Keyword(s):  
Sliding Wear ◽  
Normal Load ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Speed ◽  
Grade 5 ◽  
Titanium Grade ◽  
Sliding Distance ◽  
Sliding Wear Behaviour

The dry sliding wear behaviour of titanium (Grade 5) alloy has been investigated in order to highlight the mechanisms responsible for the poor wear resistance under different applied normal load, sliding speed, and sliding distance conditions. Design of experimental technique, that is, response surface methodology (RSM), has been used to accomplish the objective of the experimental study. The experimental plan for three factors at three levels using face-centre central composite design (CCD) has been employed. The results indicated that the specific wear rate increases with an increase in the applied normal load and sliding speed. However, it decreases with an increase in the sliding distance and a decrease in the sliding speed. The worn surfaces of the titanium alloy specimens were analyzed with the help of scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) techniques. The predicted result also shows the close agreement with the experimental results and hence the developed models could be used for prediction of wear behaviour satisfactorily.

scholarly journals Dry Sliding Wear and Mechanical Characterization of Mg Based Composites by Uniaxial Cold Press Technique

2017 ◽  
Vol 62 (3) ◽  
pp. 1851-1856 ◽  
Author(s):  
P. Selva Kumar ◽  
K. Ponappa ◽  
M. Udhayasankar ◽  
B. Aravindkumar
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Physical And Mechanical Properties ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cold Press ◽  
Pin On Disc ◽  
Magnesium Composites

AbstractDry sliding wear tests are performed on magnesium composites produced by uniaxial cold press technique by using pin-on-disc. Co-efficient of friction and wear rate of magnesium composites are measured under a load of 5 N and sliding velocity of 0.2 ms-1. Porosity, Vickers’s micro hardness, X-Ray Diffraction (XRD) results are presented to characterize the physical and mechanical properties of magnesium composites. Worn surfaces are inspected by Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Three types of wear mechanisms namely abrasive, adhesive and oxidation were observed. The wear rate was found to be low for 2wt% of HAP (3.6×10-6cm3/m) and co-efficient of friction was observed as 0.8.

scholarly journals An investigation on dry sliding wear behavior of Al6061/ Titanium carbide/ Basalt hybrid metal matrix composites

2021 ◽  
Vol 13 (4) ◽  
pp. 139-150
Author(s):  
P. MUTHU
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Principal Component ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Matrix Composites ◽  
Relational Analysis ◽  
Grey Relational ◽  
Sliding Distance

Dry sliding wear plays an important role in selecting material for automotive and aerospace applications. Researchers have been exploring novel aluminum matrix composites (AMC), which offer minimum wear rate for various tribological applications. The present work involves multi-objective optimization for dry sliding wear behavior of Al6061 reinforced with 6 % of Titanium carbide and 4% of basalt hybrid metal matrix composites using principal component analysis (PCA)-based grey relational analysis (GRA). In this article, the effects of input variables of wear parameters such as applied load, sliding speed and sliding distance were investigated on different output responses, namely the wear rate, friction force and specific wear rate. Taguchi’s L9 orthogonal array with three-level settings was chosen for conducting experiments. Three output responses in each experiment were normalized into a weighted grey relational grade using grey relational analysis coupled with the principal component analysis. The analysis of variance indicated that sliding distance is the most influential parameter followed by load and sliding velocity that contributes to the quality characteristics. Optimal results have been verified through additional experiments.

Sign in / Sign up

Export Citation Format

Share Document