scholarly journals COMBINED USE OF PARALLEL-PLATE COMPRESSION AND FINITE ELEMENT MODELING TO ANALYZE THE MECHANICAL PROPERTIES OF INTACT PORCINE LENS

2018 ◽  
Vol 18 (07) ◽  
pp. 1840013 ◽  
Author(s):  
KEHAO WANG ◽  
DEMETRIOS T. VENETSANOS ◽  
JIAN WANG ◽  
BARBARA K. PIERSCIONEK
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Young’S Modulus ◽  
Contact Mechanics ◽  
Compression Test ◽  
Parallel Plate ◽  
Young's Modulus ◽  
Theory Model ◽  
Fe Model ◽  
Compression Tests

The objective of this study is to explore the feasibility of a compression test for measuring mechanical properties of intact eye lenses using novel parallel plate compression equipment to compare the accuracy of implementing a classical Hertzian model and a newly proposed adjusted Hertzian model to calculate Young’s modulus from compression test results using finite element (FE) analysis. Parallel-plate compression tests were performed on porcine lenses. An axisymmetric FE model was developed to simulate the experimental process to evaluate the accuracy of using the classical Hertzian theory of contact mechanics as well as a newly proposed adjusted Hertzian theory model for calculating the equivalent Young’s modulus. By fitting the force-displacement relation obtained from FE simulations to both the classical and adjusted Hertzian theory model and comparing the calculated modulus to the input modulus of the FE model, the results demonstrated that the classical Hertzian theory model overestimated the Young’s modulus with a proportional error of over 10%. The adjusted Hertzian theory model produced results that are closer to original input values with error ratios all lower than 1.29%. Measurements of three porcine lenses from the parallel plate compression experiments were analyzed with resulting values of Young’s modulus of between 3.2[Formula: see text]kPa and 4.3[Formula: see text]kPa calculated. This study demonstrates that the adjusted Hertzian theory of contact mechanics can be applied in conjunction with the parallel-plate compression system to investigate the overall mechanical behavior of intact lenses.

scholarly journals Evaluating Mechanical Properties of Thin Layers using Nanoindentation and Finite-Element Modeling: Implanted Metals and Deposited Layers

1996 ◽  
Vol 438 ◽  
Author(s):  
J. A. Knapp ◽  
D. M. Follstaedt ◽  
J. C. Barbour ◽  
S. M. Myers ◽  
J. W. Ager ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Finite Element Modeling ◽  
Yield Stress ◽  
Young’S Modulus ◽  
Layer Thickness ◽  
Young's Modulus ◽  
Thin Layers ◽  
Element Modeling ◽  
Surface Modified

AbstractWe present a methodology based on finite-element modeling of nanoindentation data to extract reliable and accurate mechanical properties from thin, hard films and surface-modified layers on softer substrates. The method deduces the yield stress, Young's modulus, and hardness from indentations as deep as 50% of the layer thickness.

scholarly journals Finite Element Analysis of the Nanomechanics of Hard Coatings on a Soft Polymer Substrate by a Spherical Indenter

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Chunlai Tian ◽  
Pengfei Duan
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Viscoelastic Model ◽  
Coating System ◽  
Element Analysis ◽  
Soft Polymer ◽  
Indentation Response

Composite has been widely used in various fields due to its advanced performance. To reveal the relation between the mechanical properties of the composite and that of each individual component, finite element analysis (FEA) has usually been adopted. In this study, in order to predict the mechanical properties of hard coating on a soft polymer, the response of this coating system during nanoindentation was modelled. Various models, such as a viscoelastic model and fitting model, were adopted to analyse the indentation response of this coating system. By varying the substrate properties (i.e., Young’s modulus, viscoelasticity, and Poisson’s ratio), Young’s modulus, energy loss, and the viscoelastic model of the coating system were analysed, and how the mechanical properties of the substrate will affect the indentation response of the coating system was discussed.

Young's Modulus and Poisson's Ratio Estimation Based on PSO Constriction Factor Method Parameters Evaluation

2019 ◽  
Vol 9 (2) ◽  
pp. 33-46
Author(s):  
George Lucas Dias ◽  
Ricardo Rodrigues Magalhães ◽  
Danton Diego Ferreira ◽  
Bruno Henrique Groenner Barbosa
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Young’S Modulus ◽  
Cantilever Beam ◽  
Poisson’S Ratio ◽  
Inverse Analysis ◽  
Young's Modulus ◽  
Poisson's Ratio ◽  
Factor Method ◽  
Constriction Factor

The knowledge of materials' mechanical properties in design during product development phases is necessary to identify components and assembly problems. These are problems such as mechanical stresses and deformations which normally cause plastic deformation, early fatigue or even fracture. This article is aimed to use particle swarm optimization (PSO) and finite element inverse analysis to determine Young's Modulus and Poisson's ratio from a cantilever beam, manufactured in ASTM A36 steel, subjected to a load of 19.6 N applied to its free end. The cantilever beam was modeled and simulated using a commercial FEA software. Constriction Factor Method (PSO variation) was used and its parameters were analyzed in order to improve errors. PSO results indicated Young's Modulus and Poisson's ratio errors of around 1.9% and 0.4%, respectively, when compared to the original material properties. Improvement in the data convergence and a reduction in the number of PSO iterations was observed. This shows the potentiality of using PSO along with Finite Element Inverse Analysis for mechanical properties evaluation.

Sensitivity of lightweight deflectometer deflections to layer stiffness via finite element analysis

2015 ◽  
Vol 52 (7) ◽  
pp. 961-970 ◽  
Author(s):  
Christopher T. Senseney ◽  
Jacob Grasmick ◽  
Michael A. Mooney
Keyword(s):  
Finite Element ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Experimental Studies ◽  
Fe Model ◽  
Element Analysis ◽  
Soil System ◽  
Dynamic Finite Element ◽  
Back Calculation ◽  
Measurement Depth

A dynamic finite element (FE) model of lightweight deflectometer (LWD) loading on a two-layer soil system, validated with an analytical solution and experimental data, is presented. Peak dynamic FE vertical deflections can be substantially different (almost always smaller) than FE static deflections. The numerically simulated measurement depth of the LWD center sensor is found to be 2–2.5 times the plate diameter, deeper than other experimental studies. Using the FE model, we conduct a sensitivity analysis of peak vertical deflections to the top layer Young’s modulus and underlying Young’s modulus of two-layer systems. Peak deflections from the center sensor are found to be more sensitive to the top layer Young’s modulus while peak deflections at radial offsets are found to be more sensitive to the underlying layer Young’s modulus. Sensitivities of layer moduli to FE deflections offer guidance in selecting weighting factors for the inverse solver in an LWD back-calculation procedure.

Micromechanical Characterization of Gasb by Microbeam Deflecion and Using Nanoprobe and Finite Element Analysis

2003 ◽  
Vol 782 ◽  
Author(s):  
M. Ospina ◽  
S. R. Vangala ◽  
D. Yang ◽  
J. A. Sherwood ◽  
C. Sung ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Young’S Modulus ◽  
Gallium Antimonide ◽  
Young's Modulus ◽  
Elastic Behavior ◽  
Material System ◽  
Scaling Effects ◽  
Commercial Development ◽  
Linear Elastic

ABSTRACTThe commercial development of low-power electronics and electro-optics based on antimonides demands a better understanding of the mechanical properties of ternary and quaternary thin-film alloys fabricated from the InGaAlAsSbP material system. Of particular importance is the determination of Young's modulus of these materials. In this paper, a technique for studying the mechanical behavior of these thin films was developed by using microbeam bending and finite element modeling. The technique was successfully applied to investigate the mechanical properties of GaSb. A test structure consisting of an array of gallium antimonide microbeams was fabricated with lengths ranging from 50 to 500 μm long. The microbeams were deflected using a calibrated nanoprobe, thereby generating load-displacement curves. Young's modulus was then extracted from the data using beam bending theory and a finite element simulation of the structures under load. A total of five microbeams with the same trapezoidal cross-section and lengths of 80, 85, 200, 250 and 500 μm were tested to study the technique applicability and size scaling effects on the mechanical properties. It was observed that the 80 and 85 μm beams exhibited linear elastic behavior and the 200, 250, and 500 μm microbeams exhibited non-linear elastic behavior.

Influence of Experimental Protocols on the Mechanical Properties of the Intervertebral Disc in Unconfined Compression

2011 ◽  
Vol 133 (7) ◽  
Author(s):  
Maximilien Recuerda ◽  
Simon-Pierre Coté ◽  
Isabelle Villemure ◽  
Delphine Périé
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Nucleus Pulposus ◽  
Annulus Fibrosus ◽  
Young's Modulus ◽  
Viscoelastic Model ◽  
Compression Tests ◽  
Unconfined Compression ◽  
Experimental Conditions ◽  
Experimental Protocols

The lack of standardization in experimental protocols for unconfined compression tests of intervertebral discs (IVD) tissues is a major issue in the quantification of their mechanical properties. Our hypothesis is that the experimental protocols influence the mechanical properties of both annulus fibrosus and nucleus pulposus. IVD extracted from bovine tails were tested in unconfined compression stress-relaxation experiments according to six different protocols, where for each protocol, the initial swelling of the samples and the applied preload were different. The Young’s modulus was calculated from a viscoelastic model, and the permeability from a linear biphasic poroviscoelastic model. Important differences were observed in the prediction of the mechanical properties of the IVD according to the initial experimental conditions, in agreement with our hypothesis. The protocol including an initial swelling, a 5% strain preload, and a 5% strain ramp is the most relevant protocol to test the annulus fibrosus in unconfined compression, and provides a permeability of 5.0 ± 4.2e−14m4/N·s and a Young’s modulus of 7.6 ± 4.7 kPa. The protocol with semi confined swelling and a 5% strain ramp is the most relevant protocol for the nucleus pulposus and provides a permeability of 10.7 ± 3.1 e−14m4/N·s and a Young’s modulus of 6.0 ± 2.5 kPa.

scholarly journals Influence of Degradation Products on the Elastic Stiffness Properties of Porous Absorbable Scaffolds Made From Bioabsorbable Metals

2021 ◽  
Author(s):  
Jannik Bühring ◽  
Maximilian Voshage ◽  
Johannes Heinrich Schleifenbaum ◽  
Holger Jahr ◽  
Kai-Uwe Schröder
Keyword(s):  
Finite Element ◽  
Young’S Modulus ◽  
Degradation Products ◽  
Young's Modulus ◽  
Element Model ◽  
Elastic Stiffness ◽  
Porous Scaffolds ◽  
Compression Tests ◽  
Substrate Layer ◽  
Stiffness Properties

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

scholarly journals Influence of Degradation Product Thickness on the Elastic Stiffness of Porous Absorbable Scaffolds Made from an Bioabsorbable Zn–Mg Alloy

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6027
Author(s):  
Jannik Bühring ◽  
Maximilian Voshage ◽  
Johannes Henrich Schleifenbaum ◽  
Holger Jahr ◽  
Kai-Uwe Schröder
Keyword(s):  
Finite Element ◽  
Young’S Modulus ◽  
Degradation Products ◽  
Young's Modulus ◽  
Element Model ◽  
Elastic Stiffness ◽  
Porous Scaffolds ◽  
Compression Tests ◽  
Young’S Moduli ◽  
Substrate Layer

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals such as magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone-equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For magnesium-based scaffolds during the first days an increase of the smeared Young’s modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the strut surfaces. In this study, the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite-element simulations are performed to study the influence of the substrate layer thickness and Young’s modulus for single struts and for a new scaffold geometry with adapted polar cubic face-centered unit cells with vertical struts (f2cc,z). The finite-element model is further validated by compression tests on AM scaffolds made from Zn1Mg (1 wt% Mg). The results show that even low thicknesses and Young’s moduli of the substrate layer significantly increases the smeared Young’s modulus under axial compression.

Evaluation of Mechanical Properties of Single-Walled Carbon Nanotubes

2011 ◽  
Vol 694 ◽  
pp. 12-16 ◽  
Author(s):  
Shiuh Chuan Her ◽  
Shou Jan Liu
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Young’S Modulus ◽  
Ultimate Strength ◽  
Young's Modulus ◽  
Single Walled Carbon Nanotubes ◽  
Frame Structure ◽  
Fe Model ◽  
Single Walled Carbon ◽  
Walled Carbon Nanotubes

A micromechanical finite element model incorporated with molecular mechanics is employed to determine the mechanical properties of single-walled carbon nanotubes (SWCNT). The SWCNT is modelled as a space-frame structure. The bonds between the carbon atoms are simulated as beam members to carry the loads, while the carbon atoms are the joints of the members. The modified Morse potential is adopted to characterize the non-linear behavior of C-C bonds. In this work, the mechanical properties of SWCNT such as the Young’s modulus, ultimate strength and strain are investigated. To verify the proposed FE model and evaluate its performance, the effects of diameter and chirality on the mechanical properties of SWCNT are presented. It is found that both the Young’s modulus and ultimate strength of SWCNT increase monotonically with the increase of diameter. The Young’s modulus of armchair is larger than that of zigzag SWCNTs. These results are in good agreement with the existing numerical and experimental results.

scholarly journals Modelling of Nanoindentation of TiAlN and TiN Thin Film Coatings for Automotive Bearing

2019 ◽  
Vol 8 (3) ◽  
pp. 7194-7199
Keyword(s):  
Mechanical Properties ◽  
Finite Element Method ◽  
Finite Element ◽  
Yield Strength ◽  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Poisson's Ratio ◽  
The Finite Element Method ◽  
Element Method

Bearings are critical components for the transmission of motion in machines. Automotive components, especially bearings, will wear out over a certain period of time because they are constantly subjected to high levels of stress and friction. Studies have proven that coatings can extend the lifespan of bearings. Hence, it is necessary to conduct studies on coatings for bearings, particularly the mechanical and wear properties of the coating material. This detailed study focused on the mechanical properties of single-coatings of TiN and TiAIN using the finite element method (FEM). The mechanical properties that can be obtained from nano-indentation experiments are confined to just the Young’s modulus and hardness. Therefore, nanoindentation simulations were conducted together with the finite element method to obtain more comprehensive mechanical properties such as the yield strength and Poisson’s ratio. In addition, various coating materials could be examined by means of these nanoindentation simulations, as well the effects of those parameters that could not be controlled experimentally, such as the geometry of the indenter and the bonding between the coating and the substrate. The simulations were carried out using the ANSYS Mechanical APDL software. The mechanical properties such as the Young’s modulus, yield strength, Poisson’s ratio and tangent modulus were 370 GPa, 19 GPa, 0.21 and 10 GPa, respectively for the TiAlN coating and 460 GPa, 14 GPa, 0.25 and 8 GPa, respectively for the TiN coating. The difference between the mechanical properties obtained from the simulations and experiments was less than 5 %.

Sign in / Sign up

Export Citation Format

Share Document