scholarly journals Potentiostatic Deposition and Characterization of Cuprous Oxide Thin Films

2013 ◽  
Vol 2013 ◽  
pp. 1-4 ◽  
Author(s):  
A. El-Shaer ◽  
A. R. Abdelwahed
Keyword(s):  
Thin Films ◽  
Cuprous Oxide ◽  
Deposition Time ◽  
Optical Quality ◽  
Electrodeposition Technique ◽  
Transparent Conducting ◽  
Cupric Acetate ◽  
Potentiostatic Deposition

Electrodeposition technique was employed to deposit cuprous oxide Cu2O thin films. In this work, Cu2O thin films have been grown on fluorine doped tin oxide (FTO) transparent conducting glass as a substrate by potentiostatic deposition of cupric acetate. The effect of deposition time on the morphologies, crystalline, and optical quality of Cu2O thin films was investigated.

scholarly journals Growth and Characterization of Epsomite Single Crystals Doped with KCl from low Temperature Aqueous Solutions

1970 ◽  
Vol 33 (1) ◽  
pp. 47-54 ◽  
Author(s):  
S Ferdous ◽  
J Podder
Keyword(s):  
Aqueous Solutions ◽  
Single Crystals ◽  
Optical Quality ◽  
Dielectric Studies ◽  
Slow Cooling ◽  
Large Size ◽  
Isothermal Evaporation ◽  
Academy Of Sciences

Highly transparent and well faceted large size epsomite single crystals have been grown in pure form and doped with KCl from aqueous solutions by slow cooling and isothermal evaporation method. The optical quality of the epsomite improves on doping by KCl. Mass growth rates were found to increase with doping of lower concentrations of KCl and then decreases with the higher concentration of KCl. KCl doped epsomite crystal reveals that structures are slightly distorted due to adsorption of Cl- ion into the crystal lattice. DC conductivity along the growth axis for all of the grown crystals increases with temperature in the range of 25 to 70ºC and also increases with the KCl concentration. Dielectric constant is found to be almost independent of frequency up to range of 106Hz. The dielectric studies show the suitability of these grown crystals for optoelectronic applications. DOI: 10.3329/jbas.v33i1.2949 Journal of Bangladesh Academy of Sciences, Vol. 33, No. 1, 47-54, 2009

Photoluminescence Characterization of SiGe/Si Quantum-Well Wire Structures

1995 ◽  
Vol 379 ◽  
Author(s):  
S. Nilsson ◽  
H. P. Zeindl ◽  
A. Wolff ◽  
K. Pressel
Keyword(s):  
Quantum Well ◽  
Room Temperature ◽  
Molecular Beam ◽  
Optical Quality ◽  
Photoluminescence Spectra ◽  
Single Quantum Well ◽  
Quantum Well Wire ◽  
Carbon Interstitial

ABSTRACTLow-temperature photoluminescence measurements were performed in order to probe the optical quality of SiGe/Si quantum-well wire structures fabricated by electron-beam lithography and subsequent reactive ion etching, having the patterned polymethylmethacrylate resist as an etch mask. In addition, one set of quantum-well wire structures was post-treated by means of annealing in a hydrogen environment. Our results show that even for the smallest wires of about 100nm in width, the wires exhibit phonon-resolved photoluminescence spectra, similar to that from the molecular beam eptitaxially grown SiGe single quantum well which was used as starting material for the patterning process. After the patterning process a new sharp peak appears in the photoluminescence spectra at 0.97eV in photon energy. Our investigation suggests that this feature is introduced by damage during the patterning process and most probably identical to the G-line, which previously was identified as originating from the dicarbon centre (substitutional carbon-interstitial carbon) in Si. This centre is known to be a very common endproduct of irradiating Si near room temperature which is the case at our patterning process.

Characterization of Transparent Conducting Al-Doped ZnO Thin Films and Device Applications

2007 ◽  
Vol 51 (12) ◽  
pp. 79 ◽  
Author(s):  
Sang Hern LEE ◽  
Young Moon YU ◽  
Tae Hoon KIM ◽  
Se-Young JEONG
Keyword(s):  
Thin Films ◽  
Zno Thin Films ◽  
Transparent Conducting ◽  
Device Applications ◽  
Doped Zno

scholarly journals Characterization of Cobalt Sulfide Thin Films Synthesized from Acidic Chemical Baths

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Tizazu Abza ◽  
Dereje Gelanu Dadi ◽  
Fekadu Gashaw Hone ◽  
Tesfaye Chebelew Meharu ◽  
Gebremeskel Tekle ◽  
...  
Keyword(s):  
Thin Films ◽  
Crystallite Size ◽  
Deposition Time ◽  
Average Crystallite Size ◽  
Cobalt Sulfide ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Electron Microscopic ◽  
Face Centered

Cobalt sulfide thin films were synthesized from acidic chemical baths by varying the deposition time. The powder X-ray diffraction studies indicated that there are hexagonal CoS, face-centered cubic Co3S4, and cubic Co9S8 phases of cobalt sulfide. The crystallite size of the hexagonal CoS phase decreased from 52.8 nm to 22.5 nm and that of the cubic Co9S8 phase increased from 11 nm to 60 nm as the deposition time increased from 2 hrs to 3.5 hrs. The scanning electron microscopic images revealed crack and pinhole free thin films with uniform and smooth background and few large polygonal grains on the surface. The band gap of the cobalt sulfide thin films decreased from 1.75 eV to 1.3 eV as the deposition time increased from 2 hrs to 3.5 hrs. The photoluminescence (PL) spectra of the films confirmed the emission of ultraviolet, violet, and blue lights. The intense PL emission of violet light at 384 nm had red shifted with increasing deposition time that could be resulted from the increase in the average crystallite size. The FTIR spectra of the films indicated the presence of OH, C-O-H, C-O, double sulfide, and Co-S groups. As the deposition time increased, the electrical resistivity of the cobalt sulfide thin films decreased due to the increase in both the crystallite size and the films’ thickness.

Detection, identification and mapping of cyanobacteria — Using remote sensing to measure the optical quality of turbid inland waters

1994 ◽  
Vol 45 (5) ◽  
pp. 801 ◽  
Author(s):  
DLB Jupp ◽  
JTO Kirk ◽  
GP Harris
Keyword(s):  
Remote Sensing ◽  
Algal Species ◽  
Optical Quality ◽  
High Spectral Resolution ◽  
Turbid Waters ◽  
Eastern Australia ◽  
Processing Techniques ◽  
Compact Airborne Spectrographic Imager

The advantages of airborne scanning for the detection, identification and mapping of algal species, cyanobacteria and associated water parameters (such as turbidity) can be realized if current research outcomes are developed into operational methods based on images with high spectral resolution. Evidence for this has become available through data obtained recently in Australia from the Compact Airborne Spectrographic Imager. This paper shows how pigments associated with cyanobacteria are detectable, even in the very turbid waters typical of eastern Australia. It demonstrates how, if the waterbodies and their constituents can be characterized by a programme of field and laboratory measurement, current processing techniques and models allow the concentrations of different constituents (algae and particles) in the photic zone to be estimated and mapped. The challenge for operational remote sensing of optical water quality in Australia (and throughout the world) is seen to have two components. One is to provide an effective characterization of the target inland and adjacent coastal waters and the other is to streamline the data analysis to provide maps of water properties in the time and cost frameworks required for operational use.

scholarly journals Ultra-thin films for plasmonics: a technology overview

2015 ◽  
Vol 4 (3) ◽  
Author(s):  
Radu Malureanu ◽  
Andrei Lavrinenko
Keyword(s):  
Thin Films ◽  
Surface Roughness ◽  
Support Surface ◽  
New Materials ◽  
Infra Red ◽  
Plasmon Polaritons ◽  
Plasmon Propagation ◽  
Made In

AbstractUltra-thin films with low surface roughness that support surface plasmon-polaritons in the infra-red and visible ranges are needed in order to improve the performance of devices based on the manipulation of plasmon propagation. Increasing amount of efforts is made in order not only to improve the quality of the deposited layers but also to diminish their thickness and to find new materials that could be used in this field. In this review, we consider various thin films used in the field of plasmonics and metamaterials in the visible and IR range. We focus our presentation on technological issues of their deposition and reported characterization of film plasmonic performance.

Deposition and Characterization of Cuprous Oxide Thin Films by Direct Current Magnetron Sputtering

2015 ◽  
Vol 7 (11) ◽  
pp. 990-994
Author(s):  
V. Vignesh ◽  
R. Niveditha ◽  
R. Nirmala ◽  
R.T. Rajendrakumar ◽  
R. Navamathavan
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Direct Current ◽  
Cuprous Oxide ◽  
Oxide Thin Films ◽  
Direct Current Magnetron Sputtering

Preparation and Characterization of Transparent Conducting Mn and Ni-Doped Zinc Oxide Films Prepared by Successive Ionic Layer Adsorption and Reaction Method

2020 ◽  
Vol 15 (1) ◽  
pp. 101-107
Author(s):  
M. Karunakaran ◽  
L. Bruno Chandrasekar ◽  
K. Kasirajan ◽  
R. Chandramohan
Keyword(s):  
Thin Films ◽  
Transparent Conducting Oxide ◽  
Hexagonal Structure ◽  
Silar Method ◽  
Texture Coefficients ◽  
Transparent Conducting ◽  
Doped Zno ◽  
Diffraction Patterns ◽  
Metal Doped

This paper reported the preparation and characterization of transparent conducting oxide thin films. Undoped and doped ZnO thin films were prepared by SILAR method. The micro-structural and optical properties were investigated. X-ray diffraction patterns revealed that the prepared thin films are polycrystalline in nature and has a hexagonal structure. The micro-structural properties of prepared thin films were calculated and crystallite size tends to changes due to dopant. The texture coefficients have been evaluated and found to be greater than unity revealing high texturing of the film. Undoped and Mn-doped ZnO prefer the orientation of (002) but Ni-doped ZnO and Mn and Ni co-doped ZnO prefers (100) orientation. The transmittance spectra of pure and transition metal-doped films were plotted against UV-Vis-NIR region and found that the transmittance changes with dopant and nature of doping. The optical band gap values were found to be in the range of 3.00–3.39 eV. The optical constants such as extinction coefficient, refractive index, dielectric constant and optical conductivity were examined.

Sign in / Sign up

Export Citation Format

Share Document