scholarly journals Robot Calibration for Cooperative Process under Typical Installation

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Yahui Gan ◽  
Xianzhong Dai ◽  
Donghui Dong
Keyword(s):  
Industrial Robot ◽  
Industrial Process ◽  
Industrial Robots ◽  
Cooperative Robots ◽  
Robot Calibration ◽  
Contact Points ◽  
Calibration Problem ◽  
Operation Procedure ◽  
Cooperative Process ◽  
Easy Operation

A method with easy operation procedure and simple calibration condition is presented in this paper to solve the base frame calibration problem for cooperative robots. It is carried out through constructing a series of handclasp configurations and recording coordinates of the contact points, respectively, in base frame of each robot. Then the rotation matrix and translation matrix between base frame of cooperative robots can be calculated which is just the calibration result for cooperative robots. Based on typical installation mode for industrial robot, the floor mounted, wall mounted and ceiling mounted, constraints between base frames of these robots are further explored. These constraints are used to improve the calibration results for base frame calibration problem. In order to validate the correctness and effectiveness of our method, experiments on two industrial robots (Motoman VA1400 and HP20) are carried out at the end of the paper. The calibration errors are less than 8 mm in most cases, which satisfies the requirement of positioning accuracy for most industrial process, such as arc welding, transporting, and cutting. These experiment results assert the correctness of our method which can be used effectively to solve the base frame calibration problem for cooperative robots in manufacturing process.

Study of Neural-Kinematics Architectures for Model-Less Calibration of Industrial Robots

2021 ◽  
Vol 33 (1) ◽  
pp. 158-171
Author(s):  
Monica Tiboni ◽  
◽  
Giovanni Legnani ◽  
Nicola Pellegrini
Keyword(s):  
Degrees Of Freedom ◽  
Industrial Robot ◽  
Kinematic Model ◽  
Back Propagation ◽  
Simulated Data ◽  
Industrial Robots ◽  
Robot Calibration ◽  
Feed Forward Neural Network ◽  
Comparative Performance ◽  
Order Of Magnitude

Modeless industrial robot calibration plays an important role in the increasing employment of robots in industry. This approach allows to develop a procedure able to compensate the pose errors without complex parametric model. The paper presents a study aimed at comparing neural-kinematic (N-K) architectures for a modeless non-parametric robotic calibration. A multilayer perceptron feed-forward neural network, trained in a supervised manner with the back-propagation learning technique, is coupled in different modes with the ideal kinematic model of the robot. A comparative performance analysis of different neural-kinematic architectures was executed on a two degrees of freedom SCARA manipulator, for direct and inverse kinematics. Afterward the optimal schemes have been identified and further tested on a three degrees of freedom full SCARA robot and on a Stewart platform. The analysis on simulated data shows that the accuracy of the robot pose can be improved by an order of magnitude after compensation.

scholarly journals A Methodology for Industrial Robot Calibration Based on Measurement Sub-Regions

2021 ◽  
Author(s):  
Juan Sebastian Toquica ◽  
José Maurı́cio Motta
Keyword(s):  
Industrial Robot ◽  
Low Cost ◽  
Kinematic Model ◽  
Measurement Data ◽  
Industrial Applications ◽  
Industrial Robots ◽  
Robot Calibration ◽  
High Precision Measurement ◽  
Measurement Systems ◽  
Robot Accuracy

Abstract This paper proposes a methodology for calibration of industrial robots that uses a concept of measurement sub-regions, allowing low-cost solutions and easy implementation to meet the robot accuracy requirements in industrial applications. The solutions to increasing the accuracy of robots today have high-cost implementation, making calibration throughout the workplace in industry a difficult and unlikely task. Thus, reducing the time spent and the measured workspace volume of the robot end-effector are the main benefits of the implementation of the sub-region concept, ensuring sufficient flexibility in the measurement step of robot calibration procedures. The main contribution of this article is the proposal and discussion of a methodology to calibrate robots using several small measurement sub-regions and gathering the measurement data in a way equivalent to the measurements made in large volume regions, making feasible the use of high-precision measurement systems but limited to small volumes, such as vision-based measurement systems. The robot calibration procedures were simulated according to the literature, such that results from simulation are free from errors due to experimental setups as to isolate the benefits of the measurement proposal methodology. In addition, a method to validate the analytical off-line kinematic model of industrial robots is proposed using the nominal model of the robot supplier incorporated into its controller.

High precise and zero-cost solution for fully automatic industrial robot TCP calibration

2019 ◽  
Vol 46 (5) ◽  
pp. 650-659
Author(s):  
Mustafa Cakir ◽  
Cengiz Deniz
Keyword(s):  
Fixed Point ◽  
Measuring Equipment ◽  
Industrial Robot ◽  
Absolute Calibration ◽  
Robot Calibration ◽  
Special Equipment ◽  
Content Type ◽  
Robot Controller ◽  
Contact Points ◽  
Plane Plate

Purpose The purpose of this study is to present a novel method for industrial robot TCP (tool center point) calibration. The proposed method offers fully automated robot TCP calibration within a defined cycle time. The method is applicable for large-scale installations due to its zero cost for each robot. Design/methodology/approach Precise and expensive measuring equipment or specially designed reference devices are required for robot calibration. The calibration can be performed by using only one plane plate in this method, and the calibration procedure is defined step by step: the robot moves to the target plane position. Then, the TCP touches the plane and the actual robot configuration is recorded. Then robot moves back into position and the same step is repeated for a new sample. Alternatively, the robot can be stationary and the plane can be moved towards the robot TCP. TCP is calculated by processing the difference of the contact points recorded at different positions. The process is fully automated. No special equipment is used. The calculations are very simple, and the robot controller can easily be realized. Findings The conventional manual robot TCP calibration process takes about 15 min and takes more time in case of the high accuracy. The proposed method reduces this time to less than 3 min without operator support. Practical tests have shown that TCP calibration can be performed with 0.1-0.6 mm of accuracy. This solution is an automated process and does not require special installation and it also has approximately zero cost. For this reason, this study recommends using the proposed solution widely in areas where even one or hundreds of robots are located. Research limitations/implications In this study, the data were directly taken from the robot controller without using any special measuring equipment. The industrial robot used in the tests has no absolute calibration. The classical “four-point method” was used for reference TCP data. It is the initial acceptance that this process conducted with extreme care and by using a needle-tipped tool will not produce exact values. It was observed that deviation of the TCP from a fixed point in reorient motions was not more than 0.5 mm. This method has been validated for different bits. The pilot works for different robot applications in Ford Otosan Gölcük Plant have been completed and dissemination has started. Originality/value Although the approach uses is clear and simple, it is surprising that the calculation of TCP using plane equations has so far not been mentioned in the literature. The disadvantage of using either fixed point or sphere as a reference is that the TCP cannot automatically guide to the target. This problem was overcome with the use of a larger target plane plate and the process was fully automated. The proposed method can be widely used in practical applications.

SAFETY AND RISK ASSESSMENT AT AUTOMATED WORKPLACE

2018 ◽  
pp. 78-84
Author(s):  
Marek Vagas
Keyword(s):  
Risk Assessment ◽  
Industrial Robot ◽  
Industrial Robots ◽  
Added Value ◽  
Growing Up ◽  
Target Setting ◽  
Clear View ◽  
General Safety

Urgency of the research. Automated workplaces are growing up in present, especially with implementation of industrial robots with feasibility of various dispositions, where safety and risk assessment is considered as most important issues. Target setting. The protection of workers must be at the first place, therefore safety and risk assessment at automated workplaces is most important problematic, which had presented in this article Actual scientific researches and issues analysis. Actual research is much more focused at standard workplaces without industrial robots. So, missing of information from the field of automated workplaces in connection with various dispositions can be considered as added value of article. Uninvestigated parts of general matters defining. Despite to lot of general safety instructions in this area, still is missed clear view only at automated workplace with industrial robots. The research objective. The aim of article is to provide general instructions directly from the field of automated workplaces The statement of basic materials. For success realization of automated workplace is good to have a helping hand and orientation requirements needed for risk assessment at the workplace. Conclusions. The results published in this article increase the awareness and information of such automated workplaces, together with industrial robots. In addition, presented general steps and requirements helps persons for better realization of these types of workplaces, where major role takes an industrial robot. Our proposed solution can be considered as relevant base for risk assessment such workplaces with safety fences or light barriers.

A Polishing Robot Force Control System Based on Time Series Data in Industrial Internet of Things

2021 ◽  
Vol 21 (2) ◽  
pp. 1-22
Author(s):  
Chen Zhang ◽  
Zhuo Tang ◽  
Kenli Li ◽  
Jianzhong Yang ◽  
Li Yang
Keyword(s):  
Time Series ◽  
Control System ◽  
Force Control ◽  
Time Series Data ◽  
Industrial Robot ◽  
Industrial Robots ◽  
Series Data ◽  
Industrial Internet Of Things ◽  
Industrial Internet ◽  
Force Control System

Installing a six-dimensional force/torque sensor on an industrial arm for force feedback is a common robotic force control strategy. However, because of the high price of force/torque sensors and the closedness of an industrial robot control system, this method is not convenient for industrial mass production applications. Various types of data generated by industrial robots during the polishing process can be saved, transmitted, and applied, benefiting from the growth of the industrial internet of things (IIoT). Therefore, we propose a constant force control system that combines an industrial robot control system and industrial robot offline programming software for a polishing robot based on IIoT time series data. The system mainly consists of four parts, which can achieve constant force polishing of industrial robots in mass production. (1) Data collection module. Install a six-dimensional force/torque sensor at a manipulator and collect the robot data (current series data, etc.) and sensor data (force/torque series data). (2) Data analysis module. Establish a relationship model based on variant long short-term memory which we propose between current time series data of the polishing manipulator and data of the force sensor. (3) Data prediction module. A large number of sensorless polishing robots of the same type can utilize that model to predict force time series. (4) Trajectory optimization module. The polishing trajectories can be adjusted according to the prediction sequences. The experiments verified that the relational model we proposed has an accurate prediction, small error, and a manipulator taking advantage of this method has a better polishing effect.

scholarly journals Comparative Analysis of the Life-Cycle Cost of Robot Substitution: A Case of Automobile Welding Production in China

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 226
Author(s):  
Xuyang Zhao ◽  
Cisheng Wu ◽  
Duanyong Liu
Keyword(s):  
Life Cycle ◽  
Systems Engineering ◽  
Life Cycle Cost ◽  
Manufacturing Systems ◽  
Large Scale ◽  
Cost Allocation ◽  
Industrial Robot ◽  
Case Analysis ◽  
Industrial Robots ◽  
Analysis Model

Within the context of the large-scale application of industrial robots, methods of analyzing the life-cycle cost (LCC) of industrial robot production have shown considerable developments, but there remains a lack of methods that allow for the examination of robot substitution. Taking inspiration from the symmetry philosophy in manufacturing systems engineering, this article further establishes a comparative LCC analysis model to compare the LCC of the industrial robot production with traditional production at the same time. This model introduces intangible costs (covering idle loss, efficiency loss and defect loss) to supplement the actual costs and comprehensively uses various methods for cost allocation and variable estimation to conduct total cost and the cost efficiency analysis, together with hierarchical decomposition and dynamic comparison. To demonstrate the model, an investigation of a Chinese automobile manufacturer is provided to compare the LCC of welding robot production with that of manual welding production; methods of case analysis and simulation are combined, and a thorough comparison is done with related existing works to show the validity of this framework. In accordance with this study, a simple template is developed to support the decision-making analysis of the application and cost management of industrial robots. In addition, the case analysis and simulations can provide references for enterprises in emerging markets in relation to robot substitution.

scholarly journals Research of Calibration Method for Industrial Robot Based on Error Model of Position

2021 ◽  
Vol 11 (3) ◽  
pp. 1287
Author(s):  
Tianyan Chen ◽  
Jinsong Lin ◽  
Deyu Wu ◽  
Haibin Wu
Keyword(s):  
Coordinate System ◽  
Industrial Robot ◽  
Calibration Method ◽  
Error Model ◽  
Position Error ◽  
Industrial Robots ◽  
Positioning Error ◽  
Robot Position ◽  
General Measurement ◽  
Parameter Error

Based on the current situation of high precision and comparatively low APA (absolute positioning accuracy) in industrial robots, a calibration method to enhance the APA of industrial robots is proposed. In view of the "hidden" characteristics of the RBCS (robot base coordinate system) and the FCS (flange coordinate system) in the measurement process, a comparatively general measurement and calibration method of the RBCS and the FCS is proposed, and the source of the robot terminal position error is classified into three aspects: positioning error of industrial RBCS, kinematics parameter error of manipulator, and positioning error of industrial robot end FCS. The robot position error model is established, and the relation equation of the robot end position error and the industrial robot model parameter error is deduced. By solving the equation, the parameter error identification and the supplementary results are obtained, and the method of compensating the error by using the robot joint angle is realized. The Leica laser tracker is used to verify the calibration method on ABB IRB120 industrial robot. The experimental results show that the calibration method can effectively enhance the APA of the robot.

scholarly journals Fault diagnosis of industrial robot reducer by an extreme learning machine with a level-based learning swarm optimizer

2021 ◽  
Vol 13 (5) ◽  
pp. 168781402110195
Author(s):  
Jianwen Guo ◽  
Xiaoyan Li ◽  
Zhenpeng Lao ◽  
Yandong Luo ◽  
Jiapeng Wu ◽  
...  
Keyword(s):  
Fault Diagnosis ◽  
Extreme Learning Machine ◽  
Large Scale ◽  
Production Efficiency ◽  
Industrial Robot ◽  
Optimal Solution ◽  
Industrial Robots ◽  
Generalization Performance ◽  
Gradient Descent Algorithm ◽  
Learning Machine

Fault diagnosis is of great significance to improve the production efficiency and accuracy of industrial robots. Compared with the traditional gradient descent algorithm, the extreme learning machine (ELM) has the advantage of fast computing speed, but the input weights and the hidden node biases that are obtained at random affects the accuracy and generalization performance of ELM. However, the level-based learning swarm optimizer algorithm (LLSO) can quickly and effectively find the global optimal solution of large-scale problems, and can be used to solve the optimal combination of large-scale input weights and hidden biases in ELM. This paper proposes an extreme learning machine with a level-based learning swarm optimizer (LLSO-ELM) for fault diagnosis of industrial robot RV reducer. The model is tested by combining the attitude data of reducer gear under different fault modes. Compared with ELM, the experimental results show that this method has good stability and generalization performance.

Finding Features of Positioning Error for Large Industrial Robots Based on Convolutional Neural Network

2021 ◽  
Author(s):  
Daiki Kato ◽  
Kenya Yoshitugu ◽  
Naoki Maeda ◽  
Toshiki Hirogaki ◽  
Eiichi Aoyama ◽  
...  
Keyword(s):  
Neural Network ◽  
Convolutional Neural Network ◽  
Production Systems ◽  
Industrial Robot ◽  
Three Dimensional ◽  
Industrial Robots ◽  
Numerical Control ◽  
Robot Motion ◽  
Positioning Error ◽  
End Effector

Abstract Most industrial robots are taught using the teaching playback method; therefore, they are unsuitable for use in variable production systems. Although offline teaching methods have been developed, they have not been practiced because of the low accuracy of the position and posture of the end-effector. Therefore, many studies have attempted to calibrate the position and posture but have not reached a practical level, as such methods consider the joint angle when the robot is stationary rather than the features during robot motion. Currently, it is easy to obtain servo information under numerical control operations owing to the Internet of Things technologies. In this study, we propose a method for obtaining servo information during robot motion and converting it into images to find features using a convolutional neural network (CNN). Herein, a large industrial robot was used. The three-dimensional coordinates of the end-effector were obtained using a laser tracker. The positioning error of the robot was accurately learned by the CNN. We extracted the features of the points where the positioning error was extremely large. By extracting the features of the X-axis positioning error using the CNN, the joint 1 current is a feature. This indicates that the vibration current in joint 1 is a factor in the X-axis positioning error.

Optimization of the Robot Calibration Process

1992 ◽  
Author(s):  
G. Zak ◽  
R. G. Fenton ◽  
B. Benhabib
Keyword(s):  
Optimization Problem ◽  
Kinematic Model ◽  
Optimization Procedure ◽  
Calibration Procedure ◽  
Residual Error ◽  
Industrial Robots ◽  
Multiple Objective Optimization ◽  
Robot Calibration ◽  
Calibration Process ◽  
The Cost

Abstract Most industrial robots cannot be off-line programmed to carry out a task accurately, unless their kinematic model is suitably corrected through a calibration procedure. However, proper calibration is an expensive and time-consuming procedure due to the highly accurate measurement equipment required and due to the significant amount of data that must be collected. To improve the efficiency of robot calibration, an optimization procedure is proposed in this paper. The objective of minimizing the cost of the calibration is combined with the objective of minimizing the residual error after calibration in one multiple-objective optimization. Prediction of the residual error for a given calibration process presents the main difficulty for implementing the optimization. It is proposed that the residual error is expressed as a polynomial function. This function is obtained as a result of fitting a response surface to either experimental or simulated sample estimates of the residual error. The optimization problem is then solved by identifying a reduced set of possible solutions, thus greatly simplifying the decision maker’s choice of an effective calibration procedure. An application example of this method is also included.

Sign in / Sign up

Export Citation Format

Share Document