Study on the aerodynamic noise of internal flow of regenerative flow compressors for a fuel-cell car

2013 ◽  
Vol 228 (7) ◽  
pp. 1155-1174 ◽  
Author(s):  
Qiang Kang ◽  
Shuguang Zuo ◽  
Kaijun Wei
Keyword(s):  
Finite Element ◽  
Fuel Cell ◽  
Dynamic Model ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Internal Flow ◽  
Aerodynamic Noise ◽  
Noise Sources ◽  
Element Analysis ◽  
Regenerative Flow

The regenerative flow compressor used in fuel-cell cars generates high aerodynamic noise, which is the main source of noise. Compared with the research on centrifugal or axial turbomachinery, research on the noise of regenerative flow compressors is far from adequate. This paper presents the on-going work on it at Tongji University based on both experimental and computational works. In this study, a three-dimensional unsteady computational fluid dynamic model of the compressor was constructed with the large eddy approach. The pressure fluctuation, vortex noise source and Ffowcs William-Hawkings (FW-H) method were used to analyze the characteristics of the aerodynamic noise sources. Additionally, the far-field aerodynamic noise generated by the internal flow of the compressor was predicted using the aeroacoustic finite element method. The simulation results were validated with the experimental data. It was found that combining the fluid dynamic model and aeroacoustic finite element analysis promising results for aerodynamic noise prediction of compressors could be produced. The effects of the impeller parameters on the aerodynamic noise of the compressor were also studied.

Direct Strength Analysis of Semi-Submersible Platform Structures

2004 ◽  
Author(s):  
Haibin Zhang ◽  
Huilong Ren ◽  
Yangshan Dai
Keyword(s):  
Finite Element ◽  
Interpolation Method ◽  
Fluid Dynamic ◽  
Dynamic Pressure ◽  
Three Dimensional ◽  
Element Model ◽  
Strength Analysis ◽  
Wave Load ◽  
Element Analysis ◽  
Wet Surface

A kind of direct strength analysis method of semi-submersible platform structures is presented in this paper. With the differences in shape of pontoon, column and beam being considered, the method of accumulative chord length cubic parameter spline function combined with analytic expression is adopted to generate the mesh of platform wet surface. The hydrodynamic coefficients of the platform are calculated by the three-dimensional potential flow theory of the linear hydrodynamic problem for platforms with low forward speed. The equations of platform motions are established and solved in frequency domain, and the responses of wave-induced loads on the platforms are calculated. According to the mesh of hydrodynamic computation, the fluid dynamic pressure field of platform wet surface is built, and the pressure loads on shell elements in the finite element model of the structure are calculated by the interpolation method. The calculation conditions and loads in the finite element analysis (FEA) of the platform structures are determined according to the design wave analysis approach. A computer program based on this method has been developed, and a calculation example of semi-submersible platform is illustrated. Analysis results show that this method is a satisfying approach for wave load computation and direct strength analysis of the semi-submersible platforms.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Modeling for Steel Cord Analysis in Radial Tires

2013 ◽  
Vol 41 (1) ◽  
pp. 60-79 ◽  
Author(s):  
Wei Yintao ◽  
Luo Yiwen ◽  
Miao Yiming ◽  
Chai Delong ◽  
Feng Xijin
Keyword(s):  
Finite Element ◽  
High Efficiency ◽  
Force Measurement ◽  
Three Dimensional ◽  
Local Stress ◽  
Tension Force ◽  
Center Line ◽  
Element Analysis ◽  
Design Variables ◽  
Steel Cord

ABSTRACT: This article focuses on steel cord deformation and force investigation within heavy-duty radial tires. Typical bending deformation and tension force distributions of steel reinforcement within a truck bus radial (TBR) tire have been obtained, and they provide useful input for the local scale modeling of the steel cord. The three-dimensional carpet plots of the cord force distribution within a TBR tire are presented. The carcass-bending curvature is derived from the deformation of the carcass center line. A high-efficiency modeling approach for layered multistrand cord structures has been developed that uses cord design variables such as lay angle, lay length, and radius of the strand center line as input. Several types of steel cord have been modeled using the developed method as an example. The pure tension for two cords and the combined tension bending under various loading conditions relevant to tire deformation have been simulated by a finite element analysis (FEA). Good agreement has been found between experimental and FEA-determined tension force-displacement curves, and the characteristic structural and plastic deformation phases have been revealed by the FE simulation. Furthermore, some interesting local stress and deformation patterns under combined tension and bending are found that have not been previously reported. In addition, an experimental cord force measurement approach is included in this article.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Sign in / Sign up

Export Citation Format

Share Document