Experimental study of spray characteristics of biodiesel blending with diethyl carbonate in a common rail injection system

2017 ◽  
Vol 233 (2) ◽  
pp. 249-262 ◽  
Author(s):  
Wei Fu ◽  
Lanbo Song ◽  
Tao Liu ◽  
Qizhao Lin
Keyword(s):  
Cone Angle ◽  
Injection Pressure ◽  
Injection System ◽  
Diethyl Carbonate ◽  
Spray Characteristics ◽  
Projected Area ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Common Rail Injection System ◽  
Common Rail Injection

The objective of this paper is to investigate the spray macroscopic characteristics of biodiesel, diethyl carbonate (DEC)-biodiesel blends and diesel fuel based on a common-rail injection system. The spray tip penetration, spray cone angle and the spray projected area were measured through a high-speed photography method. The experimental results reveal that injection pressure and ambient pressure have significant effects on the spray characteristics. Higher injection pressure makes the spray tip penetration increase, while higher back pressure inside the chamber leads to the enlargement of the spray cone angle. The addition of DEC causes the blends fuels to have a shorter penetration and larger spray projected area, which reveals the potential capacity to improve the atomization process compared with biodiesel. The estimation of spray droplet size indicates that DEC30 generates a smaller Sauter mean diameter (SMD) because of its lower surface tension and viscosity. Model predictions were illustrated and compared with current work.

Investigation of the Influence of Injection Rate Shaping on the Spray Characteristics in a Diesel Common Rail System Equipped with a Piston Amplifier

2005 ◽  
Vol 127 (6) ◽  
pp. 1102-1110 ◽  
Author(s):  
J. Benajes ◽  
R. Payri ◽  
S. Molina ◽  
V. Soare
Keyword(s):  
Cone Angle ◽  
Injection Pressure ◽  
Injection Rate ◽  
Common Rail ◽  
Injection System ◽  
Common Rail System ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Common Rail Injection System ◽  
Common Rail Injection

The quality of the mixing process of fuel and air in a direct injection diesel engine relies heavily on the way the spray develops when injected into the combustion chamber. Among other factors, the spray development depends on the injection rate of the fuel delivered by the injector. The paper presents a study, at both a macroscopic and microscopic level, of a Diesel spray generated by a common-rail injection system featuring a piston pressure amplifier. By modifying the timing and the duration of the injector and amplifier piston actuation, it is possible to obtain high injection pressures up to 180MPa, and different shapes for the injection rate, which would not be achievable with a regular common rail injection system. The spray evolution produced by three different injection rate shapes (square, ramp, and boot) has been investigated in an injection test rig, by means of visualization and PDPA techniques, at different injection conditions. The main conclusions are the important effect on spray penetration of the initial injection rate evolution and the small influence of the maximum injection pressure attained at the end of the injection event. Smaller or even negligible effects have been found on the spray cone angle and on the droplet Sauter mean diameter.

scholarly journals Experimental Study of Spray Characteristics of Kerosene-Ethanol Blends from a Pressure-Swirl Nozzle

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Tao Zhang ◽  
Bo Dong ◽  
Xun Zhou ◽  
Linan Guan ◽  
Weizhong Li ◽  
...  
Keyword(s):  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Breakup Length ◽  
Ethanol Blends ◽  
Pressure Swirl ◽  
Spray Velocity

Partial replacement of kerosene by ethanol in a gas turbine is regarded as a good way to improve the spray quality and reduce the fossil energy consumption. The present work is aimed at studying the spray characteristics of kerosene-ethanol blends discharging from a pressure-swirl nozzle. The spray cone angle, discharge coefficient, breakup length, and velocity distribution are obtained by particle image velocimetry, while droplet size is acquired by particle/droplet imaging analysis. Kerosene, E10 (10% ethanol, 90% kerosene), E20 (20% ethanol, 80% kerosene), and E30 (30% ethanol, 70% kerosene) have been considered under the injection pressure of 0.1–1 MPa. The results show that as injection pressure is increased, the discharge coefficient and breakup length decrease, while the spray cone angle, drop size, and spray velocity increase. Meanwhile, the drop size decreases and the spray velocity increases with ethanol concentration when the injection pressure is lower than 0.8 MPa. However, the spray characteristics are not affected obviously by the ethanol concentration when the injection pressure exceeds 0.8 MPa. A relation to breakup length for kerosene-ethanol blends is obtained. The findings demonstrate that the adding of ethanol into kerosene can promote atomization performance.

Effect of Injection Parameters on the Spray Characteristics of DME Fuel

2006 ◽  
Author(s):  
Bong Woo Ryu ◽  
Seung Hwan Bang ◽  
Hyun Kyu Suh ◽  
Chang Sik Lee
Keyword(s):  
Dimethyl Ether ◽  
Diesel Fuel ◽  
Cone Angle ◽  
Injection Pressure ◽  
Injection Rate ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Injection Duration ◽  
Injection Parameters

The purpose of this study is to investigate the effect of injection parameters on the injection and spray characteristics of dimethyl ether and diesel fuel. In order to analyze the injection and spray characteristics of dimethyl ether and diesel fuel with employing high-pressure common-rail injection system, the injection characteristics such as injection delay, injection duration, and injection rate, spray cone angle and spray tip penetration was investigated by using the injection rate measuring system and the spray visualization system. In this work, the experiments of injection rate and spray visualization are performed at various injection parameters. It was found that injection quantity was decreased with the increase of injection pressure at the same energizing duration and injection pressure In the case of injection characteristics, dimethyl ether showed shorter of injection delay, longer injection duration and lower injected mass flow rate than diesel fuel in accordance with various energizing durations and injection pressures. Also, spray development of dimethyl ether had larger spray cone angle than that of diesel fuel at various injection pressures. Spray tip penetration was almost same development and tendency regardless of injection angles.

Experimental Study on Diesel Engine and Analysis the Spray Characteristics of Diesel and Biodiesel by Varying Injection Pressure

2014 ◽  
Vol 984-985 ◽  
pp. 932-937 ◽  
Author(s):  
Palani Raghu ◽  
M. Senthamil Selvan ◽  
K. Pitchandi ◽  
N. Nallusamy
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Weber Number ◽  
Direct Injection ◽  
Cone Angle ◽  
Injection Pressure ◽  
Injection Velocity ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone

— The spray characteristic of the injected fuel is mainly depends upon fuel injection pressure, temperature, ambient pressure, fuel viscosity and fuel density. An experimental study was conducted to examine the effect of injection pressure on the spray was injected into direct injection (DI) diesel engine in the atmospheric condition. In Diesel engine, the window of 20 mm diameter hole and the transparent quartz glass materials were used for visualizing spray characteristics of combustion chamber at right angle triangle position. The varying Injection pressure of 180 - 240 bar and the engine was hand cranked for conducting the experiments. Spray characteristics for Jatropha oil methyl ester (JOME) and diesel were studied experimentally. Spray tip penetration and spray cone angle were measured in a combustion chamber of Direct Injection diesel engine by employing high speed Digital camera using Mie Scattering Technique and ImageJ software. The study shows the JOME gives longer spray tip penetration and smaller spray cone angle than those of diesel fuels. The Spray breakup region (Reynolds number, Weber number), Injection velocity and Sauter Mean Diameter (SMD) were determined for diesel and JOME. SMD decreases for JOME than diesel and the Injection velocity, Reynolds Number, Weber Number Increases for JOME than diesel.

Experimental Study on Spray Characteristics of Diesel Engines and Analysis of Fuel Dripping Phenomenon

2014 ◽  
Vol 1078 ◽  
pp. 271-275 ◽  
Author(s):  
Yu Qiang Wu ◽  
Qian Wang ◽  
Zhi Sheng Gao ◽  
Zhou Rong Zhang ◽  
Li Ming Dai
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Cone Angle ◽  
Digital Camera ◽  
Injection Pressure ◽  
Fuel Mixture ◽  
Long Distance ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone

Experimental study on macroscopic spray characteristics of a certain type of domestic common rail injectors under the conditions of different injection pressures was carried out through a high-speed digital camera. Furthermore, a fuel dripping phenomenon at the end stage of injection was observed through the high-speed digital camera equipped with a long-distance microscope, and a further analysis of the phenomenon was made. The results show the increase in the injection pressure can evidently enhance spray cone angle and expand the scope of spray field in combustion chamber, which is conducive to air-fuel mixture. The spray cone angle during the development spray shows a double-peak shape. And the long response-time of seating of solenoid valve core that disables the injection cutting off in time is one of factors causing fuel dripping phenomenon.

Experimental Study on Spray Characteristics of N-Butanol/Acidic Oil/Diesel Blends

2014 ◽  
Vol 1008-1009 ◽  
pp. 1001-1005 ◽  
Author(s):  
Jian Wu ◽  
Yang Hua ◽  
Zhan Cheng Wang ◽  
Li Li Zhu ◽  
Wei Wei Shang
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Cone Angle ◽  
Injection Pressure ◽  
Air Entrainment ◽  
Mixing Ratio ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Spray Penetration

In order to better research on the spray characteristics of biodiesel and n-butanol blends, an experimental study of spray characteristics of different fuel mixtures was investigated in a constant volume vessel using high speed photograph method, and analyzed the influence of different proportions of acidic oil biodiesel and n-butanol on the macroscopic parameters of spray penetration, spray cone angle and so on. The results show that with the increase of acidic oil biodiesel ratio, the air entrainment is weakened, spray penetration gradually increases and spray cone angle decreases under the same injection pressure and back pressure. After adding n-butanol in acidic oil biodiesel and diesel mixture fuel, the surrounding air entrainment is enhanced, and spray front end widen. With the increase of mixing ratio, spray penetration increases first, then decreases. The spray cone angle increases after adding n-butanol, and decreases with the increase of mixing ratio. The results show that adding n-butanol can be used as one of the methods to improve biodiesel spray characteristics.

SPRAY VISUALIZATION OF HYDROTREATED VEGETABLE OIL UNDER SIMULATED DIESEL ENGINE CONDITION

2020 ◽  
Vol 40 (04) ◽  
Author(s):  
VO TAN CHAU
Keyword(s):  
Vegetable Oil ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Cone Angle ◽  
Injection Pressure ◽  
Fuel Properties ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Penetration Length ◽  
Spray Cone

The diversity of alternative fuels and the corresponding variation in their physical and chemical properties, coupled with simultaneous changes in advanced techniques for CI-engine, needed to improve engine efficiency and emissions. Hydrotreated Vegetable Oil (HVO), seen as a promising substitution for petrol-diesel, and diesel fuel (mixed of 7% palm-biodiesel or B7) were analyzed on fuel properties. Then, the influence of these fuel properties on spray characteristics in constant volume combustion chamber were evaluated under conditions of single hole injector of 200m diameter, injection pressure of 100MPa, constant back pressure of 4.0MPa and energizing time of 2.5ms. The results show that HVO had smaller in viscosity (18.48%), density (5.52%), sulfur content, distillation under T50, T90 and higher in derived cetane index (27.2%), heating value (2.2%), respectively, compared to diesel. Spray characteristics of HVO had the same propensity with diesel fuel. HVO revealed a slightly shorter in penetration length (5%) during fully developed zone, a larger spray cone angle (from 0.2 to 1.1 degree wider in quasi-steady state). Both fuels had a similar maximum spray velocity reaching at 5mm to 10mm from nozzle orifice. Also observed was an increase in spray volume of HVO.

Characteristics of Hollow Cone Swirl Spray at Various Nozzle Orifice Diameters

2012 ◽  
Vol 58 (2) ◽  
Author(s):  
A. Hussein ◽  
M. Hafiz ◽  
H. Rashid ◽  
A. Halim ◽  
W. Wisnoe ◽  
...  
Keyword(s):  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Orifice Diameter ◽  
Hollow Cone ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Nozzle Orifice ◽  
Breakup Length

An experimental work to investigate the swirl spray characteristics that emanates from hollow–cone and solid–cone spray simplex atomizers is presented. Main objective of the research is to investigate the spray characteristics, i.e. spray breakup length, discharge coefficient and spray cone angle at different nozzle orifice diameter and injection pressure. Discharge coefficient is almost uninfluenced by the operating Reynolds number. This test also reveals that both breakup length and spray cone angle increases as orifice diameter is increased. Higher injection pressure leads to shorter breakup length and wider spray cone angle.

scholarly journals Experimental Investigation on the Early Stage Spray Characteristics with Biodiesel and Diesel

2017 ◽  
Author(s):  
Shenghao Yu ◽  
Bifeng Yin ◽  
Shuai Wen ◽  
Xifeng Li ◽  
Hekun Jia ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Early Stage ◽  
Cone Angle ◽  
Injection Pressure ◽  
Mie Scattering ◽  
Scattering Method ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Spray Tip Penetration

The early stage spray characteristics have a great impact on the secondary atomization progress, and thus affectthe engine combustion and emission performances. The experimental investigation of the early stage spray behaviors with biodiesel and diesel was carried out by employing a laser-based Mie-scattering method. The results show that the spray tip penetration for biodiesel is higher than that for diesel at the early stage spray under the same injection pressure. Moreover, the early stage spray tip penetration can be longer under high injection pressures for two fuels. Besides, the early stage spray cone angle for biodiesel is narrower than that for diesel, and the spray cone angle is especially higher than biodiesel by 25.8% after start of injection time of 0.01ms. Furthermore, under the same injection condition, the difference of early stage spray area between diesel and biodiesel is not obvious, while the spray volume for biodiesel is larger than that for diesel, and also the sprayvolume can be enlarged by increasing injection pressure for both fuels.DOI: http://dx.doi.org/10.4995/ILASS2017.2017.4651

Experimental study of the effect of n-butanol additive on spray characteristics of biodiesel in a high-pressure common-rail injection system

2018 ◽  
Vol 233 (2) ◽  
pp. 211-220 ◽  
Author(s):  
Bolun Yi ◽  
Wei Fu ◽  
Lanbo Song ◽  
Fengyu Li ◽  
Tao Liu ◽  
...  
Keyword(s):  
High Speed ◽  
Cone Angle ◽  
Density Ratio ◽  
Common Rail ◽  
Injection System ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Spray Tip Penetration ◽  
Blended Fuel

The aim of this study was to investigate the spray characteristics of biodiesel and n-butanol/biodiesel blended fuel. The spray tip penetration and the spray cone angle were tested and analyzed. A constant volume chamber and high-speed camera were used to observe the spray evolution and a common-rail system was employed to change the injection pressure. The results show that the spray tip penetration and the spray cone angle of biodiesel are larger than those of blended fuel in most cases. n-Butanol additive changes the relationship between angle and density ratio to a certain degree. The experimental trend lines support the penetration model proposed by Hiroyasu and Arai in terms of similar proportional relation on time after start of injection, and the empirical equations provide reasonable agreement with the experimental data of the spray tip penetration.

Sign in / Sign up

Export Citation Format

Share Document