Theoretical and experimental studies of a piezoelectric ring energy harvester

2019 ◽  
Vol 30 (7) ◽  
pp. 998-1009 ◽  
Author(s):  
XF Zhang ◽  
HS Tzou
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Output Voltage ◽  
Laboratory Experiments ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Experimental Studies ◽  
Design Parameters ◽  
Resistive Load ◽  
Practical Applications

Based on the electromechanical coupling of piezoelectricity, a piezoelectric ring energy harvester is designed and tested in this study, such that the harvester can be used to power electric devices in the closed-circuit condition. Output energies across the external resistive load are evaluated when the ring energy harvester is subjected to harmonic excitations, and various design parameters are discussed to maximize the power output. In order to validate the theoretical energy harvesting results, laboratory experiments are conducted. Comparing experiment results with theoretical ones, the errors between them are under 10% for the output voltage. Laboratory experiments demonstrate that the ring energy harvester is workable in practical applications.

Finite Element Modeling and Experimental Studies of Stack-Type Piezoelectric Energy Harvester

2017 ◽  
Vol 09 (06) ◽  
pp. 1750084 ◽  
Author(s):  
L. V. Duong ◽  
M. T. Pham ◽  
V. A. Chebanenko ◽  
A. N. Solovyev ◽  
Chuong V. Nguyen
Keyword(s):  
Finite Element ◽  
Output Voltage ◽  
Energy Harvester ◽  
Numerical Models ◽  
Experimental Studies ◽  
Fe Model ◽  
Resistive Load ◽  
Piezoelectric Energy ◽  
Load Rate ◽  
1D Model

In this paper, closed-form coupled electromechanical one-dimensional (1D) model and finite element (FE) model for stack-type piezoelectric energy harvester (PEH) and delivery to a resistive load available in the literature were proposed. We obtained the values of some parameters of 1D model and set the boundaries of its applicability based on the comparison of the resonance frequency and output voltage between the FE model and 1D model. The numerical modeling results of the full-scale experiment with low-frequency pulse excitation of the stack-type PEH for the energy storage device are described. PEH is a multilayer axisymmetric piezoceramic package. The dependence between the output voltage and the current load rate under the harmonic and non-stationary mechanical action of the PEH is studied. The experimental results-to-numerical calculation correlation has shown their good coincidence, which allows using the analyzed numerical models to optimize the PEH design at the given external action frequency and the active resistance value of the external electric circuit. Besides, it found that the frequency dependence of the output voltage of the stack-type PEH is of a complex nature depending both on the compressive pulse loading level and the piezoelectric modulus value of the PEH sensitive element, and on the electrical load resistance.

Modeling of a Beam With a Mass in the Middle for Heart Beat Vibration Energy Harvesting

2014 ◽  
Author(s):  
Muath Bani-Hani ◽  
Venkat Krovi ◽  
M. Amin Karami
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Energy Harvester ◽  
Exact Analytical Solution ◽  
Heart Beat ◽  
Ambient Vibration ◽  
Vibration Source ◽  
Resistive Load ◽  
Vibration Energy Harvesting ◽  
Cardiac Devices

This work presents a model for energy harvesting characterization of a simply supported beam with a mass in the middle to be used for powering pacemakers from heartbeat vibrations. The required power for a typical pacemaker is about 1.0 microwatts. A uniform cross-section beam, bimorph structures, employing double piezoelectric layers is used. PSI-5H4E piezoelectric and brass substrate is used in this study. Different configurations are utilized to identify the optimal design for lightweight energy harvesting devices with low-power applications to tune the natural frequencies of the energy harvester towards the operating ambient vibration source. In this paper, the exact analytical solution of the piezoelectric beam energy harvester with Euler–Bernoulli beam assumptions is presented. The energy harvester is intended to generate power from heartbeat induced vibrations to power implantable cardiac devices. The base excitations are thus heartbeat induced tissue vibrations. The proposed configuration harvests energy from the reverberation of heartbeats and converts it to electricity and could generate about 0.22 microwatts of power. Using the Fourier transform, the frequency response function for the voltage; current and power of the harvester are obtained. The power output for a range of values for the resistive load connected to the bimorph PZT layers is investigated to determine the optimized value of the resistive load that gives the maximum power output for the corresponding configuration of the beam. Stress analysis is performed for the substrate and PZT layer to make sure that the stress are within the permissible values to avoid breaking or failing of the beam. Results show that the use of mid mass is capable of harvesting a significant power with the proposed configurations.

Flexoelectric Energy Harvesting of Circular Rings

2013 ◽  
Author(s):  
X. F. Zhang ◽  
S. D. Hu ◽  
H. S. Tzou
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Strain Gradient ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Design Parameters ◽  
Equivalent Resistance ◽  
Flexoelectric Effect ◽  
Piezoelectric Energy

Flexoelectricity, the electromechanical coupling of the polarization response and strain gradient, occurs in solid crystalline dielectrics of any symmetry or asymmetric crystals. Different from the piezoelectric energy harvester, an energy harvester based on the direct flexoelectric effect is designed in this study. The energy harvester consists of an elastic ring and a flexoelectric patch laminated on its outer surface. Due to the direct flexoelectric effect, the electric energy induced by the strain gradient of the flexoelectric patch is harvested to power the electric device when the ring is subjected to mechanical excitations. Electromechanical coupling equation of the flexoelectric energy harvesting system in close-loop circuit condition is derived. In this study, dynamic response, output power across the external resistor and energy harvesting results are evaluated when the ring is excited by a harmonic point loading. The output power is a function of the external excitation frequency, the external equivalent resistance, the flexoelectric patch’s thickness and other design parameters. Case studies of those parameters for the flexoelectric energy harvester are presented to optimize the output power. Results show that the optimal excitation frequency is equal to the natural frequency for each mode, and the optimal equivalent resistance is dependent of the equivalent capacitance of the flexoelectric patch and the excitation frequency. Since the output power of the flexoelectric energy harvester is similar to that of the piezoelectric energy harvester, comparison of the two harvesters is also discussed. With all the optimal conditions discussed, it can supply a design principle in the engineering applications.

Uncertainty Analysis of Energy Harvesting Systems

2014 ◽  
Author(s):  
Reza Madankan ◽  
M. Amin Karami ◽  
Puneet Singla
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Excitation Frequency ◽  
Excitation Amplitude ◽  
Design Parameters ◽  
Unscented Transformation ◽  
Energy Harvesters ◽  
Harvesting Systems

This paper presents the relation between uncertainty in the excitation and parameters of vibrational energy harvesting systems and their power output. Nonlinear vibrational energy harvesters are very sensitive to the frequency of the base excitation. If the excitation frequency does not match with the resonance frequency of the energy harvester, the power output significantly deteriorates. The mismatch can be due to the inherent changes of the ambient oscillations. The fabrication errors or gradual changes of material properties also result in the mismatch. This paper quantitatively shows the probability density function for the power as a function of the probability densities of the excitation frequency, excitation amplitude, initial deflection of the energy harvester, and design parameters. Recently developed the conjugated unscented transformation methodology is used in conjunction with the principle of maximum entropy to compute the probability distribution for the base response and power. The computed nonlinear density functions are validated against Monte Carlo simulations.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

Enhanced frequency synchronization for concurrent aeroelastic and base vibratory energy harvesting using a softening nonlinear galloping energy harvester

2021 ◽  
pp. 1045389X2110263
Author(s):  
Shun Chen ◽  
David Eager ◽  
Liya Zhao
Keyword(s):  
Energy Harvesting ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Poor Performance ◽  
Effective Bandwidth ◽  
Frequency Synchronization ◽  
Periodic Oscillations ◽  
Energy Harvesters ◽  
Paper Form ◽  
Excited Oscillation

This paper proposes a softening nonlinear aeroelastic galloping energy harvester for enhanced energy harvesting from concurrent wind flow and base vibration. Traditional linear aeroelastic energy harvesters have poor performance with quasi-periodic oscillations when the base vibration frequency deviates from the aeroelastic frequency. The softening nonlinearity in the proposed harvester alters the self-excited galloping frequency and simultaneously extends the large-amplitude base-excited oscillation to a wider frequency range, achieving frequency synchronization over a remarkably broadened bandwidth with periodic oscillations for efficient energy conversion from dual sources. A fully coupled aero-electro-mechanical model is built and validated with measurements on a devised prototype. At a wind speed of 5.5 m/s and base acceleration of 0.1 g, the proposed harvester improves the performance by widening the effective bandwidth by 300% compared to the linear counterpart without sacrificing the voltage level. The influences of nonlinearity configuration, excitation magnitude, and electromechanical coupling strength on the mechanical and electrical behavior are examined. The results of this paper form a baseline for future efficiency enhancement of energy harvesting from concurrent wind and base vibration utilizing monostable stiffness nonlinearities.

Optimization of energy harvesting based on the uniform deformation of piezoelectric ceramic

2016 ◽  
Vol 09 (05) ◽  
pp. 1650069 ◽  
Author(s):  
Yaoze Liu ◽  
Tongqing Yang ◽  
Fangming Shu
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Piezoelectric Ceramic ◽  
Energy Harvester ◽  
Optimization Method ◽  
Piezoelectric Energy ◽  
Bonding Area ◽  
Almost All ◽  
Matching Load ◽  
Tip Mass

Since the piezoelectric properties were used for energy harvesting, almost all forms of energy harvester needs to be bonded with a mass block to achieve pre-stress. In this article, disc type piezoelectric energy harvester is chosen as the research object and the relationship between mass bonding area and power output is studied. It is found that if the bonding area is changed as curved, which is usually complanate in previous studies, the deformation of the circular piezoelectric ceramic is more uniform and the power output is enhanced. In order to test the change of the deformation, we spray several homocentric annular electrodes on the surface of a piece of bare piezoelectric ceramic and the output of each electrode is tested. Through this optimization method, the power output is enhanced to more than 11[Formula: see text]mW for a matching load about 24[Formula: see text]k[Formula: see text] and a tip mass of 30[Formula: see text]g at its resonant frequency of 139[Formula: see text]Hz.

scholarly journals Modeling and Experiment of a V-Shaped Piezoelectric Energy Harvester

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Yue Zhao ◽  
Yi Qin ◽  
Lei Guo ◽  
Baoping Tang
Keyword(s):  
Energy Harvesting ◽  
Frequency Band ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Structural Parameters ◽  
Ambient Vibration ◽  
Piezoelectric Bimorph ◽  
Actual Structure ◽  
Piezoelectric Energy ◽  
Operation Frequency

Vibration-based energy harvesting technology is the most promising method to solve the problems of self-powered wireless sensor nodes, but most of the vibration-based energy harvesters have a rather narrow operation bandwidth and the operation frequency band is not convenient to adjust when the ambient frequency changes. Since the ambient vibration may be broadband and changeable, a novel V-shaped vibration energy harvester based on the conventional piezoelectric bimorph cantilevered structure is proposed, which successfully improves the energy harvesting efficiency and provides a way to adjust the operation frequency band of the energy harvester conveniently. The electromechanical coupling equations are established by using Euler-Bernoulli equation and piezoelectric equation, and then the coupled circuit equation is derived based on the series connected piezoelectric cantilevers and Kirchhoff's laws. With the above equations, the output performances of V-shaped structure under different structural parameters and load resistances are simulated and discussed. Finally, by changing the angle θ between two piezoelectric bimorph beams and the load resistance, various comprehensive experiments are carried out to test the performance of this V-shaped energy harvester under the same excitation. The experimental results show that the V-shaped energy harvester can not only improve the frequency response characteristic and the output performance of the electrical energy, but also conveniently tune the operation bandwidth; thus it has great application potential in actual structure health monitoring under variable working condition.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

scholarly journals FINITE ELEMENT SIMULATION OF MEMS PIEZOELECTRIC ENERGY SCAVENGER BASED ON PZT THIN FILM

2019 ◽  
Vol 20 (1) ◽  
pp. 90-99
Author(s):  
Aliza Aini Md Ralib ◽  
Nur Wafa Asyiqin Zulfakher ◽  
Rosminazuin Ab Rahim ◽  
Nor Farahidah Za'bah ◽  
Noor Hazrin Hany Mohamad Hanif
Keyword(s):  
Thin Film ◽  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
The World

Vibration energy harvesting has been progressively developed in the advancement of technology and widely used by a lot of researchers around the world. There is a very high demand for energy scavenging around the world due to it being cheaper in price, possibly miniaturized within a system, long lasting, and environmentally friendly. The conventional battery is hazardous to the environment and has a shorter operating lifespan. Therefore, ambient vibration energy serves as an alternative that can replace the battery because it can be integrated and compatible to micro-electromechanical systems. This paper presents the design and analysis of a MEMS piezoelectric energy harvester, which is a vibration energy harvesting type. The energy harvester was formed using Lead Zicronate Titanate (PZT-5A) as the piezoelectric thin film, silicon as the substrate layer and structural steel as the electrode layer. The resonance frequency will provide the maximum output power, maximum output voltage and maximum displacement of vibration. The operating mode also plays an important role to generate larger output voltage with less displacement of cantilever. Some designs also have been studied by varying height and length of piezoelectric materials. Hence, this project will demonstrate the simulation of a MEMS piezoelectric device for a low power electronic performance. Simulation results show PZT-5A piezoelectric energy with a length of 31 mm and height of 0.16 mm generates maximum output voltage of 7.435 V and maximum output power of 2.30 mW at the resonance frequency of 40 Hz. ABSTRAK: Penuaian tenaga getaran telah berkembang secara pesat dalam kemajuan teknologi dan telah digunakan secara meluas oleh ramai penyelidik di seluruh dunia. Terdapat permintaan yang sangat tinggi di seluruh dunia terhadap penuaian tenaga kerana harganya yang lebih murah, bersaiz kecil dalam satu sistem, tahan lama dan mesra alam. Manakala, bateri konvensional adalah berbahaya bagi alam sekitar dan mempunyai jangka hayat yang lebih pendek. Oleh itu, getaran tenaga dari persekitaran lebih sesuai sebagai alternatif kepada bateri kerana ia mudah diintegrasikan dan serasi dengan sistem mikroelektromekanikal. Kertas kerja ini  membentangkan reka bentuk dan analisis tenaga piezoelektrik MEMS iaitu salah satu jenis penuaian tenaga getaran. Penuai tenaga ini dibentuk menggunakan Lead Zicronate Titanate (PZT-5A) sebagai lapisan filem tipis piezoelektrik, silikon sebagai lapisan substrat dan keluli struktur sebagai lapisan elektrod. Frekuensi resonans akan memberikan hasil tenaga maksima, voltan tenaga maksima dan getaran jarak maksima. Mod pengendalian juga memainkan peranan penting bagi menghasilkan tenaga yang lebih besar. Reka bentuk yang mempunyai ketinggian dan panjang berlainan juga telah diuji dengan menggunakan bahan piezoelektrik yang sama. Oleh itu, projek ini akan menghasilkan simulasi piezoelektrik MEMS yang sesuai digunakan bagi alat elektronik berkuasa rendah. Hasil simulasi menunjukkan dengan panjang 31 mm dan ketinggian 0.16 mm, piezoelektrik PZT ini menghasilkan voltan maksima sebanyak 7.435 V dan tenaga output maksima 2.30 mW pada frekuensi resonans 40 Hz.

Sign in / Sign up

Export Citation Format

Share Document