scholarly journals Elasto-plastic analysis of the contact region between a rigid ellipsoid and a semi-flat surface

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401879739 ◽  
Author(s):  
Pengyang Li ◽  
Lingxia Zhou ◽  
Fangyuan Cui ◽  
Quandai Wang ◽  
Meiling Guo ◽  
...  
Keyword(s):  
Residual Stress ◽  
Plastic Deformation ◽  
Plastic Strain ◽  
Contact Pressure ◽  
Contact Region ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Effective Plastic Strain ◽  
Normal Forces ◽  
Von Mises

When the load acting on a mechanical structure is greater than the yield strength of the material, the contact surface will undergo plastic deformation. Cumulative plastic deformation has an important influence on the lifespan of mechanical parts. This article presents a three-dimensional semi-analytical model based on the conjugate gradient method and fast Fourier transform algorithm, with the aim of studying the characteristic parameters of the contact region between a rigid ellipsoid and elasto-plastic half-space. Moreover, normal forces and tangential traction were considered, as well as the contact pressure resulting from various sliding speeds and friction coefficients. The contact pressure, effective plastic strain, von Mises stress, and residual stress were measured and shown to increase with increasing sliding velocity. Finally, when the friction coefficient, contact pressure, and effective plastic strain are increased, the von Mises stress is also shown to increase, whereas the residual stress decreases.

Plasto-Elastohydrodynamic Lubrication in Point Contacts for Surfaces With Three-Dimensional Sinusoidal Waviness and Real Machined Roughness

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Tao He ◽  
Ning Ren ◽  
Dong Zhu ◽  
Jiaxu Wang
Keyword(s):  
Plastic Deformation ◽  
Rough Surface ◽  
Mechanical Design ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Von Mises Stress ◽  
Asperity Contacts ◽  
Lubrication Characteristics ◽  
Von Mises

Efficiency and durability are among the top concerns in mechanical design to minimize environmental impact and conserve natural resources while fulfilling performance requirements. Today mechanical systems are more compact, lightweight, and transmit more power than ever before, which imposes great challenges to designers. Under the circumstances, some simplified analyses may no longer be satisfactory, and in-depth studies on mixed lubrication characteristics, taking into account the effects of 3D surface roughness and possible plastic deformation, are certainly needed. In this paper, the recently developed plasto-elastohydrodynamic lubrication (PEHL) model is employed, and numerous cases with both sinusoidal waviness and real machined roughness are analyzed. It is observed that plastic deformation may occur due to localized high pressure peaks caused by the rough surface asperity contacts, even though the external load is still considerably below the critical load determined at the onset of plastic deformation in the corresponding smooth surface contact. It is also found, based on a series of cases analyzed, that the roughness height, wavelength, material hardening property, and operating conditions may all have significant influences on the PEHL performance, subsurface von Mises stress field, residual stresses, and plastic strains. Generally, the presence of plastic deformation may significantly reduce some of the pressure spikes and peak values of subsurface stresses and make the load support more evenly distributed among all the rough surface asperities in contact.

scholarly journals A Finite Element Study of the Residual Stress and Deformation in Hemispherical Contacts

2005 ◽  
Vol 127 (3) ◽  
pp. 484-493 ◽  
Author(s):  
Robert Jackson ◽  
Itti Chusoipin ◽  
Itzhak Green
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Yield Criterion ◽  
Contact Region ◽  
Element Model ◽  
Von Mises Stress ◽  
Contact Radius ◽  
Perfectly Plastic ◽  
Von Mises

This work presents a finite element model (FEM) of the residual stresses and strains that are formed after an elastoplastic hemispherical contact is unloaded. The material is modeled as elastic perfectly plastic and follows the von Mises yield criterion. The FEM produces contours for the normalized axial and radial displacements as functions of the removed interference depth and location on the surface of the hemisphere. Contour plots of the von Mises stress and other stress components are also presented to show the formation of the residual stress distribution with increasing plastic deformation. This work shows that high residual von Mises stresses appear in the material pileup near the edge of the contact area after complete unloading. Values are defined for the minimum normalized interference, that when removed, results in plastic residual stresses. This work also defines an interference at which the maximum residual stress transitions from a location below the contact region and along the axis of symmetry to one near to the surface at the edge of the contact radius (within the pileup).

A Study on Bird Impact Damages on Shrouded Fan Blades of an Aero-Engine

2013 ◽  
Author(s):  
Raghu Prakash ◽  
Hithesh Channegowda ◽  
Anandavel Kaliyaperumal
Keyword(s):  
Plastic Strain ◽  
Impact Resistance ◽  
Three Dimensional ◽  
Impact Response ◽  
Von Mises Stress ◽  
Aero Engine ◽  
Bird Impact ◽  
Critical Components ◽  
Von Mises ◽  
The Impact

Aero-engine fan blades are the critical components that are vulnerable to Foreign Object Damage (FOD) such as bird impact. The thrust loss due to bird impact can affect engine core function, resulting in catastrophic failure. The fan blades should be designed to have adequate resistance to bird impact. The present paper focuses on numerical evaluation of bird impact response on shrouded and un-shrouded rotating set of fan blades using three dimensional computational methodology. The impact response is compared between shrouded and un-shrouded blades in terms of deformation, von-Mises stress, plastic strain, and energy absorbed. Numerical analysis results indicate that the shrouded fan blade absorbs 35 % more energy compared to un-shrouded blade. Deformation damage at impact location of shrouded blade is lesser compared to un-shrouded blade. The maximum plastic strain observed on shrouded blade due to bird impact is also 50 % lesser than the un-shrouded blade. The study suggests that the shrouded fan blades provide better impact resistance characteristics to bird impact compared to un-shrouded fan blades.

Numerical Simulation for Rough Contact Incorporating Plastic Deformation

2005 ◽  
Author(s):  
Fan Wang ◽  
Leon M. Keer
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Plastic Deformation ◽  
Plastic Strain ◽  
Pressure Distribution ◽  
Contact Pressure ◽  
Analytical Method ◽  
Elastic Contact ◽  
Surface Deflection ◽  
Plastic Hardening

An 3D elastic-plastic rough contact solution and code is developed using a modified semi-analytical method. It is supposed that the total surface deflection is induced by the contact pressure and plastic strain. The purely elastic contact and the influence of the plastic deformation are calculated iteratively until convergence is satisfied. The distributions of contact pressure, residual stress and plastic strain are obtained through simulation. The effects of roughness and plastic hardening upon the pressure distribution are discussed.

DYNAMIC CONTACT ANALYSIS OF TOTAL HIP PROSTHESIS DURING STUMBLING CYCLE

2014 ◽  
Vol 14 (03) ◽  
pp. 1450041 ◽  
Author(s):  
S. SHANKAR ◽  
M. MANIKANDAN
Keyword(s):  
Contact Pressure ◽  
Hip Prosthesis ◽  
Three Dimensional ◽  
Load Condition ◽  
Dynamic Contact ◽  
Element Model ◽  
Von Mises Stress ◽  
Metal Metal ◽  
Joint Contact ◽  
Von Mises

The estimation of the hip joint contact stresses and contact pressure distribution during stumbling activities is a critical task for selecting the best material pair in the hip prosthesis design. This paper utilizes a three-dimensional finite element model of acetabular component to analyze the dynamic stumbling activity using ANSYS®. The present study investigates the maximum von Mises stress, contact pressure and deformation developed for different combinations of materials under the stumbling load condition. The different combination of bearing couplings considered for the analysis are metal in contact with plastic, metal on metal, metal on ceramic, ceramic on plastic, ceramic on metal and ceramic on ceramic combinations. The results concluded that the Alumina femoral head paired with ultra-high molecular weight polyethylene (UHMWPE) cup reduces the maximum von Mises stress and maximum contact pressure developed between the interface regions when compared with other combinations. The obtained results are compared with the result of Hai-bo-Jiang et al., for available combinations, and higher correlation of 92% was found between the two results.

FE simulation of sealing ability for premium connection based on ISO 13679 CAL IV tests

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yihua Dou ◽  
Yufei Li ◽  
Yinping Cao ◽  
Yang Yu ◽  
Jiantao Zhang ◽  
...  
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Thermal Cycle ◽  
Three Dimensional ◽  
Element Model ◽  
Helix Angle ◽  
Von Mises Stress ◽  
Content Type ◽  
Von Mises ◽  
Three Dimensional Finite Element

PurposeTo maintain the well integrity, the strength and sealing ability of premium connection should be in the safe scope. ISO 13679 is widely used for evaluating the ability of tubing and casing connection all over the world. FE is adopted to simulate the ISO 13679 tests.Design/methodology/approachBecause of the disadvantage of experiment such as long period, high cost and high requirement on the facility, considering the convenience and universality of finite element method, as well as the contacting nonlinearity and material nonlinearity, three-dimensional finite element model of a certain type of premium connection is established with the consideration of helix angle. The loads exerted on the premium connection are the loads in series B test and thermal cycle test of ISO 13679. The distributions of Von Mises stress and contact pressure in various cases were studied.FindingsThe results showed that the bending load has a great influence on the distribution of Von Mises stress and contact pressure for premium connection. The Von Mises stress and contact pressures on the sealing surface are smaller on the tension side and greater on the compression side. With increasing axial compression load, the contact pressures on the tension side are too small, which may lead to sealing failure. The influence of temperature on the performance of premium connection cannot be ignored when choosing or designing premium connections. Both the Von Mises stress and contact pressure decrease slightly during a period of thermal cycle. Although the performance of the premium connection is good in a period of thermal cycle, its performance in a long period should be evaluated. Finite element simulation can effectively simulate the ISO 13679 test procedure and obtain the stress and contact pressure distribution. It can be used as a reference for evaluating the performance of premium connections.Originality/valueConsidering the convenience and universality of finite element method, as well as the contacting nonlinearity and material nonlinearity, three-dimensional finite element model of a certain type of premium connection is established with the consideration of helix angle.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

scholarly journals Effects of intracorneal ring segments implementation technique and design on corneal biomechanics and keratometry in a personalized computational analysis

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Niksa Mohammadi Bagheri ◽  
Mahmoud Kadkhodaei ◽  
Shiva Pirhadi ◽  
Peiman Mosaddegh
Keyword(s):  
Clinical Data ◽  
Three Dimensional ◽  
Element Model ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Average Error ◽  
Constant Thickness ◽  
Arc Length ◽  
Implementation Techniques ◽  
Von Mises

AbstractThe implementation of intracorneal ring segments (ICRS) is one of the successfully applied refractive operations for the treatment of keratoconus (kc) progression. The different selection of ICRS types along with the surgical implementation techniques can significantly affect surgical outcomes. Thus, this study aimed to investigate the influence of ICRS implementation techniques and design on the postoperative biomechanical state and keratometry results. The clinical data of three patients with different stages and patterns of keratoconus were assessed to develop a three-dimensional (3D) patient-specific finite-element model (FEM) of the keratoconic cornea. For each patient, the exact surgery procedure definitions were interpreted in the step-by-step FEM. Then, seven surgical scenarios, including different ICRS designs (complete and incomplete segment), with two surgical implementation methods (tunnel incision and lamellar pocket cut), were simulated. The pre- and postoperative predicted results of FEM were validated with the corresponding clinical data. For the pre- and postoperative results, the average error of 0.4% and 3.7% for the mean keratometry value ($$\text {K}_{\text{mean}}$$ K mean ) were predicted. Furthermore, the difference in induced flattening effects was negligible for three ICRS types (KeraRing segment with arc-length of 355, 320, and two separate 160) of equal thickness. In contrast, the single and double progressive thickness of KeraRing 160 caused a significantly lower flattening effect compared to the same type with constant thickness. The observations indicated that the greater the segment thickness and arc-length, the lower the induced mean keratometry values. While the application of the tunnel incision method resulted in a lower $$\text {K}_{\text{mean}}$$ K mean value for moderate and advanced KC, the induced maximum Von Mises stress on the postoperative cornea exceeded the induced maximum stress on the cornea more than two to five times compared to the pocket incision and the preoperative state of the cornea. In particular, an asymmetric regional Von Mises stress on the corneal surface was generated with a progressive ICRS thickness. These findings could be an early biomechanical sign for a later corneal instability and ICRS migration. The developed methodology provided a platform to personalize ICRS refractive surgery with regard to the patient’s keratoconus stage in order to facilitate the efficiency and biomechanical stability of the surgery.

Effect of Residual Stress or Plastic Deformation History on Fatigue Life Simulation of Pipeline Dents

2018 ◽  
Author(s):  
Xian-Kui Zhu ◽  
Rick Wang
Keyword(s):  
Residual Stress ◽  
Plastic Deformation ◽  
Fatigue Life ◽  
Residual Stresses ◽  
Three Dimensional ◽  
Strain History ◽  
Deformation History ◽  
Stress Strain ◽  
Element Analysis ◽  
Fea Model

Mechanical dents often occur in transmission pipelines, and are recognized as one of major threats to pipeline integrity because of the potential fatigue failure due to cyclic pressures. With matured in-line-inspection (ILI) technology, mechanical dents can be identified from the ILI runs. Based on ILI measured dent profiles, finite element analysis (FEA) is commonly used to simulate stresses and strains in a dent, and to predict fatigue life of the dented pipeline. However, the dent profile defined by ILI data is a purely geometric shape without residual stresses nor plastic deformation history, and is different from its actual dent that contains residual stresses/strains due to dent creation and re-rounding. As a result, the FEA results of an ILI dent may not represent those of the actual dent, and may lead to inaccurate or incorrect results. To investigate the effect of residual stress or plastic deformation history on mechanics responses and fatigue life of an actual dent, three dent models are considered in this paper: (a) a true dent with residual stresses and dent formation history, (b) a purely geometric dent having the true dent profile with all stress/strain history removed from it, and (c) a purely geometric dent having an ILI defined dent profile with all stress/strain history removed from it. Using a three-dimensional FEA model, those three dents are simulated in the elastic-plastic conditions. The FEA results showed that the two geometric dents determine significantly different stresses and strains in comparison to those in the true dent, and overpredict the fatigue life or burst pressure of the true dent. On this basis, suggestions are made on how to use the ILI data to predict the dent fatigue life.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

Sign in / Sign up

Export Citation Format

Share Document