scholarly journals The effect of welded joint properties on the surface characteristics of laser-welded 2205 duplex stainless steel

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401879744 ◽  
Author(s):  
Shanshan Hu ◽  
Dongrui Zheng ◽  
Guolin Zhao ◽  
Guangliang Li ◽  
Hongqun Tang
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Surface Quality ◽  
Welded Joints ◽  
Welded Joint ◽  
Surface Characteristics ◽  
Welding Parameters ◽  
Joint Properties ◽  
Welding Surface

Welded joints of poor welding surface quality are sensitive to stress concentrations, affecting both the tensile strength of workpieces and the fluidity of liquids and gases in pressure and liquid containers. Orthogonal experiments involving the laser welding of 1-mm-thick duplex stainless steel sheets were conducted using different electric current, pulse width and frequency values in order to analyse the effect of welding properties on the surface characteristics of the welded joints. Rapid judgement regarding the welded joint properties was made based on the observed welding surface quality. The results show that an even phase proportion and grain refinement are not necessarily guaranteed to provide good welding surface quality. A satisfactory welding surface quality characterised by a smaller spot pitch or spot pitch difference, smaller weld width, reduced surface roughness and valley depth of surface waviness implies better welded joint mechanical characteristics and a more even microstructure. The specimen with the most suitable welding parameters and the greatest heat input can reach the lowest volume fraction of ferrite phase of 42.5% and the highest tensile strength of 848 MPa, and its surface quality is the best.

scholarly journals Influence of Parameters of Laser Beam Welding on Structure of 2205 Duplex Stainless Steel

2019 ◽  
Vol 19 (1) ◽  
pp. 21-31 ◽  
Author(s):  
M. Landowski
Keyword(s):  
Stainless Steel ◽  
Laser Beam ◽  
Laser Welding ◽  
Duplex Stainless Steel ◽  
Welded Joints ◽  
Laser Beam Welding ◽  
Welding Parameters ◽  
Processing Technologies ◽  
High Level ◽  
The Impact

AbstractLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical multidimensional processes complexity requires a deeper understanding of the impact of laser welding parameters on the quality of welded joints for industrial implementation. The paper presents results of microstructure investigations of laser beam welded stainless steel under various welding parameters. Welded joints was achieved by Ytterbium fiber laser type without the use of the filler material. Material for test was 2205 ferritic-austenitic duplex stainless steel (DSS) plates with thickness of 8 mm in delivery condition. The objectives of this research was to investigate influence of laser welding parameters on weld geometry of butt-welded joints. Investigations of bead shape revealed correlation between laser beam focus position and weld penetration depth.

scholarly journals Mechanical Properties and Microstructural Characterization of Laser Welded S32520 Duplex Stainless Steel

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5532
Author(s):  
Hany S. Abdo ◽  
Asiful H. Seikh
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Process Parameters ◽  
Welded Joint ◽  
Weld Zone ◽  
Heat Energy ◽  
Beam Diameter ◽  
Butt Weld ◽  
The Impact

This paper investigates an experimental design of laser butt welding of S32520 duplex stainless steel, which has been passed out with the help of a pulsed Nd: YAG laser supply. The intention of the present research is to learn the impact of beam diameter, welding speed, and laser power on the superiority of the butt weld. The individuality of butt joints has been characterized in terms of tensile properties, fractography, and hardness. It was noticed that unbalanced particle orientations indirectly produce a comparatively fragile quality in the laser welded joint. The outcome of varying process parameters and interaction effect of process parameters on ultimate tensile strength and micro hardness were studied through analysis of experimental data. With different process parameters, the heat energy delivered to the material was changed, which was reflected in tensile strength measurement for different welded samples. From this present research, it was shown that, up to a certain level, an increase in process parameters amplified the tensile strength, but after that, certain level tensile strength decreased with the increase in process parameters. When process parameters exceeded that certain level, the required amount of heat energy was not delivered to the material, resulting in low bead width and less penetration, thus producing less strength in the welded joint. Less strength leads to more ductile weld joints. Microhardness was higher in the weld zone than in the base region of welded samples. However, the heat affected zone had a high microhardness range.

scholarly journals Improving the Properties of Laser-Welded Al–Zn–Mg–Cu Alloy Joints by Aging and Double-Sided Ultrasonic Impact Compound Treatment

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2742
Author(s):  
Furong Chen ◽  
Chenghao Liu
Keyword(s):  
Plastic Deformation ◽  
Tensile Strength ◽  
Tensile Properties ◽  
Welded Joints ◽  
Welded Joint ◽  
Weld Zone ◽  
Aging Treatment ◽  
Residual Tensile Stress ◽  
Impact Surface ◽  
Deformation Layer

To improve the loose structure and serious porosity of (Al–Zn–Mg–Cu) 7075 aluminum alloy laser-welded joints, aging treatment, double-sided ultrasonic impact treatment (DSUIT), and a combination of aging and DSUIT (A–DSUIT) were used to treat joints. In this experiment, the mechanism of A–DSUIT on the microstructure and properties of welded joints was analyzed. The microstructure of the welded joints was observed using optical microscopy, scanning electron microscopy, and electron backscatter diffraction (EBSD). The hardness and tensile properties of the welded components under the different processes were examined via Vickers hardness test and a universal tensile testing machine. The results showed that, after the aging treatment, the dendritic structure of the welded joints transformed into an equiaxed crystal structure. Moreover, the residual tensile stress generated in the welding process was weakened, and the hardness and tensile strength were significantly improved. After DSUIT, a plastic deformation layer of a certain thickness was generated from the surface downward, and the residual compressive stress was introduced to a certain depth of the joint. However, the weld zone unaffected by DSUIT still exhibited residual tensile stress. The inner microhardness of the joint surface improved; the impact surface hardness was the largest and gradually decreased inward to the weld zone base metal hardness, with a small improvement in the tensile strength. Compared with the single treatment process, the microstructural and mechanical properties of the welded joint after A–DSUIT were comprehensively improved. The microhardness and tensile strength of the welded joint reached 200 HV and 615 MPa, respectively, for an increase of 45.8% and 61.8%, respectively. Observation of the fractures of the tensile specimens under the different treatment processes showed that the fractures before the aging treatment were mainly ductile fractures while those after were mainly brittle fractures. After DSUIT of the welded joints, a clear and dense plastic deformation layer was observed in the fracture of the tensile specimens and effectively improved the tensile properties of the welded joints. Under the EBSD characterization, the larger the residual compressive stress near the ultrasonic impact surface, the smaller the grain diameter and misorientation angle, and the lower the texture strength. Finally, after A–DSUIT, the hardness and tensile properties improved the most.

Optimization of friction stir welding parameters of dissimilar aluminium alloys 6061 and 5083 by using response surface methodology

2021 ◽  
pp. 095440622110058
Author(s):  
Sanjeev Verma ◽  
Vinod Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Tilt Angle ◽  
Feed Rate ◽  
Aluminium Alloys ◽  
Welded Joint ◽  
Welding Parameters ◽  
Friction Stir ◽  
Industrial Sectors ◽  
Tool Pin

Aluminium and its alloys are lightweight, corrosion-resistant, affordable and high-strength material and find wide applications in shipbuilding, automotive, constructions, aerospace and other industrial sectors. In applications like aerospace, marine and automotive industries, there is a need to join components made of different aluminium alloys, viz. AA6061 and AA5083. In this study friction stir welding (FSW) is used to join dissimilar plates made of AA6061-T6 and AA5083-O. The effect of varying tool pin profile, tool rotation speed, tool feed rate and tilt angle of the tool has been investigated on the tensile strength and percentage elongation of the welded joints. Box-Behkan design, with four input parameters and three levels of each parameter has been employed to decide the set of experimental runs. The regression models have been developed to investigate the influence of welding variables on the tensile strength and elongation of the welded joint. It is revealed that with the increase in welding parameters like tool rpm, tool feed rate and tilt angle of the tool, both the mechanical properties increase, reach a maximum level, followed by a decrease with further increase in the value of parameters. Amongst different types of tool pin profiles used, the FSW tool having straight cylindrical (SC) pin profile is found to yield the maximum strength and elongation of the welded joint for different combinations of welding parameters. Multiple response optimization indicates that the maximum UTS (135.83 MPa) and TE (4.35%) are obtained for the welded joint fabricated using FSW tool having SC pin profile, tilted at 1.11° and operating at tool speed and feed rate of 1568 rpm and 39.53 mm/min., respectively.

Electric Current Pulse Welding of Titanium with 18-10 Stainless Steel

2009 ◽  
Vol 83-86 ◽  
pp. 1251-1253 ◽  
Author(s):  
E.G. Grigoryev ◽  
V.N. Bazanov
Keyword(s):  
Stainless Steel ◽  
Electric Current ◽  
Current Pulse ◽  
Contact Zone ◽  
Welded Joints ◽  
High Speed ◽  
Welded Joint ◽  
Electric Current Pulse ◽  
Pulse Effect ◽  
Different Thickness

The purpose of the work was to determine the capabilities of the pulse effect of electric current and pressure to produce welded joints of various component parts of different thickness from 18-10 stainless steel and titanium. Application of electric current pulses on the surfaces of contacting metallic conductors leads to considerable changes in the surface structure. Depending on the initial state of the surfaces and parameters of the pulse effect this can result in melting without formation of joints, formation of a strong welded joint with characteristics no worse than those of welded metals, and in destruction of the contact zone. A combination of a short electric pulse with simultaneous application of mechanical pressure in the weld zone causes high-speed deformation of the contact zone. The process of joint formation itself does not cause any appreciable diffusion during welding. The greatest energy emission and the maximal heating occur on the contacting surfaces being welded with the passage of an electric current pulse through the welding zone. Simultaneously with intensive heating, and due to applied pressure, high-speed deformation of materials takes place and a strong welded joint is formed. Optimal parameters for the welding of titanium and 18-10 stainless steel have been determined on the basis of the tests conducted. Investigations into the welding of titanium and 18-10 stainless steel have shown that application of a short electric current pulse and pressure produces stronger welded joints composed of both similar and different metals of considerably different thickness.

Influence of Rotary Friction Welding Parameters on Tensile Strength and Length of TMAZ of Dissimilar Welded Joints from 32G2 and 40KhN Steels

2021 ◽  
Vol 410 ◽  
pp. 299-305
Author(s):  
Artem S. Atamashkin ◽  
Elena Y. Priymak ◽  
Elena A. Kuzmina
Keyword(s):  
Tensile Strength ◽  
Base Metal ◽  
Process Parameters ◽  
Welded Joints ◽  
Friction Welding ◽  
Tensile Tests ◽  
Welding Parameters ◽  
Rotary Friction Welding ◽  
Study Results ◽  
Friction Pressure

In this work, pipe billets with a diameter of 73 mm and a wall thickness of 9 mm from steels 32G2 and 40KhN are friction welded with an aim to optimize the process parameters. The friction pressure, the forging pressure and the length of the fusion varied. After the implementation of various welding modes, tensile tests and metallographic studies were carried out. The optimal welding parameters have been established, which make it possible to obtain tensile strength at the level of the 32G2 base metal. The study results of the microstructure and SEM fractographs after the optimal welding mode are presented.

Sign in / Sign up

Export Citation Format

Share Document