Influence of single and double aging treatment on microstructures and mechanical properties of cold rolled Ti–30Nb–5Ta–6Zr alloy

2013 ◽  
Vol 30 (2) ◽  
pp. 189-195 ◽  
Author(s):  
Y. Wang ◽  
S. Dai ◽  
F. Chen ◽  
X. Yu ◽  
Y. Zhang
Keyword(s):  
Mechanical Properties ◽  
Aging Treatment ◽  
Double Aging ◽  
Cold Rolled ◽  
Microstructures And Mechanical Properties

Researches on Microstructures and Mechanical Properties of Extruded Mg-Zn-Zr-Y Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 715-717
Author(s):  
Jian Peng ◽  
Rong Shen Liu ◽  
Ding Fei Zhang ◽  
Cheng Meng Song
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Aging Treatment ◽  
High Strength ◽  
Treatment Processes ◽  
Medium Strength ◽  
Microstructures And Mechanical Properties ◽  
Extruded Products

The microstructures and mechanical properties of Mg-Zn-Zr-Y alloy extruded bar with different heat treatment processes were investigated, including solution treatments of 400 oC, 450 oC and 500 oC for 3 hours followed by 170 oC×24h aging treatment, and solely aging treatments of 160 oC, 180 oC for 24hours without solution after extruding. By comparing the grain size, strength and elongation of the samples, the heat treatment processes for extruded products with high strength and with medium strength were recommended.

Effect of Zr on the microstructures and mechanical properties of as-extruded Mg–2.3Zn–0.18Y–xZr alloys

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744001 ◽  
Author(s):  
Yufan Wang ◽  
Yingbo Zhang ◽  
Wei Gao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Aging Treatment ◽  
Grain Refining ◽  
Maximum Increase ◽  
Microstructures And Mechanical Properties ◽  
Average Size ◽  
Precipitate Strengthening ◽  
Zr Alloys

The microstructures and mechanical properties of as-extruded Mg–2.3Zn–0.18Y–[Formula: see text]Zr ([Formula: see text] = 0.03, 0.06 and 0.13 at.%) alloys and aged Mg–2.3Zn–0.18Y–0.13Zr alloy were studied. The results revealed that the microstructures of as-extruded Mg–2.3Zn–0.18Y–[Formula: see text]Zr alloys are typical bimodal structures. The coarse [Formula: see text]-Mg grains are surrounded by fine dynamically recrystallized [Formula: see text]-Mg grains. The average size of [Formula: see text]-Mg grains decreases with increasing Zr content. Moreover, the addition of Zr (at.%) can improve the mechanical properties of alloy. The as-extruded Mg–2.3Zn–0.18Y–0.13Zr alloy has the best mechanical properties with ultimate tensile strength (UTS) and yield strength (YS) of 346 MPa and 292 MPa, respectively, and an elongation of 26.7%, which can be attributed to the grain refining effect and precipitate strengthening. The UTS and elongation of Mg–2.3Zn–0.18Y–0.13Zr alloy changed slightly after aging treatment, but the YS increases remarkably, with the maximum increase of 30 MPa. The fracture surfaces of all alloys consist of many tearing ridges and dimples.

Aging Treatment on the Microstructures and Mechanical Properties of New Groove T92/Super 304H Dissimilar Steel Joints

2015 ◽  
Vol 34 (5) ◽  
Author(s):  
Jianguo Deng ◽  
Zhiyuan Liang ◽  
Shi’en Hui ◽  
Qinxin Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Heat Affected Zone ◽  
Weld Seam ◽  
Aging Treatment ◽  
Coarse Grained ◽  
Dissimilar Steel ◽  
Weld Joints ◽  
Microstructures And Mechanical Properties ◽  
Steel Joints

AbstractThe effect of aging treatment on the microstructures and mechanical properties of new groove T92/Super 304H dissimilar steel joints is studied in this paper. The experimental results show that the heat-affected zone (HAZ) of T92 is mainly composed of coarse-grained and fine-grained martensitic, whereas the microstructure of Super 304H HAZ and weld seam exhibit an austenitic structure. Aging treatment increases the nucleation and growth of second phase particles of the weld joints, especially at T92 side. The weld joints have a low tensile strength (<700 Mpa) and a high tensile strength (>700 Mpa) when the tensile fractures are located at weld seam and T92 base metal, respectively. With increasing aging time, the hardness and tensile strength of the weld joints initially decrease, then increase, and finally stabilize. Moreover, the weld joints have a maximum hardness value at the T92 heat-affected zone. At room temperature condition, the impact absorbed energy reaches the minimum value, which is related to the coarse grain containing equiaxed dendrites in the weld seam.

Sign in / Sign up

Export Citation Format

Share Document