scholarly journals Control Performance Evaluation of Serial Urology Manipulator by Virtual Prototyping

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Hu Shi ◽  
Jiajie Li ◽  
Lianjie Guo ◽  
Xuesong Mei
Keyword(s):  
Fixed Point ◽  
Feedback Control ◽  
Feedforward Control ◽  
Tracking Error ◽  
Dynamics Simulation ◽  
Average Error ◽  
Bottom Surface ◽  
End Effector ◽  
Manipulator Design ◽  
Control Implementation

AbstractProstatic hyperplasia and tumor are common diseases, and the minimally invasive surgery inserting the instruments through the urethra into the prostate is commonly conducted. Taking the robotic manipulator for such surgery into consideration, this paper analyses the workspace of the end effector, and proposes the distribution error of the fixed point and the tracking error of manipulator end effector on the cone bottom surface of the workspace as the basis for control implementation of the manipulator. The D-H coordinate system of the manipulator is established and the trajectory planning of the end effector in the Cartesian space is carried out. The digital model was established, and dynamics simulation was performed in Solidworks and Matlab/Simulink environment to guide the manipulator design. Trajectory mapping and synchronization control between virtual model and the actual manipulator are realized based on digital twin technique. The virtual manipulator can reflect the real-time state of the manipulator with data interaction by comparing the dynamics simulation results with the motor current values obtained by experiment. Experiment was carried out with PD feedback control and Newton–Euler dynamics based feedforward control to get the trajectory tracking characteristic of each motor, errors of the fixed point and tracking performance of the end effector of the manipulator. The results show that compared with PD feedback control, feed forward control implementation can achieve a reduction of 30.0% in the average error of the fixed point of the manipulator and a reduction of 33.3% in the maximum error.

Task-Space Control Design and Performance Evaluation for a 6DOF Stewart Nanoscale Platform

2008 ◽  
Author(s):  
Chun-Chung Li ◽  
Yung Ting ◽  
Yi-Hung Liu ◽  
Yi-Da Lee ◽  
Chun-Wei Chiu
Keyword(s):  
Feedback Control ◽  
Hybrid Control ◽  
Feedforward Control ◽  
Feedback Controller ◽  
Test Method ◽  
Computation Method ◽  
Task Space ◽  
Force Output ◽  
End Effector ◽  
Control Scheme

A 6DOF Stewart platform using piezoelectric actuators for nanoscale positioning objective is designed. A measurement method that can directly measure the pose (position and orientation) of the end-effector is developed so that task-space on-line control is practicable. The design of a sensor holder for sensor employment, a cuboid with referenced measure points, and the computation method for obtaining the end-effector parameters is introduced. A control scheme combining feedforward and feedback is proposed. The inverse model of a hysteresis model derived by using a dynamic Preisach method is used for the feedforward control. Hybrid control to maintain both the positioning and force output for nano-cutting and nano-assembly applications is designed for the feedback controller. The optimal gain of the feedback controller is searched by using relay feedback test method and genetic algorithm. In experiment, conditions with/without external load employed with feedforward, feedback, and feedforward with feedback control schemes respectively are carried out. Performance of each control scheme verifies the capability of achieving nanoscale precision. The combined feedforward and feedback control scheme is superior to the others for gaining better precision.

A mixed approach for the control of a testing equipment employed for earthquake isolation systems

2013 ◽  
Vol 228 (2) ◽  
pp. 246-261 ◽  
Author(s):  
Stefano Pagano ◽  
Michele Russo ◽  
Salvatore Strano ◽  
Mario Terzo
Keyword(s):  
Feedback Control ◽  
Feedforward Control ◽  
Dead Zone ◽  
Reaction Force ◽  
Tracking Error ◽  
Experimental Tests ◽  
Test Rig ◽  
Actuation System ◽  
Non Linear ◽  
The Stability

This paper presents an activity concerning the modelling and control of a system adopted to perform shear tests on seismic isolators. The test rig consists of a hydraulic actuation system that drives a sliding table mounted on linear bearings. The system is characterized by non-linearities such as hydraulic proportional valve dead zone and frictions. A non-linear model is derived and then employed for parameter identification procedure. The test rig needs a suitable controller able to guarantee the desired table displacement in presence of unknown reaction force of the device under test. The proposed approach consists of a feedforward control integrated with a feedback one. The feedforward control law takes the form of a non-linear inverse model of the system. In this way, it is possible to obtain the desired target without affecting the stability of the test rig. The feedback control has the function to compensate for tracking error due to the model uncertainties and the unknown isolator reaction force. Therefore, the feedback control is not required to compensate for the large non-linearities: in this manner, it is possible to obtain good tracking results without the increasing of the feedback control gain that would change the stability properties of the plant. Numerical simulations have been performed in order to evaluate the goodness of the designed control with and without the specimen under test. Experimental tests show that the controlled system simulations are able to predict the controller performance. The experimental results also confirm that the performance of the proposed controller fully satisfy the standards concerning the testing procedure of seismic isolators.

Use of vent stack temperature as a feedforward variable for dissolver total titratable alkali (TTA) control

TAPPI Journal ◽  
2018 ◽  
Vol 17 (05) ◽  
pp. 261-269
Author(s):  
Wei Ren ◽  
Brennan Dubord ◽  
Jason Johnson ◽  
Bruce Allison
Keyword(s):  
Feedback Control ◽  
Current Practice ◽  
Feedforward Control ◽  
Control Variable ◽  
Indirect Measurement ◽  
Tight Control ◽  
Transfer Lines ◽  
Green Liquor ◽  
Process Dynamics ◽  
Downstream Processes

Tight control of raw green liquor total titratable alkali (TTA) may be considered an important first step towards improving the overall economic performance of the causticizing process. Dissolving tank control is made difficult by the fact that the unknown smelt flow is highly variable and subject to runoff. High TTA variability negatively impacts operational costs through increased scaling in the dissolver and transfer lines, increased deadload in the liquor cycle, under- and over-liming, increased energy consumption, and increased maintenance. Current practice is to use feedback control to regulate the TTA to a target value through manipulation of weak wash flow while simultaneously keeping dissolver density within acceptable limits. Unfortunately, the amount of variability reduction that can be achieved by feedback control alone is fundamentally limited by the process dynamics. One way to improve upon the situation would be to measure the smelt flow and use it as a feedforward control variable. Direct measurement of smelt flow is not yet possible. The use of an indirect measurement, the dissolver vent stack temperature, is investigated in this paper as a surrogate feedforward variable for dissolving tank TTA control. Mill trials indicate that significant variability reduction in the raw green liquor TTA is possible and that the control improvements carry through to the downstream processes.

scholarly journals Evaluation of Process Control Schemes for Sour Water Strippers in Petroleum Refining

Processes ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 363
Author(s):  
Chii-Dong Ho ◽  
Yih-Hang Chen ◽  
Chao-Min Chang ◽  
Hsuan Chang
Keyword(s):  
Feedback Control ◽  
Prediction Models ◽  
Feedforward Control ◽  
Absolute Error ◽  
Dynamic Responses ◽  
Control Schemes ◽  
Online Measurements ◽  
Measurement Delay ◽  
Water Feed ◽  
Sour Water

For the sour water strippers in petroleum refinery plants, three prediction models were developed first, including the estimators of sour water feed concentrations using convenient online measurements, the minimum reboiler duty and the corresponding internal temperature at a specific location (Tstage,29). Feedforward control schemes were developed based on these prediction models. Four categories of control schemes, including feedforward, feedback, feedback with external reset, and feedforward-feedback, were proposed and evaluated by the rigorous dynamic simulation model of the sour water stripper for their dynamic responses to the sour water feed stream disturbances. The comparison of control performance, in terms of the settling time, integrated absolute error (IAE) of the NH3 concentration of the stripped sour water and IAE of the specific reboiler duty, reveals that FFT (feedforward control of Tstage,29) and FBA-DT3 (feedback control with 3 min concentration measurement delay) are the best control schemes. The second-best control scheme is FBAT (cascade feedback control of concentration with temperature).

scholarly journals Model-Based Design Approach to Improve Performance Characteristics of Hydrostatic Bearing Using Multivariable Optimization

Mathematics ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 388
Author(s):  
Waheed Ur Rehman ◽  
Xinhua Wang ◽  
Yiqi Cheng ◽  
Yingchun Chen ◽  
Hasan Shahzad ◽  
...  
Keyword(s):  
Mathematical Model ◽  
Feedback Control ◽  
External Load ◽  
Sliding Mode ◽  
Feedforward Control ◽  
Spindle Speed ◽  
Performance Criteria ◽  
Model Based ◽  
Hydrostatic Bearings ◽  
Robust Control Design

Research in the field of tribo-mechatronics has been gaining popularity in recent decades. The objective of the current research is to improve static/dynamics characteristics of hydrostatic bearings. Hydrostatic bearings always work in harsh environmental conditions that effect their performance, and which may even result in their failure. The current research proposes a mathematical model-based system for hydrostatic bearings that helps to improve its static/dynamic characteristics under varying conditions of performance-influencing variables such as temperature, spindle speed, external load, and clearance gap. To achieve these objectives, the capillary restrictors are replaced with servo valves, and a mathematical model is developed along with robust control design systems. The control system consists of feedforward and feedback control techniques that have not been applied before for hydrostatic bearings in the published literature. The feedforward control tries to remove a disturbance before it enters the system while feedback control achieves the objective of disturbance rejection and improves steady-state characteristics. The feedforward control is a trajectory-based controller and the feedback controller is a sliding mode controller with a PID sliding surface. The particle swarm optimization algorithm is used to tune the 6-dimensional vector of the tuning parameters with multi-objective performance criteria. Numerical investigations have been carried out to check the performance of the proposed system under varying conditions of viscosity, clearance gap, external load and the spindle speed. The comparison of our results with the published literature shows the effectiveness of the proposed system.

scholarly journals A peduncle detection method of tomato for autonomous harvesting

2021 ◽  
Author(s):  
Jiacheng Rong ◽  
Guanglin Dai ◽  
Pengbo Wang
Keyword(s):  
Pose Estimation ◽  
Pitch Angle ◽  
Detection Method ◽  
Geometric Model ◽  
Average Error ◽  
Long Distance ◽  
End Effector ◽  
Key Points ◽  
Yaw Angle ◽  
Cutting Point

AbstractFor automating the harvesting of bunches of tomatoes in a greenhouse, the end-effector needs to reach the exact cutting point and adaptively adjust the pose of peduncles. In this paper, a method is proposed for peduncle cutting point localization and pose estimation. Images captured in real time at a fixed long-distance are detected using the YOLOv4-Tiny detector with a precision of 92.7% and a detection speed of 0.0091 s per frame, then the YOLACT +  + Network with mAP of 73.1 and a time speed of 0.109 s per frame is used to segment the close-up distance. The segmented peduncle mask is fitted to the curve using least squares and three key points on the curve are found. Finally, a geometric model is established to estimate the pose of the peduncle with an average error of 4.98° in yaw angle and 4.75° in pitch angle over the 30 sets of tests.

Sign in / Sign up

Export Citation Format

Share Document