scholarly journals Experimental and Numerical Assessment of Reinforced Concrete Beams with Disturbed Depth

2019 ◽  
Vol 13 (1) ◽  
Author(s):  
A. Hamoda ◽  
A. Basha ◽  
S. Fayed ◽  
K. Sennah
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Ultimate Load ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Shear Reinforcement ◽  
Geometric Properties ◽  
Beam Shape ◽  
Load Carrying ◽  
Ultimate Load Carrying Capacity

AbstractThis paper investigates numerically and experimentally the performance of reinforced concrete (RC) beam with unequal depths subjected to combined bending and shear. Such beams can geometrically be considered for unleveled reinforced concrete (RC) floor slab-beam system. However, it may generate critical disturbances in stress flow at the re-entrant corner (i.e. location of drop in beam depth). This research investigates the use of shear reinforcement and geometric properties to enhance cracking characteristics, yielding, ultimate load-carrying capacity, and exhibiting ductile failure mode. Ten reinforced concrete (RC) beams were constructed and tested experimentally considering the following key parameters: recess length, depth of smaller beam nib, and amount and layout of shear reinforcement at re-entrant corner. Finite element analysis (FEA) with material non-linearity was conducted in two RC beams that were tested experimentally to validate the computer modelling. The FEA models were then extended to conduct a parametric study to investigate the influence of geometric parameters (beam shape and width) and amount and arrangement of shear reinforcement on the structural response. Results confirmed that geometric properties and ratio of shear reinforcement at the re-entrant region significantly affect the behavior of reinforced concrete beam with unequal depths in terms of first cracking, yielding level, ultimate load carrying capacity and mode of failure.

Numerical Analysis for Reinforced Concrete Beams with Circular Openings in Flexural and Shear Zones Strengthened by Steel Plates

2018 ◽  
Vol 23 (2) ◽  
pp. 31-48
Author(s):  
Ahmed Ali AL-Dhabyani ◽  
Abdulwahab AL-Ansi
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Ultimate Load ◽  
Shear Zones ◽  
Reinforced Concrete Beams ◽  
Steel Plates ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Study Results ◽  
Load Carrying

In the modern building construction, openings in beams are necessary to accommodate several service pipes and ducts. Due to these openings, high stress concentration occurs at its edges. Local cracks also appear around the openings as a result of the reduction in the beam stiffness, the load carrying capacity and the shear capacity. There are many studies which were conducted to develop and test different strengthening methods for the beams opining to increase the ultimate load capacity of the beams. However, from a practical point of view, it is better to have one strengthening method having the same specifications to be used in both; shear and flexural zones for circular opining beams in buildings. In spite of the prior studies, no study has addressed this issue; therefore, there is a need to study such a case. In this paper, an analytical study was conducted to investigate the behavior of the reinforced concrete (RC) beams with circular openings in flexural and shear zones strengthened by steel plates. A 3D FE modeling (ABAQUS 6.12) software was used to simulate five different specimens of RC beams. The study results showed that when the openings were strengthened by steel plates, the ultimate load carrying capacity increased, but the deflection was decreased when compared to the openings without strengthening. In addition, the model reliability was verified via good agreements between the experimental and numerical results.

Response of Damaged Reinforced Concrete Beams Strengthened with NSM CFRP Strips

2020 ◽  
Vol 857 ◽  
pp. 3-9
Author(s):  
Marwa R. Gaber ◽  
Hayder A. Al-Baghdadi
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Ultimate Load ◽  
Scale Model ◽  
Beam Specimen ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Near Surface ◽  
Cross Sectional Dimension ◽  
Load Carrying

This paper presents a study (experimentally) for strengthening reinforced concrete (RC) beams with Near-Surface-Mounted (NSM) technique. The use of this technique with CFRP strips or rebars is an efficient technology for increasing the strength for flexure and shear or for repairing damaged reinforced concrete (RC) members. The objective of this research is to study, experimentally, RC beams either repaired or strengthened with NSM CFRP strips and follow their flexural behavior and failure modes. NSM-CFRP strips were used to strengthen three RC beam specimens, one of them was initially strengthened and tested up to failure. Four beam specimens have been initially subjected to preloading to 50% and 80% of ultimate load. Two of the specimens were either repaired or strengthened with NSM-CFRP strips. All the repaired/strengthened pre-damaged beams have been tested up to failure by using compression-testing machine. An appropriate-scale model was adopted. All the specimens have a cross-sectional dimension of 150 mm with an effective span of 110 mm. Depends on the experimental results, a better performance of the strengthened concrete specimens was obtained in both strength and serviceability. As a comparison with the control beam specimen, all the repaired specimens show a very good increase of about 40% in the load-carrying capacity and a high improvement in resistance to cracking of about 120% in NSM. On the other hand, the test results of NSM CFRP-strengthened concrete specimens with a preloading of 50% and 80% of the ultimate load show an increase of about 9% to 20% in the load-carrying capacity, for 50% and 80% pre-loading, respectively an improvement in deflection of about 2% to 27% in NSM, for 80% and 50% pre-loading, respectively.

EFFECTS OF WEB OPENINGS ON SHEAR BEHAVIOUR OF NORMAL AND INTERNALLY STRENGTHENED CONCRETE BEAMS

2021 ◽  
Author(s):  
Burhan Ahmad ◽  
Muhammad Yousaf ◽  
Muhammad Irfan-ul-Hassan ◽  
Muhammad Burhan Sharif ◽  
Zahid Ahmed Siddiqi ◽  
...  
Keyword(s):  
Ultimate Strength ◽  
Carrying Capacity ◽  
Ultimate Load ◽  
Shear Zones ◽  
Shear Behaviour ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Shear Reinforcement ◽  
Web Openings ◽  
Load Carrying

Web openings in reinforced concrete (RC) beams are provided to pass utility pipes and ducts through them. This causes high stresses (with local cracking) around the transverse web openings, which may lead to reduction in ultimate strength and stiffness of RC beams. Internal strengthening with shear reinforcement can increase ultimate strength of the beam with web openings. This paper presents an experimental study which was conducted to investigate load carrying capacity, mid-span deflection and failure modes of beams with web openings. A total of eighteen RC beams were included in the testing programme, which were tested under two-point loading. The beams contained both pre-planned and post-planned web openings. Experimental results showed that ultimate load of the beams decreased from forty-two to sixty-seven percent due to the presence of web openings in the shear zones. Shear strength of the beams with pre-planned web openings increased by thirty-six percent and one-hundred two percent as compared to the reference beam due to the increase of shear reinforcement by one-hundred twenty-two percent and three-hundred three percent, respectively. Similarly, increase in shear capacity up to six percent and fourteen percent was found for the beams with post-planned web openings due to the aforementioned increase in the area of shear reinforcement, respectively. The ultimate load carrying capacity was also compared with the theoretical models. Internal strengthening and pre planned opening were found effective for providing web openings in the beams.

scholarly journals Strengthening of Reinforced Concrete Beams Weak in Shear Using GFRP

2018 ◽  
Vol 7 (2.20) ◽  
pp. 306
Author(s):  
Qudhan Shaik ◽  
P Polu Raju
Keyword(s):  
Carrying Capacity ◽  
Shear Behavior ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Shear Reinforcement ◽  
Existing Structures ◽  
Load Carrying ◽  
Lateral Strength ◽  
Ultimate Load Carrying Capacity

Due to lateral forces acting on the structure, stresses are generated in the beam which causes beam failure. To overcome those stresses in the existing structures, retrofitting is one of the techniques to increase the lateral strength. In this study, an experimental investigation was done on RC beams to check the shear behavior by comparing control RC beams with strengthened RC beams. To observe the shear behavior considered RC Beams were made weak in shear and then Retrofitted. Two sets of beams were considered, out of which, set-1 consists of three control specimens with shear reinforcement of 100%, 50%, and 30%. Set-2 consists of three retrofitted specimens with GFRP Strips with shear reinforcement of 100%, 50%, and 30%. GFRP strips were provided around the beam with different spacing. The results concluded that the retrofitted specimens have more load carrying capacity compared to control specimens. Thus, the retrofitting is a feasible solution to overcome the stresses developed in the structure. The study also involves the behavior of shear having several GFRP layers and orientation of ultimate load carrying capacity, failure mode and crack pattern of the beam are also investigated.  

scholarly journals Eigenproblem Versus the Load-Carrying Capacity of Hybrid Thin-Walled Columns with Open Cross-Sections in the Elastic Range

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3468
Author(s):  
Zbigniew Kolakowski ◽  
Andrzej Teter
Keyword(s):  
Cross Sections ◽  
Carrying Capacity ◽  
Ultimate Load ◽  
Equilibrium Path ◽  
Load Carrying Capacity ◽  
Nonlinear Buckling ◽  
Elastic Range ◽  
Load Carrying ◽  
Thin Walled ◽  
Ultimate Load Carrying Capacity

The phenomena that occur during compression of hybrid thin-walled columns with open cross-sections in the elastic range are discussed. Nonlinear buckling problems were solved within Koiter’s approximation theory. A multimodal approach was assumed to investigate an effect of symmetrical and anti-symmetrical buckling modes on the ultimate load-carrying capacity. Detailed simulations were carried out for freely supported columns with a C-section and a top-hat type section of medium lengths. The columns under analysis were made of two layers of isotropic materials characterized by various mechanical properties. The results attained were verified with the finite element method (FEM). The boundary conditions applied in the FEM allowed us to confirm the eigensolutions obtained within Koiter’s theory with very high accuracy. Nonlinear solutions comply within these two approaches for low and medium overloads. To trace the correctness of the solutions, the Riks algorithm, which allows for investigating unsteady paths, was used in the FEM. The results for the ultimate load-carrying capacity obtained within the FEM are higher than those attained with Koiter’s approximation method, but the leap takes place on the identical equilibrium path as the one determined from Koiter’s theory.

Experimental study on the axial compression performance of GFRP-reinforced concrete square columns

2018 ◽  
Vol 22 (7) ◽  
pp. 1554-1565 ◽  
Author(s):  
Jianwei Tu ◽  
Kui Gao ◽  
Lang He ◽  
Xinping Li
Keyword(s):  
Carrying Capacity ◽  
Ultimate Load ◽  
Fiber Reinforced Polymer ◽  
Load Carrying Capacity ◽  
Longitudinal Reinforcement ◽  
Rc Columns ◽  
Compression Performance ◽  
Reinforced Polymer ◽  
Load Carrying ◽  
Ultimate Load Carrying Capacity

At present, extensive studies have been conducted relative to the topic of fiber-reinforced polymer(FRP)- reinforced concrete (RC) flexural members, and many design methods have also been introduced. There have, however, been few studies conducted on the topic of FRP-RC compression members. In light of this, eight glass-fiber-reinforced polymer (GFRP)-RC square columns (200×200×600 mm) were tested in order to investigate their axial compression performance. These columns were reinforced with GFRP longitudinal reinforcement and confined GFRP stirrup. These experiments investigated the effects of the longitudinal reinforcement ratio, stirrup configuration (spirals versus hoops) and spacing on the load-carrying capacity and failure modes of GFRP-RC rectangular columns. The test results indicate that the load-carrying capacity of longitudinal GFRP bars accounted for 3%-7% of the ultimate load-carrying capacity of the columns. The ultimate load-carrying capacity of RC columns confined with GFRP spirals increased by 0.8%-1.6% with higher ductility, compared to GFRP hoops. Reducing the stirrup spacing may prevent the buckling failure of the longitudinal bars and increase the ductility and load-carrying capacity of the GFRP-RC columns. It has been found that setting the GFRP compressive strength to 35% of the GFRP maximum tensile strength yields a reasonable estimate of ultimate load-carrying capacity of GFRP-RC columns.

Structural Performance of Fiber-Reinforced Polymer Honeycomb Sandwich Panels: Evaluation of Size Effect and Wrap Strengthening

2003 ◽  
Vol 1845 (1) ◽  
pp. 191-199 ◽  
Author(s):  
Ondrej Kalny ◽  
Robert J. Peterman ◽  
Guillermo Ramirez ◽  
C. S. Cai ◽  
Dave Meggers
Keyword(s):  
Carrying Capacity ◽  
Ultimate Load ◽  
Sandwich Panels ◽  
Fiber Reinforced Polymer ◽  
Load Carrying Capacity ◽  
Flexural Capacity ◽  
Reinforced Polymer ◽  
Load Carrying ◽  
Honeycomb Sandwich ◽  
Ultimate Load Carrying Capacity

Stiffness and ultimate load-carrying capacities of glass fiber-reinforced polymer honeycomb sandwich panels used in bridge applications were evaluated. Eleven full-scale panels with cross-section depths ranging from 6 to 31.5 in. (152 to 800 mm) have been tested to date. The effect of width-to-depth ratio on unit stiffness was found to be insignificant for panels with a width-to-depth ratio between 1 and 5. The effect of this ratio on the ultimate flexural capacity is uncertain because of the erratic nature of core-face bond failures. A simple analytical formula for bending and shear stiffness, based on material properties and geometry of transformed sections, was found to predict service-load deflections within 15% accuracy. Although some factors influencing the ultimate load-carrying capacity were clearly identified in this study, a reliable analytical prediction of the ultimate flexural capacity was not attained. This is because failures occur in the bond material between the outer faces and core, and there are significant variations in bond properties at this point due to the wet lay-up process, even for theoretically identical specimens. The use of external wrap layers may be used to shift the ultimate point of failure from the bond (resin) material to the glass fibers. Wrap serves to strengthen the relatively weak core–face interface and is believed to bring more consistency in determining the ultimate load-carrying capacity.

scholarly journals Flexural strengthening of Reinforced Concrete (RC) Beams Retrofitted with Corrugated Glass Fiber Reinforced Polymer (GFRP) Laminates

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
N. Aravind ◽  
Amiya K. Samanta ◽  
Dilip Kr. Singha Roy ◽  
Joseph V. Thanikal
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Fiber Reinforced Polymer ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Glass Fiber Reinforced Polymer ◽  
Flexural Strengthening ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Load Carrying

AbstractStrengthening the structural members of old buildings using advanced materials is a contemporary research in the field of repairs and rehabilitation. Many researchers used plain Glass Fiber Reinforced Polymer (GFRP) sheets for strengthening Reinforced Concrete (RC) beams. In this research work, rectangular corrugated GFRP laminates were used for strengthening RC beams to achieve higher flexural strength and load carrying capacity. Type and dimensions of corrugated profile were selected based on preliminary study using ANSYS software. A total of twenty one beams were tested to study the load carrying capacity of control specimens and beams strengthened with plain sheets and corrugated laminates using epoxy resin. This paper presents the experimental and theoretical study on flexural strengthening of Reinforced Concrete (RC) beams using corrugated GFRP laminates and the results are compared. Mathematical models were developed based on the experimental data and then the models were validated.

Sign in / Sign up

Export Citation Format

Share Document