Development of Steel Dual-Core Self-Centering Braces: Quasi-Static Cyclic Tests and Finite Element Analyses

2015 ◽  
Vol 31 (1) ◽  
pp. 247-272 ◽  
Author(s):  
Chung-Che Chou ◽  
Ying-Chuan Chen
Keyword(s):  
Finite Element ◽  
Low Cycle Fatigue ◽  
Design Procedure ◽  
Fatigue Tests ◽  
Finite Element Analyses ◽  
Axial Deformation ◽  
Cyclic Tests ◽  
Element Analysis ◽  
Core Self ◽  
Dual Core

This work presents mechanics, tests, and finite element analyses of a novel steel dual-core self-centering brace (SCB) with flag-shaped re-centering responses. The axial deformation capacity of the brace is doubled with respect to the SCED brace by serial deformations of two sets of parallel tensioning elements when both braces use the same tensioning elements. The mechanics of the brace is first explained; six tensioning elements and four dual-core SCBs are tested to evaluate their cyclic performance. The braces exhibit excellent performance up to a drift of 2% with a maximum axial force around 1,400 kN. The braces also survive 15 low-cycle fatigue tests at a drift of 1.5%. Tensioning elements fail when the braces are overloaded to 2.5–3% drift. Finite element analysis is conducted to further verify hysteretic responses of the dual-core SCB in cyclic tests. A design procedure for the proposed dual-core SCB is also included in the paper.

Low Cycle Fatigue Tests and Simulations on Steel Elbows

2013 ◽  
Author(s):  
Patricia Pappa ◽  
George E. Varelis ◽  
Spyros A. Karamanos ◽  
Arnold M. Gresnigt
Keyword(s):  
Finite Element ◽  
Low Cycle Fatigue ◽  
Local Strain ◽  
Fatigue Behaviour ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Element Analysis ◽  
Out Of Plane ◽  
Strain Gauge Measurements ◽  
Number Of Cycles

In this paper the low cycle fatigue behaviour of steel elbows under strong cyclic loading conditions (in-plane and out-of-plane) is examined. The investigation is conducted through advanced finite element analysis tools, supported by real-scale test data for in-plane bending. The numerical results are successfully compared with the experimental measurements. In addition, a parametric study is conducted, which is aimed at investigating the effects of the diameter-to-thickness ratio on the low-cycle fatigue of elbows, focusing on the stress and strain variations. Strain gauge measurements are compared with finite element models. Upon calculation of local strain variation at the critical location, the number of cycles to fracture can be estimated.

Evaluation on Thermo-Mechanical Fatigue Life of IN738LC Using Finite Element Analysis

2013 ◽  
Vol 467 ◽  
pp. 20-23
Author(s):  
Jeong Min Lee ◽  
Dong Keun Lee ◽  
Jae Mean Koo ◽  
Chang Sung Seok
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Strain Amplitude ◽  
Low Cycle Fatigue ◽  
Hysteresis Loops ◽  
Fatigue Tests ◽  
Plastic Strain Amplitude ◽  
Element Analysis ◽  
Mechanical Fatigue ◽  
Super Alloy

In this paper, thermo-mechanical fatigue tests were performed for the nickel-based super alloy IN738LC, after which the thermo-mechanical fatigue life was evaluated using finite element analysis. Nickel-based super alloy is used as the main material of turbine blades, which are important equipment in thermal power generation plants. In general, such materials receive three types of damage under thermo-mechanical fatigue loading. In the case of low-cycle fatigue behavior in which large plastic deformation mainly occurs, the lifetime can be decided by its relationship with the plastic strain amplitude. In order to obtain the plastic strain amplitude from the measured strain amplitude, a hysteresis loop should be derived. However, low-cycle fatigue tests are difficult. Moreover, precise experimental techniques are required to obtain the hysteresis loops. In this study, after thermo-mechanical fatigue tests were performed, thermal mechanical fatigue tests on IN738LC were simulated using finite element analysis. The results of analysis were verified by comparing with the hysteresis loops of an experiment

Biaxial Ratcheting and Cyclic Plasticity for Bree-Type Loading—Part II: Comparison Between Finite Element Analysis and Theory

1996 ◽  
Vol 118 (2) ◽  
pp. 161-167 ◽  
Author(s):  
C. Nadarajah ◽  
H. W. Ng
Keyword(s):  
Finite Element ◽  
Close Agreement ◽  
Design Procedure ◽  
Cyclic Stress ◽  
Analytical Models ◽  
Cyclic Plasticity ◽  
Finite Element Analyses ◽  
Element Analysis ◽  
Extensive Program ◽  
Walled Cylinder

In Part I of this two part paper (Ng and Nadarajah, 1996), the results of an extensive program of finite element analyses were described. The problem being considered is the phenomenon of ratcheting and cyclic stress-strain hysteresis loop behavior in a thin-walled cylinder subject to cyclic thermal stress and sustained internal pressure. The purpose of Part II is to compare the finite element results with two analytical solutions and review the applicability of the latter as a design procedure for assessment of these types of structures. The comparison shows that the ratcheting to shakedown boundaries based on F.E. and analytical models are in close agreement. The hoop ratcheting rates predicted by the uniaxial model enveloped the F.E. and biaxial models, while for the axial ratcheting rates, the F.E. results are upper bound.

Application of Computational Mechanics to Tire Design—Yesterday, Today, and Tomorrow

2011 ◽  
Vol 39 (4) ◽  
pp. 223-244 ◽  
Author(s):  
Y. Nakajima
Keyword(s):  
Finite Element ◽  
New Technologies ◽  
Computational Mechanics ◽  
Design Procedure ◽  
Side Wall ◽  
Rolling Resistance ◽  
Optimization Techniques ◽  
Stress Strain ◽  
Element Analysis ◽  
Crown Shape

Abstract The tire technology related with the computational mechanics is reviewed from the standpoint of yesterday, today, and tomorrow. Yesterday: A finite element method was developed in the 1950s as a tool of computational mechanics. In the tire manufacturers, finite element analysis (FEA) was started applying to a tire analysis in the beginning of 1970s and this was much earlier than the vehicle industry, electric industry, and others. The main reason was that construction and configurations of a tire were so complicated that analytical approach could not solve many problems related with tire mechanics. Since commercial software was not so popular in 1970s, in-house axisymmetric codes were developed for three kinds of application such as stress/strain, heat conduction, and modal analysis. Since FEA could make the stress/strain visible in a tire, the application area was mainly tire durability. Today: combining FEA with optimization techniques, the tire design procedure is drastically changed in side wall shape, tire crown shape, pitch variation, tire pattern, etc. So the computational mechanics becomes an indispensable tool for tire industry. Furthermore, an insight to improve tire performance is obtained from the optimized solution and the new technologies were created from the insight. Then, FEA is applied to various areas such as hydroplaning and snow traction based on the formulation of fluid–tire interaction. Since the computational mechanics enables us to see what we could not see, new tire patterns were developed by seeing the streamline in tire contact area and shear stress in snow in traction.Tomorrow: The computational mechanics will be applied in multidisciplinary areas and nano-scale areas to create new technologies. The environmental subjects will be more important such as rolling resistance, noise and wear.

Design and Analysis of Viscoelastic Seismic Dampers

2002 ◽  
Author(s):  
N. Shimizu ◽  
H. Nasuno ◽  
T. Yazaki ◽  
K. Sunakoda
Keyword(s):  
Finite Element ◽  
Constitutive Relation ◽  
Time Domain ◽  
Dynamic Properties ◽  
Design Procedure ◽  
Fe Analysis ◽  
Damping Capacity ◽  
Element Formulation ◽  
Element Analysis ◽  
Equivalent Viscous Damping

This paper describes a methodology of design and analysis of viscoelastic seismic dampers by means of the time domain finite element analysis. The viscoelastic constitutive relation of material incorporating with the fractional calculus has been derived and the finite element formulation based on the constitutive relation has been developed to analyze the dynamic property of seismic damper. A time domain computer program was developed by using the formulation. Dynamic properties of hysteresis loop, damping capacity, equivalent viscous damping coefficient, and equivalent spring constant are calculated and compared with the experimental results. Remarkable correlation between the FE analysis and the experiment is gained, and consequently the design procedure with the help of the FE analysis has been established.

Investigation on endurance evaluation of a portal crane: experimental, theoretical and finite element analysis

2020 ◽  
Vol 62 (4) ◽  
pp. 357-364
Author(s):  
Yusuf Aytaç Onur ◽  
Hakan Gelen
Keyword(s):  
Finite Element ◽  
Critical Points ◽  
Maximum Stress ◽  
Strain Gages ◽  
Finite Element Analyses ◽  
Element Analysis ◽  
Element Simulation ◽  
Main Girder ◽  
Stressed Component ◽  
Portal Crane

Abstract In this study, the stress on portal crane components at various payloads has been investigated theoretically, numerically and experimentally. The portal crane was computer-aided modeled and finite element analyses were performed so that the most stressed points at the each trolley position investigated on the main girder could be determined. In addition, the critical points were marked on the portal crane, and strain gages were attached to the those critical points so that stress values could be experimentally determined. The safety factor values at different payloads were determined by using finite element simulation. Results indicate that the most stressed component in the examined portal crane is the main girder. Experimental results indicate that the maximum stress value on the main girder is 3.05 times greater than the support legs and 8.99 times larger than the rail.

scholarly journals Simulating sauropod manus-only trackway formation using finite-element analysis

2010 ◽  
Vol 7 (1) ◽  
pp. 142-145 ◽  
Author(s):  
P. L. Falkingham ◽  
K. T. Bates ◽  
L. Margetts ◽  
P. L. Manning
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Surface Area ◽  
Fossil Record ◽  
Temporal Correlation ◽  
Finite Element Analyses ◽  
Centre Of Mass ◽  
Element Analysis ◽  
Mass Distributions ◽  
Track Formation

The occurrence of sauropod manus-only trackways in the fossil record is poorly understood, limiting their potential for understanding locomotor mechanics and behaviour. To elucidate possible causative mechanisms for these traces, finite-element analyses were conducted to model the indentation of substrate by the feet of Diplodocus and Brachiosaurus . Loading was accomplished by applying mass, centre of mass and foot surface area predictions to a range of substrates to model track formation. Experimental results show that when pressure differs between manus and pes, as determined by the distribution of weight and size of respective autopodia, there is a range of substrate shear strengths for which only the manus (or pes) produce enough pressure to deform the substrate, generating a track. If existing reconstructions of sauropod feet and mass distributions are correct, then different taxa will produce either manus- or pes-only trackways in specific substrates. As a result of this work, it is predicted that the occurrence of manus- or pes-only trackways may show geo-temporal correlation with the occurrence of body fossils of specific taxa.

Structural Stability Evaluation for Lifting Lug Design of Large Marine Engine by Finite Element Analysis

2007 ◽  
Vol 353-358 ◽  
pp. 2855-2859
Author(s):  
W.C. Lee ◽  
Chae Sil Kim ◽  
J.B. Na ◽  
D.H. Lee ◽  
S.Y. Cho ◽  
...  
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Design Procedure ◽  
Steel Structures ◽  
Stability Evaluation ◽  
Element Analysis ◽  
Marine Engines ◽  
Dimensional Finite Element ◽  
The Stability ◽  
Three Dimensional Finite Element

Since most marine engines are generally very huge and heavy, it is required to keep safety from accidents in dealing them. Several types of lifting lugs have been used to assemble hundred ton–large steel structures and carry the assembled engines. Recently a few crashes have been occurred in carrying engines due to breaking down the lugs. Although the stability evaluation of the lifting lug has therefore been very important for safety, systematic design procedure of the lugs, which includes the structural analysis considering stability, has few reported. This paper describes the three dimensional finite element structural modeling for a lifting lug, the studies for determining the reasonable loading and boundary conditions, and the stability evaluation with the results of structural analyses. It should be very helpful for designing the other types of lifting lugs with safety.

Influence of backing materials towards the fatigue strength of butt-welded joints

2011 ◽  
Vol 225 (8) ◽  
pp. 1798-1807 ◽  
Author(s):  
M H Kim ◽  
H J Kim ◽  
J H Han ◽  
J M Lee ◽  
Y D Kim ◽  
...  
Keyword(s):  
Finite Element ◽  
Fatigue Strength ◽  
Welded Joints ◽  
Fatigue Tests ◽  
Experimental Results ◽  
Finite Element Analyses ◽  
Cold Metal Transfer ◽  
Notch Stress ◽  
Effective Notch Stress ◽  
Cold Metal

The purpose of this study is to investigate the fatigue strength of butt-welded joints with special attention paid to employing different kinds of backing plates. The effect of the under-matched weld was also considered. Four different cases of backing scenarios for butt-welded specimens such as steel backing, ceramic backing, CMT (no backing by cold metal transfer) and UM (under-matched welded specimen) were investigated. A series of fatigue tests was performed to compare the fatigue strength of butt-welded joints with respect to different backing scenarios. Effective notch stress was used for the interpretation of fatigue strength of butt-welded specimens with backing plates based on finite element analyses for calculating fatigue notch factors. When results were presented from the effective notch stress, all backing scenarios considered in this study exhibited the fatigue strengths corresponding to the FAT 225 curve. From the experimental results of this study, it was determined that the fatigue strengths of butt-welded joints were found to be in the order of CMT, ceramic backing, UM, and steel backing. No significant decrease in fatigue strength, however, was observed when backing plates were steel backing and ceramic backing types.

Failure Analysis of Thinned Wall Elbows Under Excessive Seismic Loading

2002 ◽  
Author(s):  
Masaki Shiratori ◽  
Yoji Ochi ◽  
Izumi Nakamura ◽  
Akihito Otani
Keyword(s):  
Finite Element ◽  
Fatigue Damage ◽  
Failure Modes ◽  
Low Cycle Fatigue ◽  
Local Buckling ◽  
Seismic Loading ◽  
Cycle Fatigue ◽  
Finite Element Analyses ◽  
Residual Thickness ◽  
Limited Period

A series of finite element analyses has been carried out in order to investigate the failure behaviors of degraded bent pipes with local thinning against seismic loading. The sensitivity of such parameters as the residual thickness, locations and width of the local thinning to the failure modes such as ovaling and local buckling and to the low cycle fatigue damage has been studied. It has been found that this approach is useful to make a reasonable experimental plan, which has to be carried out under the condition of limited cost and limited period.

Sign in / Sign up

Export Citation Format

Share Document