Sticky and Collapse Temperature

Author(s):  
Benu Adhikari ◽  
Bhesh Bhandari
Keyword(s):  
2004 ◽  
Vol 18 (15) ◽  
pp. 2123-2139 ◽  
Author(s):  
BIN XUE ◽  
JUN WANG ◽  
WEI WANG

We study the "folding" behaviors of homopolymers with one end fixed. By using canonical ensemble molecular dynamics simulation method, we observe the conformational changes during folding processes. Long chains collapse to the helical nuclei, then regroup to helix from the free-end to form the compact conformations through the middle stages of helix-like coil and helix-like cone, while short chains do not apparently have the above mentioned middle stages. Through simulated annealing, the native conformation of homopolymer chain in our model is found to be helix. We show the relations between specific heat C v (T) and radius of gyration R g (T) as functions of temperature, chain length and the interaction strength, respectively. We find that these two quantities match well and can be combined to interpret the "folding" process of the homopolymer. It is found that the collapse temperature Tθ and the native-like folding temperature T f do not change with the chain length in our model, however the interaction strength affects the values of Tθ and T f .


2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fuminobu Ozaki ◽  
Takumi Umemura

PurposeIn this study, the bending strength, flexural buckling strength and collapse temperature of small steel specimens with rectangular cross-sections were examined by steady and transient state tests with various heating and deformation rates.Design/methodology/approachThe engineering stress and strain relationships for Japan industrial standard (JIS) SN400 B mild steels at elevated temperatures were obtained by coupon tests under three strain rates. A bending test using a simple supported small beam specimen was conducted to examine the effects of the deformation rates on the centre deflection under steady-state conditions and the heating rates under transient state conditions. Flexural buckling tests using the same cross-section specimen as that used in the bending test were conducted under steady-state and transient-state conditions.FindingsIt was clarified that the bending strength and collapse temperature are evaluated by the full plastic moment using the effective strength when the strain is equal to 0.01 or 0.02 under fast strain rates (0.03 and 0.07 min–1). In contrast, the flexural buckling strength and collapse temperature are approximately evaluated by the buckling strength using the 0.002 offset yield strength under a slow strain rate (0.003 min–1).Originality/valueRegarding both bending and flexural buckling strengths and collapse temperatures of steel members subjected to fire, the relationships among effects of steel strain rate for coupon test results, heating and deformation rates for the heated steel members were minutely investigated by the steady and transient-state tests at elevated temperatures.


2008 ◽  
Vol 20 (1) ◽  
pp. 229-238 ◽  
Author(s):  
Fernanda Fonseca ◽  
Stéphanie Passot ◽  
Olivier Cunin ◽  
Michèle Marin

Author(s):  
Takahiro Arai ◽  
Masahiro Furuya

A high-temperature stainless-steel sphere was immersed into various salt solutions to test film boiling behavior at vapor film collapse. The film boiling behavior around the sphere was observed with a high-speed digital-video camera. Because salt additives enhanced condensation heat transfer, the observed vapor film was thinner. Surface temperature of the sphere was measured. Salt additives increased the quenching (vapor film collapse) temperature, because frequency of direct contact between sphere surface and coolant increased. Quenching temperature rises with increased salt concentration. The quenching temperature, however, approaches a constant value when the slat concentration is close to its saturation concentration. The quenching temperature is well correlated with ion molar concentration, which is a number density of ions, regardless of the type of hydrated salts.


2013 ◽  
Vol 102 (6) ◽  
pp. 1773-1785 ◽  
Author(s):  
Kristyn Greco ◽  
Mircea Mujat ◽  
Kristin L. Galbally-Kinney ◽  
Daniel X. Hammer ◽  
R. Daniel Ferguson ◽  
...  

2006 ◽  
Vol 18 (05) ◽  
pp. 222-228 ◽  
Author(s):  
CHUN-TE TAO ◽  
TAI-HORNG YOUNG

Poly N-isopropylacrylamide (PNIPAAm) is a well-known temperature-sensitive polymer. When the temperature is higher than the lower critical solution temperature (LCST), PNIPAAm aquous solution is cloudy (phase separation occurred). In contrast, when the temperature is lower than the LCST, PNIPAAm is soluble in water (a homogeneous solution). The lower critical solution temperature (LCST) in aqueous solution of PNIPAAm was about 32~33°C. We prepared nano-scaled PNIPAAm particles containing carboxylic group on their surfaces by introducing acrylic acid monomer. The carboxylic groups were applied to conjugate with the amino group of the CD34 antibody. This immuno-conjugate can be applied on targeting the human CD34 positive cells, peripheral blood progenitor cells included, for cell purification and drug controlled release. In order to the active responding of controlled release of the conjugate in the body influenced by temperature, we hope to estimate the shifting of the gel-collapse temperature or cloud point of the immuno-conjugates by dynamic light scattering (DLS) and UV absorption. The results show that the gel-collapse temperature of the nano-particle was not significantly affected by the content of AA between 1.5~5 mol%. However, cloud point of the solution was elevated by the conjugation of CD34 antibody to 37°C. When CD34-conjugated particle was subsequently incorporated with recombinant FLT3-ligand, which is a smaller molecule compare to CD34 antibody, cloud point of the solution was not affected.


Sign in / Sign up

Export Citation Format

Share Document