Experimental investigations on the performance of solar powered cabin air ventilator

2015 ◽  
Vol 12 (6) ◽  
pp. 607-618 ◽  
Author(s):  
Sudhir Chitrapady Vishweshwara ◽  
Jalal Marhoon AL. Dhali

Sultanate of Oman witness a long summer with mostly clear blue skies and typically higher ambient temperatures as seen in other GCC countries. This type of environment warrants the use of high capacity and reliable air conditioning systems, both at resident buildings and vehicles. During summer, cars parked directly under the sun, experience a very high temperature rise inside its cabin in the range of near to 50 °C. This high cabin air temperature often causes thermal discomfort to passengers entering the parked car and also has a serious impact on the cars air-conditioning systems, as it takes longer time to bring back the thermal comfort inside the cabin. The studies also revealed that the high cabin temperature often causes health hazards to occupants, especially to infants. Current research paper, reports an experimental study carried out on a parked car, with instrumentation to identify the various the temperature zones inside the car cabin. This experiential study is aimed to improve the thermal comfort inside the cabin through solar powered cabin air ventilator for effective management of cabin air temperature. The study was carried on a chosen vehicle parked at a set direction and location exposed to day long sunlight at Muscat for considerable period of time. Firstly, the study identified the various temperature zones inside the car cabin and ventilation driven with a 10 Wp solar panel was developed to accomplish the required air exchange inside the cabin, along with continues instantaneous heat rejection through steady air exchange between inside and outside environment. A simple ventilator was developed by means of two fans which drove out the hot trapped air and a secondary fan to cool down the temperature inside the car by providing fresh air for limited time. The experimental investigation showed that the vehicle cabin temperature was typically 10 °C lower when ventilator was turned on. On a typical day on month of May, the cabin air temperatures was approximately 21 °C higher than the ambient air temperature, while with the developed ventilator the difference between the cabin and outside air temperature was reduced by 50% approximately. With the ventilator in operation, it was observed that time taken to reduce the cabin air temperature through vehicle air conditioning system to a satisfactory level was much quicker; typically it took less than the half of the time compared to those values tested without ventilator. Thus indicating, the power saving potential of the developed system as the desired level of thermal comfort can be achieved within the shorter period of time. The reduction in time taken to cool down the cabin temperature to the acceptable limits has direct two fold effects; firstly, the fuel consumption for cooling purpose is reduced and secondly, increased thermal comfort level inside the cars cabin. However, the temperature drop pattern was not similar all around the cabin, due to the varied level of cabin sunlight exposure. Temperature drop at the front of the car was lower than in middle and rear of the car. From the study it can be concluded that, with solar powered ventilator, the temperature inside the car was nearly 10 °C lesser compared to cabin without ventilator and it also helps in to bring back the thermal comfort inside the cabin nearly within half time vis-à-vis cabin without ventilation.

Author(s):  
Ghezlane Halhoul Merabet ◽  
Mohamed Essaaidi ◽  
Driss Benhaddou

Thermal comfort is closely related to the evaluation of heating, ventilation, and air conditioning systems. It can be seen as the result of the perception of the occupants of a given environment, and it is the product of the interaction of a number of personal and environmental factors. Otherwise, comfort issues still do not play an important role in the daily operation of commercial buildings. However, in the workplace, local quality effects, in addition to the health, the productivity that has a significant impact on the performance of the activities. In this regard, researchers have conducted, for decades, investigations related to thermal comfort and indoor environments, which includes developing models and indices through experimentations to establish standards to evaluate comfort and factors and set-up parameters for heating, ventilation, and air conditioning systems. However, to our best knowledge, most of the research work reported in the literature deals only with parameters that are not dynamically tracked. This work aims to propose a prototype for comfort measuring through a wireless sensor network and then presenting a model for thermal comfort prediction. The developed model can be used to set up a heating, ventilation, and air conditioning system to meet the expected comfort level. In particular, the obtained results show that there is a strong correlation between users’ comfort and variables such as age, gender, and body mass index as a function of height and weight.


2018 ◽  
Vol 9 (1) ◽  
pp. 59-63 ◽  
Author(s):  
J. Szabo ◽  
L. Kajtar

It is a prime aim to ensure a suitable comfort level in case of office buildings. The productivity of office employees is directly influenced by the comfort. Thermal discomfort and poor indoor air quality deteriorate the intensity and quality of human work. We investigated the comfort in office buildings with on-site measurements during the summer season. The office buildings were operating with different HVAC (Heating, Ventilating and Air-Conditioning) systems: ducted fan-coil with suspended ceiling, installation, non-ducted fan-coil with floor-mounted installation, active chilled beam with fresh air supply. We evaluated the thermal comfort under PMV (Predicted Mean Vote), PPD (Predicted Percentage of Dissatisfied), the local discomfort based on DR (Draught Rate) and the IAQ (Indoor Air Quality) based on carbon dioxide concentration. The comfort measurements were evaluated. The measurements were evaluated with scientific research methods, comfort categories based on the requirements of CR 1752. The results of this comparison were presented in this article.


2017 ◽  
Vol 54 (3) ◽  
pp. 803-812 ◽  
Author(s):  
Mahdi Deymi-Dashtebayaz ◽  
Mehdi Farahnak ◽  
Mojtaba Moraffa ◽  
Arash Ghalami ◽  
Nima Mohammadi

2018 ◽  
Vol 9 (1) ◽  
pp. 35 ◽  
Author(s):  
Alexander Warthmann ◽  
Daniel Wölki ◽  
Henning Metzmacher ◽  
Christoph van Treeck

To accomplish the current climate goals of the federal republic of Germany, energy efficiency within the building and automotive sector must improve considerably. One possible way to reduce the high amount of energy required for heating, ventilation, and air-conditioning (HVAC) is the introduction of personal climatization systems in combination with the extension of the standardized room air temperature range. Personal systems allow improvements of climatic conditions (heating, cooling, and air quality) within sub-areas of the room instead of conditioning an entire room air volume. In this regard, personal systems are perfectly suitable for locations with local air-conditioning focal points, such as open-plan offices and vehicle cabins, where they substantially improve the energy efficiency of the entire system. This work aims to summarize previously conducted research in the area of personal climatization systems. The investigated local thermal actuators comprise fans for the generation of air movement, ventilators for the improvement of the air quality within the respiratory area of persons, water-conditioned panels for the climatization of persons via longwave radiation and conduction, radiant heaters, and combinations of the systems. Personal systems are superior to mixing ventilation regarding the improvement of the perceived air quality and thermal comfort. Furthermore, the introduced overview shows that personal climatization systems are generally more energy-efficient than conventional air-conditioning and facilitates the extension of the indoor air temperature corridor of the HVAC. Table fans and climatized seats are highly effective in connection with the improvement of personal thermal comfort. The performance of the overwhelming majority of applied personal environmental control systems is user-controlled or depends on a predefined load profile, which is generally defined person independent. Single studies reveal that effectively controlled automated systems have a similar thermal impact on a user’s thermal comfort as user-controlled ones. The implementation of an automated control system is feasible by using novel approaches such as the so-called human-centered closed loop control-platform (HCCLC-platform). The latter contains a central data server which allows asynchronous, bi-directional communication between multi-modal sensor data, user feedback systems, thermal actuators and numerical calculation models used to assess the individual thermal comfort of a person. This enables a continuous and holistic reflection of the thermal situation inside a room and the estimation of the corresponding impact on an individual’s thermal comfort. Considering the measured and simulated thermal state of a single person, the described system is capable of determining body-part-specific energy requirements that are needed to keep the overall thermal comfort level of an individual person on a high level.


2014 ◽  
Vol 493 ◽  
pp. 74-79
Author(s):  
Y.A. Sabtalistia ◽  
S.N.N. Ekasiwi ◽  
B. Iskandriawan

Energy consumption for air conditioning systems (air conditioning system) increased along with the increasing need for fresh air and comfortable in the room especially apartments. FAC system (Floor Air Conditioning) is growing because it is more energy efficient than CAC (Ceiling Air Conditioning) system. However, the position of the AC supply is on the lower level at the FAC system causes draft discomfort becomes greater as air supply closer to the occupants so that thermal comfort can be reduced. Heat mixture of windows, exterior walls, kitchen, and occupants in the studio apartment affect thermal comfort in the room too.This study aims to determine the position of the AC supply which has the best thermal comfort of FAC system in the studio apartment. It can be done by analyzing ADPI (Air Diffusion Performance Index), the distribution of air temperature, wind speed, RH (Relative Humidity), and DR (Draft Risk) to change the position of the AC supply supported by CFD (Computational Fluid Dynamics) simulation.This result prove that AC position 2 (on wall near the kitchen) is more comfortable than AC position 1 (on the bathroom wall) because AC position 2 away from occupied areas, thereby reducing the occurrence of draught discomfort.


2005 ◽  
Vol 16 (4) ◽  
pp. 59-66 ◽  
Author(s):  
V Mittal ◽  
KS Kasana ◽  
NS Thakur

An air-conditioning system utilizing solar energy would generally be more efficient, cost wise, if it was used to provide both heating and cooling requirements in the building it serves. Various solar powered heating systems have been tested extensively, but solar powered air conditioning systems have received very little attention. Solar powered absorption cooling systems can serve both heating and cooling requirements in the building it serves. Many researchers have studied the solar absorption air conditioning system in order to make it economically and technically viable. But still, much more research in this area is needed. This paper will help many researchers working in this area and provide them with fundamental knowledge on absorption systems, and a detailed review on the past efforts in the field of solar absorption cooling systems with the absorption pair of lithium-bromide and water. This knowledge will help them to start the parametric study in order to investigate the influence of key parameters on the overall system performance.


2021 ◽  
pp. 108432
Author(s):  
Peiping Zheng ◽  
Chunxiao Wang ◽  
Yanchen Liu ◽  
Borong Lin ◽  
Huijun Wu ◽  
...  

Author(s):  
Somaye A. Mohamadi ◽  
Abdulraheem J. Ahmed

<span>Despite their complexity and uncertainty, air conditioning systems should provide the optimal thermal conditions in a building. These controller systems should be adaptable to changes in environmental parameters. In most air conditioning systems, today, there are On/Off controllers or PID in more advanced types, which, due to different environmental conditions, are not optimal and cannot provide the optimal environmental conditions. Controlling thermal comfort of an air conditioning system requires estimation of thermal comfort index. In this study, fuzzy controller was used to provide thermal comfort in an air conditioning system, and neural network was used to estimate thermal comfort in the feedback path of the controller. Fuzzy controller has a good response given the non-linear features of air conditioning systems. In addition, the neural network makes it possible to use thermal comfort feedback in a real-time control.</span>


2017 ◽  
Author(s):  
Abhijeet Chothave ◽  
Yashwant Mohite ◽  
Vinay Poal ◽  
Phaneendra Pamarthi

Sign in / Sign up

Export Citation Format

Share Document