Introduction. Currently used grinding machines, among which drum mills are the most widely used, have a low efficiency, are bulky, are characterized by low specific productivity, significant consumption of steel for grinding bodies and lining, high noise level, and high energy consumption of the grinding process. The most promising devices of a new type that can effectively perform grinding operations at high technological rates are centrifugal mills. The centrifugal mill developed at SKGMI operates on the principle of self-grinding of pieces and particles of crushed mineral raw materials, when they collide and RUB in a mobile toroidal flow formed when the material moves between a rotating Cup-shaped rotor, a fixed body and the overlying layers of the crushed material. Grinding occurs due to the appearance of a gradient of particle velocities over the working body, due to their impact and, to a greater extent, abrasion. The tests of these mills for grinding various materials have shown high efficiency in operation, but until now, the issues of determining the physical and mechanical properties of the crushed material based on the establishment of the particle opening mechanism remain unresolved. The purpose of the tests. Determination of the physical and mechanical properties of the crushed material in a centrifugal mill based on the establishment of the particle opening mechanism. Test procedure. To solve this problem, a vertical centrifugal mill MC-600 with a rotor diameter of 600 mm was used. Tests of the centrifugal mill were carried out according to the following method. The speed of rotation of the rotor was 4.8 and 8.4 s-1, the height of the material column above the rotor was at the level of 250 and 350 mm; 6 radial ribs were installed in the rotor cavity of the mill. The time of each test was 4 hours. The tests were repeated 3–5 times for each mode of operation of the mill. Quartz was used as a reference material for determining the relative pulverizability coefficient. The research was carried out in the production conditions of the Izhevsk machinebuilding plant during the regeneration of spent molding quartz mixtures. Pieces of a liquid-glass mixture based on quartz sand with strength of 1.3 MPa and 4.25 MPa were used as the crushed material. The crushed material was dispersed according to the standard method for each hour of operation of the mill. Samples were taken in the size class -0.200 + 0.074 mm for their fractional analysis by size. Test result. 1. It was Found that the maximum productivity of a centrifugal mill when grinding pieces of material with a strength of 1.3 MPa was achieved with a loading weight of 90–100 kg, and with a strength of 4.25 MPa – 100–110 kg, which indicates the need to create an increased normal pressure of the layers of crushed material located above the mill rotor. It was found that the maximum productivity of a centrifugal mill when grinding pieces of material with a strength of 1.3 MPa and a rotor rotation frequency of 8.4 s-1 was 13.16 t/h, and when grinding pieces of material with a strength of 4.25 MPa – 10.0 t/h. 2. The Dependence of power consumption on the weight of the mill load and the rotor speed increases when the load weight is more than 100 kg. 3. The Highest fraction content of class -0.4 +0.16 mm is 72.14 %, and the content of class -0.074 mm is 3.9 %, i.e. there is no re-grinding of the source material. 4. The specific productivity of the centrifugal mill for the newly formed calculated size classes -0.074 mm and -0.200 mm was 1.28 t/h and 13.0 t/h, respectively. 5. Microscopic study of anshlifov showed that quartz grains in the crushed material mostly have a rounded shape, on average 90–95 % of the grains. In the initial material, about 90% of quartz joints with a binder, and in the crushed material, the number of joints does not exceed 3–5%. Thus, the degree of expansion of quartz reaches to 0.87. Conclusions. The paper presents the results of studies of a centrifugal mill in the conditions of the Izhevsk machinebuilding plant when grinding quartz-containing products. The physical and mechanical properties of the crushed material that significantly affect the efficiency of grinding are determined. The mechanism of the disclosure particles of quartz, which is primarily the mineral content of many ores and defined particle size obtained by grinding. At the same time, it was found that a large yield of thin classes significantly reduces the efficiency of further technology.
DETERMINATION OF THE WORKING AREA OF THE EDGE SIEVE OF GRAIN CRUSHER WITH INCREASED SEPARATING SURFACE
