218205 A Study of Reduction of Combustion Products by Using Lean Combustion for a Small Gasoline Engine (3rd report)

2011 ◽  
Vol 2011.17 (0) ◽  
pp. 473-474
Author(s):  
Kunihiro MIZUNO ◽  
Tadashige KAWAKAMI
Author(s):  
Joseph Rabovitser ◽  
Stan Wohadlo ◽  
John M. Pratapas ◽  
Serguei Nester ◽  
Mehmet Tartan ◽  
...  

Paper presents the results from development and successful testing of a 200 kW POGT prototype. There are two major design features that distinguish POGT from a conventional gas turbine: a POGT utilizes a partial oxidation reactor (POR) in place of a conventional combustor which leads to a much smaller compressor requirement versus comparably rated conventional gas turbine. From a thermodynamic perspective, the working fluid provided by the POR has higher specific heat than lean combustion products enabling the POGT expander to extract more energy per unit mass of fluid. The POGT exhaust is actually a secondary fuel gas that can be combusted in different bottoming cycles or used as synthesis gas for hydrogen or other chemicals production. Conversion steps for modifying a 200 kW radial turbine to POGT duty are described including: utilization of the existing (unmodified) expander; replacement of the combustor with a POR unit; introduction of steam for cooling of the internal turbine structure; and installation of a bypass air port for bleeding excess air from the compressor discharge because of 45% reduction in combustion air requirements. The engine controls that were re-configured for start-up and operation are reviewed including automation of POGT start-up and loading during light-off at lean condition, transition from lean to rich combustion during acceleration, speed control and stabilization under rich operation. Changes were implemented in microprocessor-based controllers. The fully-integrated POGT unit was installed and operated in a dedicated test cell at GTI equipped with extensive process instrumentation and data acquisition systems. Results from a parametric experimental study of POGT operation for co-production of power and H2-enriched synthesis gas are provided.


2014 ◽  
Vol 532 ◽  
pp. 362-366 ◽  
Author(s):  
Jiang Feng Mou ◽  
Rui Qing Chen ◽  
Yi Wei Lu

This paper studies the lean burn limit characteristic of the compound injection system of the direct-injection gasoline engine. The low pressure nozzle on the intake manifold can achieve quality homogeneous lean mixture, and the direct injection in the cylinder can realized the dense mixture gas near the spark plug. By adjusting the two injection timing and injection quantity, and a strong intake tumble flow with special shaped combustion chamber, it can produces the reverse tumble to form different hierarchical levels of mixed gas in the cylinder. Experimental results show: the compound combustion system to the original direct-injection engine lean burn limit raise 1.8-2.5 AFR unit.


2021 ◽  
Vol 13 (12) ◽  
pp. 168781402110381
Author(s):  
Li Wang ◽  
Zhaoming Huang ◽  
Wang Tao ◽  
Kai Shen ◽  
Weiguo Chen

EGR and excess-air dilution have been investigated in a 1.5 L four cylinders gasoline direct injection (GDI) turbocharged engine equipped with prechamber. The influences of the two different dilution technologies on the engine performance are explored. The results show that at 2400 rpm and 12 bar, EGR dilution can adopt more aggressive ignition advanced angle to achieve optimal combustion phasing. However, excess-air dilution has greater fuel economy than that of EGR dilution owing to larger in-cylinder polytropic exponent. As for prechamber, when dilution ratio is greater than 37.1%, the combustion phase is advanced, resulting in fuel economy improving. Meanwhile, only when the dilution ratio is under 36.2%, the HC emissions of excess-air dilution are lower than the original engine. With the increase of dilution ratio, the CO emissions decrease continuously. The NOX emissions of both dilution technologies are 11% of those of the original engine. Excess-air dilution has better fuel economy and very low CO emissions. EGR dilution can effectively reduce NOX emissions, but increase HC emissions. Compared with spark plug ignition, the pre chamber ignition has lower HC, CO emissions, and higher NO emissions. At part load, the pre-chamber ignition reduces NOX emissions to 49 ppm.


1996 ◽  
Vol 118 (1) ◽  
pp. 167-172 ◽  
Author(s):  
H. Kumakura ◽  
M. Sasaki ◽  
D. Suzuki ◽  
H. Ichikawa

Performance tests were conducted on a low-emission combustor, which has a pre-vaporization–premixing lean combustion system and is designed for a 100 kW automotive ceramic gas turbine. The results of steady-state combustion tests performed at an inlet temperature of 1000–1200 K and pressure of 0.1–0.34 MPa indicate that the combustor would meet Japan’s emission standards for gasoline engine passenger cars without using an aftertreatment system. Flashback was suppressed by controlling the mixture velocity and air ratios. Strength tests conducted on rings and bars cut from the actual ceramic parts indicate that the combustor has nearly the same level of strength as standard test specimens.


Author(s):  
Junghwan Kim ◽  
Rolf D. Reitz ◽  
Sung Wook Park ◽  
Kian Sung

Experimental and numerical studies were performed to investigate the simultaneous reduction in NOx and CO for stoichiometric diesel combustion with a three-way catalyst. A single-cylinder engine was used for the experiments and KIVA simulations were used in order to characterize the combustion efficiency and emissions of throttled stoichiometric diesel combustion at 0.7 bar boost pressure and 90 MPa injection pressure. In addition, the efficiency of emission conversion with three-way catalysts in stoichiometric diesel combustion was investigated experimentally. The results showed CO and NOx emissions can be controlled with the three-way catalyst in spite of the fact that CO increases more at high equivalence ratios compared with conventional diesel combustion (i.e., lean combustion). At a stoichiometric operation, the three-way catalyst reduced CO and NOx emissions by up to 95%, which achieves lower emissions compared with conventional diesel combustion or low temperature diesel combustion, while keeping better fuel consumption than a comparable gasoline engine.


Energy ◽  
2017 ◽  
Vol 133 ◽  
pp. 366-379 ◽  
Author(s):  
Feng Zhou ◽  
Jianqin Fu ◽  
Wenhui Ke ◽  
Jingping Liu ◽  
Zhipeng Yuan ◽  
...  

2011 ◽  
Vol 84-85 ◽  
pp. 269-273
Author(s):  
Fu Bing You ◽  
Xin Tang Zhang ◽  
Zhi Xiang Pan ◽  
Ge Sheng Li

Hydrous-ethanol is reformed to hydrogen-rich mixture gas which is an excellent fuel for engines. The advantages of this approach are that fossil fuel consumption and CO2 emissions are reduced, and the waste heat from engine exhaust can be used as energy source for hydrous-ethanol evaporating and reforming. The experiment is carried out on a gasoline engine as primary engine with only modest changes. The results indicate that the hydrogen-rich mixture gas allows operation at much higher compression ratio due to its intrinsic octane number which could contribute to the power performance, and the NOx, CO, THC emissions are reduced remarkably because of lean combustion realized in the cylinder.


Sign in / Sign up

Export Citation Format

Share Document