Reduction in NOx and CO Emissions in Stoichiometric Diesel Combustion Using a Three-Way Catalyst

2010 ◽  
Vol 132 (7) ◽  
Author(s):  
Junghwan Kim ◽  
Rolf D. Reitz ◽  
Sung Wook Park ◽  
Kian Sung
Keyword(s):  
Gasoline Engine ◽  
Injection Pressure ◽  
Combustion Efficiency ◽  
Boost Pressure ◽  
Nox Emissions ◽  
Diesel Combustion ◽  
Simultaneous Reduction ◽  
Lean Combustion ◽  
Numerical Studies ◽  
Three Way Catalyst

Experimental and numerical studies were performed to investigate the simultaneous reduction in NOx and CO for stoichiometric diesel combustion with a three-way catalyst. A single-cylinder engine was used for the experiments and KIVA simulations were used in order to characterize the combustion efficiency and emissions of throttled stoichiometric diesel combustion at 0.7 bar boost pressure and 90 MPa injection pressure. In addition, the efficiency of emission conversion with three-way catalysts in stoichiometric diesel combustion was investigated experimentally. The results showed CO and NOx emissions can be controlled with the three-way catalyst in spite of the fact that CO increases more at high equivalence ratios compared with conventional diesel combustion (i.e., lean combustion). At a stoichiometric operation, the three-way catalyst reduced CO and NOx emissions by up to 95%, which achieves lower emissions compared with conventional diesel combustion or low temperature diesel combustion, while keeping better fuel consumption than a comparable gasoline engine.

Reduction of NOx and CO Emissions in Stoichiometric Diesel Combustion Using a 3-Way Catalyst

2009 ◽  
Author(s):  
Junghwan Kim ◽  
Rolf D. Reitz ◽  
Sung Wook Park ◽  
Kian Sung
Keyword(s):  
Gasoline Engine ◽  
Injection Pressure ◽  
Combustion Efficiency ◽  
Boost Pressure ◽  
Nox Emissions ◽  
Diesel Combustion ◽  
Simultaneous Reduction ◽  
Lean Combustion ◽  
Numerical Studies ◽  
Reduction Of Nox

Experimental and numerical studies were performed to investigate the simultaneous reduction of NOx and CO for stoichiometric diesel combustion with a 3-way catalyst. A single-cylinder engine was used for the experiments and KIVA simulations were used in order to characterize the combustion efficiency and emissions of throttled stoichiometric diesel combustion at 0.7 bar boost pressure and 90MPa injection pressure. In addition, the efficiency of emission conversion with the 3-way catalysts in stoichiometric diesel combustion was investigated experimentally. The results showed CO and NOx emissions can be controlled with the 3-way catalyst in spite of the fact that CO increases more at high equivalence ratios compared to conventional diesel combustion (i.e., lean combustion). At stoichiometric operation, the 3-way catalyst reduced CO and NOx emissions by up to 95%, which achieves lower emissions compared to conventional diesel combustion or low temperature diesel combustion, while keeping better fuel consumption than a comparable gasoline engine.

scholarly journals Combustion Optimization for Coal Fired Power Plant Boilers Based on Improved Distributed ELM and Distributed PSO

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1036 ◽  
Author(s):  
Xinying Xu ◽  
Qi Chen ◽  
Mifeng Ren ◽  
Lan Cheng ◽  
Jun Xie
Keyword(s):  
Power Plant ◽  
Combustion Process ◽  
Optimization Method ◽  
Combustion Efficiency ◽  
Pollutant Emissions ◽  
Combustion Model ◽  
Nox Emissions ◽  
Coupling Characteristics ◽  
Learning Machine ◽  
Combustion Optimization

Increasing the combustion efficiency of power plant boilers and reducing pollutant emissions are important for energy conservation and environmental protection. The power plant boiler combustion process is a complex multi-input/multi-output system, with a high degree of nonlinearity and strong coupling characteristics. It is necessary to optimize the boiler combustion model by means of artificial intelligence methods. However, the traditional intelligent algorithms cannot deal effectively with the massive and high dimensional power station data. In this paper, a distributed combustion optimization method for boilers is proposed. The MapReduce programming framework is used to parallelize the proposed algorithm model and improve its ability to deal with big data. An improved distributed extreme learning machine is used to establish the combustion system model aiming at boiler combustion efficiency and NOx emission. The distributed particle swarm optimization algorithm based on MapReduce is used to optimize the input parameters of boiler combustion model, and weighted coefficient method is used to solve the multi-objective optimization problem (boiler combustion efficiency and NOx emissions). According to the experimental analysis, the results show that the method can optimize the boiler combustion efficiency and NOx emissions by combining different weight coefficients as needed.

The Research of Lean Combustion Characteristic of Compound Injection System of Direct Injection Engine

2014 ◽  
Vol 532 ◽  
pp. 362-366 ◽  
Author(s):  
Jiang Feng Mou ◽  
Rui Qing Chen ◽  
Yi Wei Lu
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Injection System ◽  
Intake Manifold ◽  
Combustion Characteristic ◽  
Injection Timing ◽  
Mixed Gas ◽  
Lean Burn ◽  
Direct Injection Engine ◽  
Lean Combustion

This paper studies the lean burn limit characteristic of the compound injection system of the direct-injection gasoline engine. The low pressure nozzle on the intake manifold can achieve quality homogeneous lean mixture, and the direct injection in the cylinder can realized the dense mixture gas near the spark plug. By adjusting the two injection timing and injection quantity, and a strong intake tumble flow with special shaped combustion chamber, it can produces the reverse tumble to form different hierarchical levels of mixed gas in the cylinder. Experimental results show: the compound combustion system to the original direct-injection engine lean burn limit raise 1.8-2.5 AFR unit.

Numerical Studies of Novel Aero Engine Secondary Combustors for Low-NOx Emissions

2020 ◽  
Author(s):  
Andrew Rolt ◽  
Victor Martínez Bueno ◽  
Mirko Romanelli ◽  
Xiaoxiao Sun ◽  
Pierre Gauthier ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Flow Region ◽  
Nox Emissions ◽  
Low Oxygen ◽  
Engine Operation ◽  
Horizon 2020 ◽  
Novel Technologies ◽  
Numerical Studies ◽  
Aero Engine

Abstract Gas turbine thermal efficiency and fuel burn are very dependent on turbine entry temperature and overall pressure ratio (OPR). Unfortunately, increases in these two parameters compromise other key aspects of engine operation and tend to increase emissions of nitrogen oxides (NOx). The European Horizon 2020 ULTIMATE project researched advanced-cycle aero engines with synergistic combinations of novel technologies to increase thermal efficiency without increasing emissions. One candidate technology was the addition of secondary combustion to increase the mean temperature of heat addition to improve thermal efficiency while limiting the primary combustor flame temperatures and NOx formation. However, an overall reduction in NOx also requires the secondary combustor to be a low-NOx design. This paper describes numerical studies carried out on novel aero engine secondary combustor concepts developed in two MSc-thesis research projects. The studies have explored the potential of oxy-poor-flame combustion concepts. These annular combustor designs featured two distinct regions: (i) the vortex zone, which promotes recirculation of combustion products, a prerequisite for low-oxygen combustion, and (ii) a through-flow region where part of the incoming flow bypasses the vortex before the flows mix again. These studies have demonstrated the advantages and some limitations of the proposed designs and emissions assessments in comparison with previous secondary combustor studies. They suggest very low NOx is achievable with oxy-poor combustion, but will be more difficult if the incoming oxygen levels are above 10%. More-accurate assessments will require LES modelling and inclusion of the primary combustor in the simulations. However, if the low overall NOx emissions would include relatively higher levels of nitrous oxide (N2O) then this might raise concerns with respect to global warming.

Economy and emission characteristics of the optimal dilution strategy in lean combustion based on GDI gasoline engine equipped with prechamber

2021 ◽  
Vol 13 (12) ◽  
pp. 168781402110381
Author(s):  
Li Wang ◽  
Zhaoming Huang ◽  
Wang Tao ◽  
Kai Shen ◽  
Weiguo Chen
Keyword(s):  
Fuel Economy ◽  
Gasoline Engine ◽  
Direct Injection ◽  
Engine Performance ◽  
Gasoline Direct Injection ◽  
Dilution Ratio ◽  
Lean Combustion ◽  
Excess Air ◽  
Combustion Phase ◽  
Hc Emissions

EGR and excess-air dilution have been investigated in a 1.5 L four cylinders gasoline direct injection (GDI) turbocharged engine equipped with prechamber. The influences of the two different dilution technologies on the engine performance are explored. The results show that at 2400 rpm and 12 bar, EGR dilution can adopt more aggressive ignition advanced angle to achieve optimal combustion phasing. However, excess-air dilution has greater fuel economy than that of EGR dilution owing to larger in-cylinder polytropic exponent. As for prechamber, when dilution ratio is greater than 37.1%, the combustion phase is advanced, resulting in fuel economy improving. Meanwhile, only when the dilution ratio is under 36.2%, the HC emissions of excess-air dilution are lower than the original engine. With the increase of dilution ratio, the CO emissions decrease continuously. The NOX emissions of both dilution technologies are 11% of those of the original engine. Excess-air dilution has better fuel economy and very low CO emissions. EGR dilution can effectively reduce NOX emissions, but increase HC emissions. Compared with spark plug ignition, the pre chamber ignition has lower HC, CO emissions, and higher NO emissions. At part load, the pre-chamber ignition reduces NOX emissions to 49 ppm.

Sign in / Sign up

Export Citation Format

Share Document