Study on Influences of Flame Temperature on Premixed Flame and End Gas in Process of Knock using Constant Volume Vessel

2016 ◽  
Vol 2016 (0) ◽  
pp. G0700305
Author(s):  
Ryo SHINYA ◽  
Kenta KONO ◽  
Takuro KOTO ◽  
Takuya IISHI ◽  
Shota TANAKA ◽  
...  
2016 ◽  
Vol 2016.69 (0) ◽  
pp. 281-282
Author(s):  
Ryo SHINYA ◽  
Shota TANAKA ◽  
Takuro KOTO ◽  
Takuya IISHI ◽  
Yukihide NAGANO ◽  
...  

2013 ◽  
Vol 750-752 ◽  
pp. 1734-1737
Author(s):  
Jun Xia Zhang ◽  
Bing Biao Yang

Many combustion processes seriously pollute the environment because of producing nitrogen oxides emission, which abstracts wide attention from researchers. How to reduce nitrogen oxides emission is important to protect the environment. At the present work, a reduction mechanism based on a detailed chemical reaction kinetics mechanism, Gri_Mech3.0 was adopted to analyze nitrogen oxides formation in a CH4/air laminar premixed and turbulent diffusion flames, a two dimensional turbulent diffusion flame was simulated with the EDC model. Parameters were obtained, including flame temperature, burning velocity and mass fraction of nitrogen oxides. The results of laminar premixed flame show that nitrogen oxides emission mainly comes from the thermal and prompt NO mechanisms. A large amount of free radicals O, H and OH produced by combustion processes provide reactants for the reactions of nitrogen oxides formation. Mole fraction of nitrogen oxides increases with the increasing of both flame temperature and chemical equivalence ratios. By contrast, there is a lower mass fraction of nitrogen oxides formation for the fuel-lean flame.


2017 ◽  
Vol 2017 (0) ◽  
pp. J0710105
Author(s):  
Yukihide NAGANO ◽  
Kenta KONO ◽  
Ryo SHINYA ◽  
Shota TANAKA ◽  
Toshiaki KITAGAWA

2018 ◽  
Author(s):  
Martia Shahsavan ◽  
Mohammadrasool Morovatiyan ◽  
John Hunter Mack

The ignition behavior of the fuel in non-premixed turbulent combustion applications such as diesel engines and gas turbines is dependent on the mixing rate of the injected fuel and the working fluid. In this study, three-dimensional modeling of hydrogen injection into a constant volume combustion chamber (CVCC) is used to investigate the correlation between the mixing rate and important parameters of non-premixed combustion, such as ignition delay. Mixedness is quantified using mean spatial variation, which reflects the homogeneity of the mixture, and mean scalar dissipation, which represents the local gradients of the scalar. The case studies include nitrogen and argon as working fluids; injection velocities and nozzle diameters are varied for comparison. For consistency, the injected mass is kept constant and the injection duration is adjusted accordingly. The results indicate that a strong correlation exists between ignition delay and the defined mixedness parameters. The cases with higher mixedness values lead to a shorter ignition delay and a higher maximum flame temperature. Changing the working fluid and injection parameters can effectively modify the mixedness, and consequently affect the ignition onset and flame properties.


2015 ◽  
Vol 2015.68 (0) ◽  
pp. 211-212
Author(s):  
Ryo SHINYA ◽  
Takuya IISHI ◽  
Shota TANAKA ◽  
Yukihide NAGANO ◽  
Toshiaki KITAGAWA

Author(s):  
M. Bianco ◽  
S. M. Camporeale ◽  
B. Fortunato

Evaporative cycles, such as Recuperated Water lnjected (RWI) cycle, Humid Air Turbine (HAT) cycle, Cascaded Humidified Advanced Turbine (CHAT) offer the attractive possibility to increase plant efficiency without the use of a steam turbine, necessary for gas-steam combined cycles, appearing, therefore, as an interesting solution for industrial power applications such as electric utilities and independent power producers. It is expected that water addition may contribute to reduce NOx emissions in premixed flame combustors. In order to analyse this solution, a lean-bum combustor, fed with an homogeneous mixture formed by methane and humid air, has been analysed through CFD simulations, in order to predict velocity field, temperatures and emissions. The study has been carried out under the hypothesis of a two-dimensional, axisymmetric combustion chamber assuming, as set of operation conditions, atmospheric pressure, inlet temperature of 650 K, fuel-air equivalence ratio of the methane-air mixture ranging from 0.5 to 0.7 and water-air mass ratio varying from 0% to 5%. In the simulation, the presence of turbulence in the flow has been taken into account using a RNG k-ε model, whilst the chemical behaviour of the system has been described by means of a five-step global reduced mechanism including the oxidation mechanism and the NOx formation mechanism. The analysis of the results shows that the moisture in the premixed flow reduces both NOx and CO emissions at constant equivalence ratio; moreover the lean blow-out limit is shifted toward higher equivalence ratio. The main effect of the water seems to be the increase of the specific heat the mixture which causes a reduction in flame temperature, slowing the chemical reactions responsible of NOx formation. The reasonable agreement has been found between the simulation results concerning NOx emissions and recent experimental results carried out on premixed flamed with humid air. A discussion is also provided about the adopted turbulence models and their influence on the emission results.


RSC Advances ◽  
2015 ◽  
Vol 5 (43) ◽  
pp. 34272-34280 ◽  
Author(s):  
Zhenhua Xie ◽  
Zhongqing Yang ◽  
Li Zhang ◽  
Chuncheng Liu

By means of numerical simulation, this paper presents the effects of non-catalytic surface reactions on flame temperature distribution and radical distribution within a 2D micro planar channel.


Sign in / Sign up

Export Citation Format

Share Document