P-OS2-1 Development of Nano Temperature Sensor Array for Acquisition of Temperature Distribution on the Rake Face of Cutting Tool

2012 ◽  
Vol 2012.4 (0) ◽  
pp. 245-246
Author(s):  
Keigo ISHII ◽  
Tatsuro FURUSHO ◽  
Naohiko SUGITA ◽  
Reo Kometani ◽  
Sunao ISHIHARA ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Temperature Sensor ◽  
Sensor Array ◽  
Cutting Tool ◽  
Rake Face

scholarly journals C13 Development of WC-Cr minimal temperature sensor array integrated with a cutting tool

2010 ◽  
Vol 2010.8 (0) ◽  
pp. 173-174
Author(s):  
Ken YOKOYAMA ◽  
Tatsuro FURUSHO ◽  
Naohiko SUGITA ◽  
Mamoru MITSUISHI
Keyword(s):  
Temperature Sensor ◽  
Sensor Array ◽  
Cutting Tool

scholarly journals Measurement of the Temperature Distribution at the Tool-Chip Interface by Using a Cutting Tool with Seven Pairs of Built-In Micro Cu/Ni Thermocouples

2016 ◽  
Vol 1136 ◽  
pp. 586-591 ◽  
Author(s):  
Jun Shinozuka ◽  
Habibah binti Jaharadak
Keyword(s):  
Aluminum Alloy ◽  
Heat Conduction ◽  
Temperature Distribution ◽  
High Performance ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Rake Face ◽  
Machining Performance ◽  
Unsteady Heat Conduction ◽  
Indexable Insert

Knowing temperatures at the tool-chip interface is extremely important to optimize the machining condition and to improve the machining performance, furthermore to design high performance materials. In order to grasp the temperature distribution at the tool-chip interface, this study has devised an indexable insert with seven pairs of built-in micro Cu/Ni thermocouples on the rake face near the cutting edge. This paper shows the performance of the indexable insert with built-in micro thermocouples developed. The thickness of each element of the micro thermocouple is approximately 15 μm. The result of unsteady heat conduction analysis employing FEM shows that the temperature difference by installing the micro thermocouples is less than 10 K or 1.2 %. The temperature measurement experiments by cutting of aluminum alloy were carried out by changing the cutting speed. The results provided the evidence that the temperature distribution at the tool-chip interface can be grasped with the indexable insert with built-in micro thermocouples developed.

Effect of Rake Face Design on Cutting Tool Temperature Distributions

1980 ◽  
Vol 102 (2) ◽  
pp. 123-128 ◽  
Author(s):  
P. K. Wright ◽  
S. P. McCormick ◽  
T. R. Miller
Keyword(s):  
Temperature Distribution ◽  
Cutting Tool ◽  
Contact Length ◽  
Measured Temperature ◽  
Rake Face ◽  
Low Carbon ◽  
Temperature Distributions ◽  
Metallographic Method ◽  
Carbon Iron ◽  
Good Agreement

Turning experiments have been carried out on a low carbon iron using steel tools of different side rake face geometry. Temperature distributions have been determined using a recently developed metallographic method. It has been found that when using tools which have a controlled chip-tool contact length of 0.5 mm. the temperatures are ∼30 per cent lower than when using conventional, 6 deg rake tools and, as a result, tool life is longer. Theoretical equations are described which allow the calculation of the temperature distribution along the chip tool interface and the tribological conditions in this region are also considered in detail. There is good agreement between the calculated and measured temperature distributions.

Cutting temperature measurement by a micro-sensor array integrated on the rake face of a cutting tool

CIRP Annals ◽  
2015 ◽  
Vol 64 (1) ◽  
pp. 77-80 ◽  
Author(s):  
Naohiko Sugita ◽  
Keigo Ishii ◽  
Tatsuo Furusho ◽  
Kanako Harada ◽  
Mamoru Mitsuishi
Keyword(s):  
Temperature Measurement ◽  
Sensor Array ◽  
Cutting Tool ◽  
Cutting Temperature ◽  
Rake Face ◽  
Micro Sensor

Research on Sticking Failure Characteristics of Cemented Carbide Blade

2012 ◽  
Vol 500 ◽  
pp. 211-217
Author(s):  
Zhe Li ◽  
Min Li Zheng ◽  
Xian Zhi Chen ◽  
Meng Tong
Keyword(s):  
Electron Microscopy ◽  
Cutting Tool ◽  
Influence Factors ◽  
Rake Face ◽  
Tool Breakage ◽  
Failure Characteristics ◽  
Micro Cracks ◽  
Cutting Zone ◽  
Element Density ◽  
Scanning Electron

Through the analysis on damaged tool in sticking failure experiment by cutting austenitic stainless steel (1Cr18Ni9Ti) with scanning electron microscopy (SME), found that there are micro cracks existent on rake face near the tip of the cutting tool, through the research of the emergence, development and distribution direction of the crack, the direct reason for tool breakage is the crack being out of control. Combining the study of cutting tool element density change in cutting zone and grooving wear on rake face, this paper analyzed the cause of the binding between chip and tool and the influence factors of sticking failure during the cutting process.

scholarly journals Fabrication and Performance Evaluation of Thin Film RTD Temperature Sensor Array on a Curved Glass Surface

2011 ◽  
Vol 9 (2) ◽  
pp. 34-39 ◽  
Author(s):  
Chul-Hee Ahn ◽  
Hyoung-Hoon Kim ◽  
Sang-Hu Park ◽  
Chang-Min Son ◽  
Jeung-Sang Go
Keyword(s):  
Thin Film ◽  
Performance Evaluation ◽  
Temperature Sensor ◽  
Glass Surface ◽  
Sensor Array ◽  
Curved Glass ◽  
And Performance

scholarly journals Multifunctional Textile Platform for Fiber Optic Wearable Temperature-Monitoring Application

Micromachines ◽  
2019 ◽  
Vol 10 (12) ◽  
pp. 866 ◽  
Author(s):  
Ziyang Xiang ◽  
Liuwei Wan ◽  
Zidan Gong ◽  
Zhuxin Zhou ◽  
Zhengyi Ma ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Temperature Sensor ◽  
High Sensitivity ◽  
Wavelength Shift ◽  
Heat Sources ◽  
Time Dynamic ◽  
Textile Sensor ◽  
Fbg Sensors ◽  
Comfort Parameters ◽  
Monitoring Application

Wearable sensing technologies have been developed rapidly in the last decades for physiological and biomechanical signal monitoring. Much attention has been paid to functions of wearable applications, but comfort parameters have been overlooked. This research presents a developed fabric temperature sensor by adopting fiber Bragg grating (FBG) sensors and processing via a textile platform. This FBG-based quasi-distributed sensing system demonstrated a sensitivity of 10.61 ± 0.08 pm/°C with high stability in various temperature environments. No obvious wavelength shift occurred under the curvatures varying from 0 to 50.48 m−1 and in different integration methods with textiles. The temperature distribution monitored by the developed textile sensor in a complex environment with multiple heat sources was deduced using MATLAB to present a real-time dynamic temperature distribution in the wearing environment. This novel fabric temperature sensor shows high sensitivity, stability, and usability with comfort textile properties that are of great potential in wearable applications.

scholarly journals Reconstruction of Temperature Distribution in a Steel Block Using an Ultrasonic Sensor Array

2014 ◽  
Vol 33 (3) ◽  
pp. 458-470 ◽  
Author(s):  
A. Gajdacsi ◽  
A. J. C. Jarvis ◽  
P. Huthwaite ◽  
F. B. Cegla
Keyword(s):  
Temperature Distribution ◽  
Sensor Array ◽  
Ultrasonic Sensor
Sign in / Sign up

Export Citation Format

Share Document