scholarly journals Computation of individual errors from a single flank gear-meshing test. (3rd Report, Lead error of spur gear).

1989 ◽  
Vol 55 (515) ◽  
pp. 1708-1713
Author(s):  
Hiroshige FUJIO ◽  
Ryouhei TAKADA ◽  
Naoki WATANABE
Keyword(s):  
Spur Gear ◽  
Lead Error

Simulating Army-Relevant Spur Gear Contacts with a Ball-on-Disc Tribometer

2015 ◽  
Author(s):  
Mark R. Riggs ◽  
Stephen P. Berkebile ◽  
Adrian A. Hood ◽  
Brian D. Dykas
Keyword(s):  
Spur Gear ◽  
Ball On Disc

Effect of Contact Ratio on Spur Gear Dynamic Load With No Tooth Profile Modifications

1996 ◽  
Vol 118 (3) ◽  
pp. 439-443 ◽  
Author(s):  
Chuen-Huei Liou ◽  
Hsiang Hsi Lin ◽  
F. B. Oswald ◽  
D. P. Townsend
Keyword(s):  
Dynamic Load ◽  
Spur Gear ◽  
Tooth Size ◽  
Contact Ratio ◽  
Gear Dynamics ◽  
Wide Range ◽  
Gear Contact ◽  
Center Distance ◽  
Selection Of ◽  
Better Than

This paper presents a computer simulation showing how the gear contact ratio affects the dynamic load on a spur gear transmission. The contact ratio can be affected by the tooth addendum, the pressure angle, the tooth size (diametral pitch), and the center distance. The analysis presented in this paper was performed by using the NASA gear dynamics code DANST. In the analysis, the contact ratio was varied over the range 1.20 to 2.40 by changing the length of the tooth addendum. In order to simplify the analysis, other parameters related to contact ratio were held constant. The contact ratio was found to have a significant influence on gear dynamics. Over a wide range of operating speeds, a contact ratio close to 2.0 minimized dynamic load. For low-contact-ratio gears (contact ratio less than two), increasing the contact ratio reduced gear dynamic load. For high-contact-ratio gears (contact ratio equal to or greater than 2.0), the selection of contact ratio should take into consideration the intended operating speeds. In general, high-contact-ratio gears minimized dynamic load better than low-contact-ratio gears.

Effect of design parameters on stresses occurring at the tooth root in a spur gear pressed on a shaft

2021 ◽  
pp. 095440892199529
Author(s):  
Fatih Güven
Keyword(s):  
Internal Pressure ◽  
Tangential Stress ◽  
Spur Gear ◽  
Design Parameters ◽  
Interference Fit ◽  
Gear Design ◽  
Compact Design ◽  
Fit Tolerance ◽  
Moderate Stress ◽  
Good Agreement

Gears are commonly used in transmission systems to adjust velocity and torque. An integral gear or an interference fit could be used in a gearbox. Integral gears are mostly preferred as driving gear for a compact design to reduce the weight of the system. Interference fit makes the replacement of damaged gear possible and re-use of the shaft compared to the integral shaft. However, internal pressure occurs between mating surfaces of the components mated. This internal pressure affects the stress distribution at the root and bottom land of the gear. In this case, gear parameters should be re-considered to assure gear life while reducing the size of the gear. In this study, interference fitted gear-shaft assembly was examined numerically. The effects of rim thickness, profile shifting, module and fit tolerance on bending stress occurring at the root of the gear were investigated to optimize gear design parameters. Finite element models were in good agreement with analytical solutions. Results showed that the rim thickness of the gear is the main parameter in terms of tangential stress occurring at the bottom land of the gear. Positive profile shifting reduces the tangential stress while the pitch diameter of the gear remains constant. Also, lower tolerance class could be selected to moderate stress for small rim thickness.

Modeling of surface roughness in a novel magnetorheological gear profile finishing process

2020 ◽  
pp. 095440622097826
Author(s):  
Ravi Datt Yadav ◽  
Anant Kumar Singh ◽  
Kunal Arora
Keyword(s):  
Surface Roughness ◽  
Gear Tooth ◽  
Surface Characteristics ◽  
Spur Gear ◽  
Tooth Profile ◽  
Tooth Surface ◽  
Magnetic Flux Density ◽  
Element Analysis ◽  
Finishing Process ◽  
Gear Profile

Fine finishing of spur gears reduces the vibrations and noise and upsurges the service life of two mating gears. A new magnetorheological gear profile finishing (MRGPF) process is utilized for the fine finishing of spur gear teeth profile surfaces. In the present study, the development of a theoretical mathematical model for the prediction of change in surface roughness during the MRGPF process is done. The present MRGPF is a controllable process with the magnitude of the magnetic field, therefore, the effect of magnetic flux density (MFD) on the gear tooth profile has been analyzed using an analytical approach. Theoretically calculated MFD is validated experimentally and with the finite element analysis. To understand the finishing process mechanism, the different forces acting on the gear surface has been investigated. For the validation of the present roughness model, three sets of finishing cycle experimentations have been performed on the spur gear profile by the MRGPF process. The surface roughness of the spur gear tooth surface after experimentation was measured using Mitutoyo SJ-400 surftest and is equated with the values of theoretically calculated surface roughness. The results show the close agreement which ranges from −7.69% to 2.85% for the same number of finishing cycles. To study the surface characteristics of the finished spur gear tooth profile surface, scanning electron microscopy is used. The present developed theoretical model for surface roughness during the MRGPF process predicts the finishing performance with cycle time, improvement in the surface quality, and functional application of the gears.

Sign in / Sign up

Export Citation Format

Share Document