scholarly journals Effect of Detachment and Attachment of Top Foil on Predicted Maximum Load Carrying Capacity of Bump Foil Journal Bearings(Part 2: Extensive Survey of Bearing Design Variables)

2011 ◽  
Vol 77 (777) ◽  
pp. 1866-1878
Author(s):  
Kiyoshi HATAKENAKA ◽  
Daiki MICHITA ◽  
Hiroto HASHIMOTO
Robotica ◽  
2009 ◽  
Vol 27 (1) ◽  
pp. 147-159 ◽  
Author(s):  
M. H. Korayem ◽  
A. Nikoobin ◽  
V. Azimirad

SUMMARYIn this paper, finding the maximum load carrying capacity of mobile manipulators for a given two-end-point task is formulated as an optimal control problem. The solution methods of this problem are broadly classified as indirect and direct. This work is based on the indirect solution which solves the optimization problem explicitly. In fixed-base manipulators, the maximum allowable load is limited mainly by their joint actuator capacity constraints. But when the manipulators are mounted on the mobile bases, the redundancy resolution and nonholonomic constraints are added to the problem. The concept of holonomic and nonholonomic constraints is described, and the extended Jacobian matrix and additional kinematic constraints are used to solve the extra DOFs of the system. Using the Pontryagin's minimum principle, optimality conditions for carrying the maximum payload in point-to-point motion are obtained which leads to the bang-bang control. There are some difficulties in satisfying the obtained optimality conditions, so an approach is presented to improve the formulation which leads to the two-point boundary value problem (TPBVP) solvable with available commands in different softwares. Then, an algorithm is developed to find the maximum payload and corresponding optimal path on the basis of the solution of TPBVP. One advantage of the proposed method is obtaining the maximum payload trajectory for every considered objective function. It means that other objectives can be achieved in addition to maximize the payload. For the sake of comparison with previous results in the literature, simulation tests are performed for a two-link wheeled mobile manipulator. The reasonable agreement is observed between the results, and the superiority of the method is illustrated. Then, simulations are performed for a PUMA arm mounted on a linear tracked base and the results are discussed. Finally, the effect of final time on the maximum payload is investigated, and it is shown that the approach presented is also able to solve the time-optimal control problem successfully.


Author(s):  
D.-J. Shim ◽  
G. M. Wilkowski ◽  
D. L. Rudland ◽  
F. W. Brust ◽  
Kazuo Ogawa

Section XI of the ASME Code allows the users to conduct flaw evaluation analyses by using limit-load equations with a simple correction factor to account elastic-plastic fracture conditions. This correction factor is called a Z-factor, and is simply the ratio of the limit-load to elastic-plastic fracture mechanics (EPFM) maximum-load predictions for a flaw in a pipe. The past ASME Section XI Z-factors were based on a circumferential through-wall crack in a pipe rather than a surface crack. Past analyses and pipe tests with circumferential through-wall cracks in monolithic welds showed that the simplified EPFM analyses (called J-estimation schemes) could give good predictions by using the toughness, i.e., J-R curve, of the weld metal and the strength of the base metal. The determination of the Z-factor for a dissimilar metal weld (DMW) is more complicated because of the different strength base metals on either side of the weld. This strength difference can affect the maximum load-carrying capacity of the flawed pipe by more than the weld toughness. Recent work by the authors for circumferential through-wall cracks in DMWs has shown that an equivalent stress-strain curve is needed in order for the typical J-estimation schemes to correctly predict the load carrying capacity in a cracked DMW. In this paper, the Z-factors for circumferential surface cracks in DMW were determined. For this purpose, a material property correction factor was determined by comparing the crack driving force calculated from the J-estimation schemes to detailed finite element (FE) analyses. The effect of crack size and pipe geometry on the material correction factor was investigated. Using the determined crack-driving force and the appropriate toughness of the weld metal, the Z-factors were calculated for various crack sizes and pipe geometries. In these calculations, a ‘reference’ limit-load was determined by using the lower strength base metal flow stress. Furthermore, the effect of J-R curve on the Z-factor was investigated. Finally, the Z-factors developed in the present work were compared to those developed earlier for through-wall cracks in DMWs.


1988 ◽  
Vol 32 (01) ◽  
pp. 37-43
Author(s):  
Paul C. Xirouchakis

The solution is presented for an infinite elastic-softening floating beam under a point load. The response depends on two nondimensional parameters: the negative stiffness coefficient that characterizes the descending part of the moment-curvature curve, and the nondimensional softening region half-length. The solution exhibits two important features that the elastic-perfectly plastic solution does not show. First, in certain ranges of parameters, the elastic-softening beam has a clearly defined maximum load carrying capacity. Second, in some other ranges of parameters, the elastic-softening beam has a minimum load or residual strength. The beam stiffens up upon further deformation due to the reactions of the water foundation. Critical softening parameters are calculated that separate stable from unstable behavior.


2019 ◽  
Vol 16 (1) ◽  
Author(s):  
Yago Carvalho Lima ◽  
Mirian Ayumi Kurauti ◽  
Gabriel da Fonseca Alves ◽  
Jonathan Ferezini ◽  
Silvano Piovan ◽  
...  

Abstract Background A combination of resistance training and whey protein supplementation is a common practice among athletes and recreational exercisers to enhance muscle growth and strength. Although their safety as food additives is controversial, artificial sweeteners are present in whey protein supplements. Thus, natural sweeteners extracted from the leaves of Stevia rebaudiana are a potential alternative, due to their safety and health benefits. Here, we investigated the effects of whey protein sweetened with S. rebaudiana on physical performance and mitochondrial biogenesis markers in the skeletal muscle of resistance-trained rats. Methods Forty male Wistar rats were distributed into four groups: sedentary rats, trained rats, trained rats receiving whey protein and trained rats receiving whey protein sweetened with S. rebaudiana leaf extracts. Resistance training was performed by climbing a ladder 5 days per week, during 8-weeks. The training sessions consisted of four climbs carrying a load of 50, 75, 90, and 100% of the maximum load-carrying capacity which we determined before by performing a maximum load-carrying test for each animal. After this period, we collected plasma and tissues samples to evaluate biochemical, histological and molecular (western blot) parameters in these rats. Results Dietary supplementation with whey protein sweetened with S. rebaudiana significantly enhanced the maximum load-carrying capacity of resistance-trained rats, compared with non-sweetened whey protein supplementation. This enhanced physical performance was accompanied by an increase in the weight of the gastrocnemius and soleus muscle pads. Although the muscle pad of the biceps brachii was not altered, we observed a significant increase in PGC-1α expression, which was followed by a similar pattern in TFAM protein expression, two important mitochondrial biogenesis markers. In addition, a higher level of AMPK phosphorylation was observed in these resistance-trained rats. Finally, supplementation with whey protein sweetened with S. rebaudiana also induced a significant decrease in retroperitoneal adipocyte diameter and an increase in the weight of brown adipose tissue pads in resistance-trained rats. Conclusion The addition of Stevia rebaudiana leaf extracts to whey protein appears to be a potential strategy for those who want to increase muscular mass and strength and also improve mitochondrial function. This strategy may be useful for both athletes and patients with metabolic disorders, such as obesity and type 2 diabetes.


1970 ◽  
Vol 12 (2) ◽  
pp. 123-129 ◽  
Author(s):  
B. C. Majumdar

A theoretical investigation is made to predict the performance of an externally pressurized air journal bearing having several pressure sources. The pressure distribution, which leads to the determination of load-carrying capacity and flow requirement, is obtained by solving Reynolds equation numerically. The load and flow, expressed in non-dimensional parameters, are presented for different bearing design parameters (dimensionless). The results predicted by this method are compared with others' experimental data.


Sign in / Sign up

Export Citation Format

Share Document