scholarly journals Construction and Calculation of Reinforced Concrete Overlap with A High Spatial Work Effect

2018 ◽  
Vol 7 (3.2) ◽  
pp. 567
Author(s):  
Taliat Azizov ◽  
Anna Azizova ◽  
Sakr Al Ghadban
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Normal Torsion ◽  
Work Effect ◽  
Analogous Effect

The article proposes the construction of a prefabricated monolithic reinforced concrete overlap consisting of beams hollow triangular section. It is shown that in such overlap the effect of spatial work is much higher than the analogous effect in traditional overlap that consists of U-shaped or T-beams and slabs. The technique of determining the forces of interaction of individual beams in the composition of the overlap is given. The technique is based on a discrete-continual method developed by the author, which is adapted to the calculation of overlaps that consist of considered beams. The technique of determining the effort between the shelf and the ribs of a beam during its bending is presented. It is based on the theory of compound rods. The algorithm of calculation taking into account the spatial work is presented as well as the principles of constructing overlaps consisting of beams hollow triangular section, taking into account the change in their rigidity as a result of cracks formation. An approach to the determination of the rigidity of beams with normal torsion fractures is given, based on the approximation of numerical experimental data.  

Improvement Of Curvilinear Diagrams Of Concrete Deformation

2019 ◽  
pp. 99-104
Keyword(s):  
Reinforced Concrete ◽  
Peak Load ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Deformation Model ◽  
Reinforced Concrete Structures ◽  
Significant Difference ◽  
Deformation Diagrams

Problems when calculating reinforced concrete structures based on the concrete deformation under compression diagram, which is presented both in Russian and foreign regulatory documents on the design of concrete and reinforced concrete structures are considered. The correctness of their compliance for all classes of concrete remains very approximate, especially a significant difference occurs when using Euronorm due to the different shape and sizes of the samples. At present, there are no methodical recommendations for determining the ultimate relative deformations of concrete under axial compression and the construction of curvilinear deformation diagrams, which leads to limited experimental data and, as a result, does not make it possible to enter more detailed ultimate strain values into domestic standards. The results of experimental studies to determine the ultimate relative deformations of concrete under compression for different classes of concrete, which allowed to make analytical dependences for the evaluation of the ultimate relative deformations and description of curvilinear deformation diagrams, are presented. The article discusses various options for using the deformation model to assess the stress-strain state of the structure, it is concluded that it is necessary to use not only the finite values of the ultimate deformations, but also their intermediate values. This requires reliable diagrams "s–e” for all classes of concrete. The difficulties of measuring deformations in concrete subjected to peak load, corresponding to the prismatic strength, as well as main cracks that appeared under conditions of long-term step loading are highlighted. Variants of more accurate measurements are proposed. Development and implementation of the new standard GOST "Concretes. Methods for determination of complete diagrams" on the basis of the developed method for obtaining complete diagrams of concrete deformation under compression for the evaluation of ultimate deformability of concrete under compression are necessary.

EXPERIMENTAL STUDIES OF REINFORCED CONCRETE STRUCTURES WITH CROSS-SHAPED SPATIAL CRACK UNDER TORSION WITH BENDING

2020 ◽  
Vol 92 (6) ◽  
pp. 13-25
Author(s):  
Vl.I. KOLCHUNOV ◽  
◽  
A.I. DEMYANOV ◽  
M.M. MIHAILOV ◽  
◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Experimental Determination ◽  
Calculation Method ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Design Parameters ◽  
Reinforced Concrete Structures ◽  
Experimental Scheme

The article offers a method and program for experimental studies of reinforced concrete structures with cross-shaped spatial crack under torsion with bending, the main purpose of which is to check the design assumptions and experimental determination of the design parameters of the proposed calculation method. The conducted experimental studies provide an opportunity to test the proposed calculation apparatus and clarify the regularities for determining deflections, angles of rotation of extreme sections, and stresses in the compressed zone of concrete. For analysis, the article presents a typical experimental scheme for the formation and development of cracks in the form of a sweep, as well as characteristic graphs of the dependence of the angles of rotation of end sections.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

Equilibrium Sorptions in Heterogeneous Ion Exchange Membranes

1992 ◽  
Vol 57 (9) ◽  
pp. 1905-1914
Author(s):  
Miroslav Bleha ◽  
Věra Šumberová
Keyword(s):  
Experimental Data ◽  
Ion Exchange ◽  
Total Content ◽  
Distribution Coefficients ◽  
Exchange Capacity ◽  
Ion Exchange Membranes ◽  
Ion Exchange Capacity ◽  
Equilibrium Sorption ◽  
Inhomogeneity Factor

The equilibrium sorption of uni-univalent electrolytes (NaCl, KCl) in heterogeneous cation exchange membranes with various contents of the ion exchange component and in ion exchange membranes Ralex was investigated. Using experimental data which express the concentration dependence of equilibrium sorption, validity of the Donnan relation for the systems under investigation was tested and values of the Glueckauf inhomogeneity factor for Ralex membranes were determined. Determination of the equilibrium sorption allows the effect of the total content of internal water and of the ion-exchange capacity on the distribution coefficients of the electrolyte to be determined.

On-Site Determination of the Polarization Resistance in a Reinforced Concrete Beam

CORROSION ◽  
1988 ◽  
Vol 44 (10) ◽  
pp. 761-765 ◽  
Author(s):  
S. Feliu ◽  
J. A. Gonzalez ◽  
C. Andrade ◽  
V. Feliu
Keyword(s):  
Reinforced Concrete ◽  
Polarization Resistance ◽  
Concrete Beam ◽  
Reinforced Concrete Beam
Sign in / Sign up

Export Citation Format

Share Document