scholarly journals Numerical Investigation on Effect of Rounded Cutting-Edge Radius and Machining Parameters in End Milling of AISI H13 Tool Steel

2018 ◽  
Vol 7 (4.30) ◽  
pp. 53
Author(s):  
Husni Nazra Abu Bakar ◽  
Jaharah A. Ghani ◽  
Che Hassan Che Haron
Keyword(s):  
Feed Rate ◽  
Cutting Tool ◽  
End Milling ◽  
Cutting Temperature ◽  
Cutting Edge ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Cutting Edge Radius ◽  
Edge Radius ◽  
Aisi H13

Rounded cutting-edge radius is commonly applied to finish and semi-finish cutting, precision machining and micro-machining. The optimum effect is closely related to the work and tool material as well as machining parameters. However, for numerous cutting process, the optimal radius of rounded cutting-edge radius and machining parameters applied in the AISI H13 of end-milling is yet unknown Therefore, in improving tool life and cutting tool performance, a suitable design of cutting edge geometry regarding cutting edge-radius and machining parameters need to be examined and properly selected. In this regard, the paper deals to examine the effect of cutting edge-radius in rounded form and machining parameters of cutting force, cutting temperature and chip formation through the end-milling process of AISI H13 using uncoated cemented carbide cutting tool through finite element simulation of Thirdwave AdvantEdge 7.2 software. The machining parameters applied in the simulation setup were 200 and 240m/min of cutting speed, 0.03 and 0.06mm/tooth of feed-rate and axial depth of cut of 0.1 and 0.2mm while width of cut in radial direction was kept constant at 6.0mm. The cutting geometries includes the cutting-edge radius of 0.03 and 0.05mm and 10° of rake angle. The obtained results revealed that cutting forces and cutting temperature is increase as depth of cut in axial direction and cutting-edge radius increases while increasing value of speed and feed-rate of cutting resulted in decreasing cutting forces but increasing cutting temperature. The maximum cutting temperature is 674.91℃. The value obtained is lesser than the AISI H13 austenitizing temperature, therefore a layer known as white layer is supposedly hard to be created based on the cutting geometry and machining parameters applied.  

Study on micro cutting fundamentals considering the cutting edge radius and the workpiece material in micro end milling

2020 ◽  
pp. 095440892094602
Author(s):  
Yang Li ◽  
Xiang Cheng ◽  
Siying Ling ◽  
Guangming Zheng ◽  
Huanbao Liu ◽  
...  
Keyword(s):  
End Milling ◽  
Chip Thickness ◽  
Chip Morphology ◽  
Cutting Edge ◽  
Depth Of Cut ◽  
Workpiece Material ◽  
Micro Cutting ◽  
Cutting Edge Radius ◽  
Edge Radius ◽  
Micro End Milling

Previous studies found that the peripheral cutting edge and end cutting edge in micro end milling had different cutting phenomena considering the size effect in micro cutting processes. This paper is a further study on this point considering different workpiece materials and cutting edge radii. Finite element simulations have been conducted to determine the minimum undeformed chip thickness (MUCT) by the chip morphology and the results are verified by micromilling experiments. Both the simulations and experiments show that the MUCT of the peripheral cutting edge and the end cutting edge are different even if the cutting edge radii remain unchanged. The MUCT is directly proportional to the cutting edge radius. Material properties also have some effects on the MUCT of the peripheral cutting edge. But it has limited effects on that of the end cutting edge. The results indicate that the feed engagement other than the axial depth of cut should be carefully selected in micro end milling when considering different workpiece materials.

Micro Flat End Milling Simulation Model With Instantaneous Plowing Area Prediction

2016 ◽  
Vol 4 (2) ◽  
Author(s):  
Abdolreza Bayesteh ◽  
Junghyuk Ko ◽  
Martin Byung-Guk Jun
Keyword(s):  
Feed Rate ◽  
Tool Path ◽  
End Milling ◽  
Chip Thickness ◽  
Depth Of Cut ◽  
Uncut Chip Thickness ◽  
Chip Area ◽  
Edge Radius ◽  
Wide Range ◽  
Radial Depth

There is an increasing demand for product miniaturization and parts with features as low as few microns. Micromilling is one of the promising methods to fabricate miniature parts in a wide range of sectors including biomedical, electronic, and aerospace. Due to the large edge radius relative to uncut chip thickness, plowing is a dominant cutting mechanism in micromilling for low feed rates and has adverse effects on the surface quality, and thus, for a given tool path, it is important to be able to predict the amount of plowing. This paper presents a new method to calculate plowing volume for a given tool path in micromilling. For an incremental feed rate movement of a micro end mill along a given tool path, the uncut chip thickness at a given feed rate is determined, and based on the minimum chip thickness value compared to the uncut chip thickness, the areas of plowing and shearing are calculated. The workpiece is represented by a dual-Dexel model, and the simulation properties are initialized with real cutting parameters. During real-time simulation, the plowed volume is calculated using the algorithm developed. The simulated chip area results are qualitatively compared with measured resultant forces for verification of the model and using the model, effects of cutting conditions such as feed rate, edge radius, and radial depth of cut on the amount of shearing and plowing are investigated.

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

Numerical Investigation on Effect of Rounded Cutting Edge Radius in Milling of Ultra-High-Strength Steel 30Cr3SiNiMoVA

2013 ◽  
Vol 797 ◽  
pp. 202-207
Author(s):  
Chang Ying Wang ◽  
Jia Jin Tian ◽  
Qing Long An ◽  
Ming Chen
Keyword(s):  
Cutting Forces ◽  
High Strength Steel ◽  
High Strength ◽  
Cutting Edge ◽  
Depth Of Cut ◽  
Critical Depth ◽  
Cutting Edge Radius ◽  
Edge Radius ◽  
Ultra High Strength Steel ◽  
Critical Depth Of Cut

Ultra-high-strength steel 30Cr3SiNiMoVA (30Cr3) which has excellent mechanical properties is usually used to manufacture the key parts in aviation industry. Precision hard milling is an efficiency way to machine 30Cr3 instead of grinding. Rounded cutting edge radius has important influence on the machining process due to small depth of cut. In order to better understanding the influence of rounded cutting edge radius, cutting forces, cutting temperature, critical depth of cut, etc., is analyzed by using finite element method (FEM). The results show that cutting forces in theydirection are more sensitively to the rounded cutting edge radii. Ploughing effect is also observed at the end of the climb milling process and it has significant influence on the quality of the machined surface. Simulation reveals that the increment of rounded cutting edge radius can lead to the increment of critical depth of cut correspondingly and the proportionality factor is about 14%.

Edge Design for Regrinding Cutting Tool

2011 ◽  
Vol 101-102 ◽  
pp. 938-941
Author(s):  
Xin Li Tian ◽  
Hao Wang ◽  
Xiu Jian Tang ◽  
Zhao Li ◽  
Ai Bing Yu
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Edge ◽  
Edge Angle ◽  
Edge Radius ◽  
Tool Edge ◽  
Edge Defects ◽  
Tool Cutting ◽  
Edge Preparation

Regrinding of wasted cutting tools can recycle resources and decrease manufacturing costs. Influence of relative tool sharpness and tool cutting edge angle on tool edge radius were analyzed. Cutting force and cutting temperature were simulated with FEM on different edge radius. Edge preparation experiments were carried out though an abrasive nylon brushing method. The results show that RTS and cutting edge angle have influence on edge radius. Small edge radius might result in small cutting forces and lower average temperatures, could maintain the cutting state between tool and workpiece. The cutting edge defects can be eliminated through edge preparation, and a smooth cutting edge can be obtained. Cutting tool life will be improved through proper edge design and edge preparation.

Monitoring of Surface Roughness Based on Cutting Force and Cutting Temperature in Ball-End Milling Process by Utilizing Response Surface Analysis

2015 ◽  
Vol 799-800 ◽  
pp. 324-328
Author(s):  
Panrawee Yaisuk ◽  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Response Surface ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Temperature ◽  
Milling Process ◽  
Depth Of Cut ◽  
Tool Diameter ◽  
End Milling Process

The surface roughness is monitored using the cutting force and the cutting temperature in the ball-end milling process by utilizing the response surface analysis with the Box-Behnken design. The optimum cutting condition is obtained referring to the minimum surface roughness, which is the spindle speed, the feed rate, the depth of cut, and the tool diameter. The models of cutting force ratio and the cutting temperature are proposed and developed based on the experimental results. It is understood that the surface roughness is improved with an increase in spindle speed, feed rate and depth of cut. The cutting temperature decreases with an increase in tool diameter. The model verification has showed that the experimentally obtained surface roughness model is reliable and accurate to estimate the surface roughness.

Linear Sawing Apparatus and its Evaluation for Research Into High Speed Bone Sawing

2011 ◽  
Author(s):  
John J. Pearlman ◽  
Anil Saigal ◽  
Thomas P. James
Keyword(s):  
High Speed ◽  
Metal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Edge ◽  
Material Behavior ◽  
Depth Of Cut ◽  
Cutting Edge Radius ◽  
Edge Radius ◽  
Saw Blade

Previous research into the cutting mechanics of bone sawing has been primarily approached from the perspective of orthogonal metal machining with a single edge cutting tool. This was a natural progression from the larger body of knowledge on the mechanics of metal cutting. However, there are significant differences between typical orthogonal metal cutting parameters and those encountered in bone sawing, such as anisotropic material behavior, depth of cut on the order of cutting edge radius, chip formation mechanism in the context of a saw blade kerf, non-orthogonal considerations of set saw blade teeth, and cutting speed to name a few. In the present study, an attempt is made to overcome these shortcomings by employing a unique sawing fixture, developed to establish cutting speeds equivalent to those of typical sagittal saws used in orthopaedic procedures. The apparatus was developed for research into bone sawing mechanics and is not intended to be a commercial sawing machine. The sawing fixture incorporates the cutting speed possible with lathe operations, as well as the linear cutting capabilities of a milling machine. Depths of cut are on the same order of magnitude as the cutting edge radius typical to saw blade teeth. Initial measurements of cutting and thrust force, obtained with this new experimental equipment, are compared to previous work.

scholarly journals Analyzing the Effect of Machining Parameters Setting to the Surface Roughness during End Milling of CFRP-Aluminium Composite Laminates

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
M. Nurhaniza ◽  
M. K. A. M. Ariffin ◽  
F. Mustapha ◽  
B. T. H. T. Baharudin
Keyword(s):  
Surface Quality ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Optimal Cutting Parameters ◽  
Cnc End Milling

The quality of the machining is measured from surface finished and it is considered as the most important aspect in composite machining. An appropriate and optimum machining parameters setting is crucial during machining operation in order to enhance the surface quality. The objective of this research is to analyze the effect of machining parameters on the surface quality of CFRP-Aluminium in CNC end milling operation with PCD tool. The milling parameters evaluated are spindle speed, feed rate, and depth of cut. The L9 Taguchi orthogonal arrays, signal-to-noise (S/N) ratio, and analysis of variance (ANOVA) are employed to analyze the effect of these cutting parameters. The analysis of the results indicates that the optimal cutting parameters combination for good surface finish is high cutting speed, low feed rate, and low depth of cut.

Optimization of Machining Parameters for CNC Turning of Different Materials

2014 ◽  
Vol 592-594 ◽  
pp. 605-609
Author(s):  
Surendra Kumar Saini ◽  
Sharad Kumar Pradhan
Keyword(s):  
Feed Rate ◽  
316L Stainless Steel ◽  
Cutting Tool ◽  
Fractional Factorial Design ◽  
Spindle Speed ◽  
Fractional Factorial ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Turning Process ◽  
Cnc Turning

Abstract. This paper proposes an experimental investigation of the most influencing machining parameters like spindle speed, feed rate and depth of cut on CNC turning of three metals viz. 316L Stainless steel, EN24 alloy steel and Ti 6 Al 4V alloy. Fractional factorial design with orthogonal array [L9 (33)] is employed for the optimization of these turning process parameters. All experiments were carried out using EMCO CNC 250 Turn machine with carbide cutting tool. The comparison revealed that feed rate and depth of cut are the most significant turning factors on surface roughness followed by spindle speed for these three metals.

Influences of Cutting Edge Radius on Cutting Deformation in High-Speed Machining Ti6Al4V

2011 ◽  
Vol 305 ◽  
pp. 47-52
Author(s):  
Shu Cai Yang ◽  
Min Li Zheng ◽  
Yi Hang Fan ◽  
De Qiang Zhang ◽  
Ying Bin Li
Keyword(s):  
High Speed ◽  
Equivalent Stress ◽  
Cutting Temperature ◽  
Chip Thickness ◽  
Cutting Edge ◽  
High Speed Machining ◽  
Cutting Edge Radius ◽  
Edge Radius ◽  
Cutting Deformation ◽  
Deformation Coefficient

In order to obtain the influences of cutting edge radius on cutting deformation in high-speed machining Ti6Al4V, cutting temperature, equivalent stress distribution, the chip morphology and cutting deformation coefficient were analyzed in this paper. The results indicated that cutting edge changed the plastic flow of materials around tool tip and the actual tool rake angle, the tool-workpiece and tool-chip contact in cutting process which causes a greater impact on physical and mechanical performance in the given cutting conditions. When the cutting edge radius reached to 0.04mm,the cutting temperature and the equivalent stress existed mutations, which causes the mutation of chips. There was a chip thinning effect with the increase of the cutting edge radius. As the cutting edge radius increased, chip thickness and shear angle decreased, cutting deformation coefficient increased.

Sign in / Sign up

Export Citation Format

Share Document