SEISMIC BEHAVIOR OF POST-TENSIONED ROCKING COLUMNS WITH RE-PLACEABLE ENERGY DISSIPATERS

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
H. H. Hung ◽  
C. W. Huang ◽  
C. R. Jiang
Keyword(s):  
Energy Dissipation ◽  
Inelastic Deformation ◽  
Recovery Time ◽  
Seismic Behavior ◽  
Seismic Events ◽  
External Energy ◽  
Mechanical Joint ◽  
Bridge Column ◽  
Energy Dissipation Devices ◽  
Post Tensioned

To mitigate the column damage during seismic events and to reduce the recovery time after a major earthquake, a post-tensioned bridge column with a rocking interface above the foundation and externally-installed energy dissipation devices was proposed. The energy dissipation devices were specially designed to serve as fuse elements that can be easily replaced after yielding. In addition, a mechanical joint that can rotate freely in all directions was incorporated at one end of the dissipater to ensure bending was not transmitted into this device. To verify the seismic performance of the proposed system, two proposed specimens with different prestressing forces and design details in the rocking base were constructed and tested. From the experiments, it was found that the proposed post-tensioned specimens suffered minor damage after cyclic loadings. All of the damage was concentrated on the inelastic deformation that occurred at the external energy dissipaters. The ease of replacement for the external energy dissipaters was also confirmed.

Comparison of the Results Obtained in Simulation of SERB Dampers Using Two Different Hysteresis Models

2018 ◽  
Vol 880 ◽  
pp. 353-358
Author(s):  
Adriana Ionescu ◽  
Mihai Negru ◽  
Cristian Oliviu Burada
Keyword(s):  
Theoretical Model ◽  
Energy Dissipation ◽  
Seismic Behavior ◽  
Seismic Energy ◽  
Theoretical Models ◽  
Modified Model ◽  
The Difference ◽  
Energy Dissipation Devices ◽  
Comparison Of The Results ◽  
Damping Systems

This paper presents the difference between the results obtained with GenEcAm in simulating the seismic behavior of a P + 10E building equipped with SERB dampers modeled with two hysteresis models, namely the classic Bouc-Wen model and a Bouc-Wen modified model Bouc-Wen_Exp, in order to highlight the most appropriate theoretical model for modeling these dampers. The GenEcAm program is created by the author for the dynamic analysis during seism for structures of buildings equipped with different earthquake damping systems, with the possibility to use 9 different theoretical models of hysteresis for simulating the hysterical behavior of seismic energy dissipation devices that fit the antiseismic system of the analysed building.

Low-Cycle Fatigue Performance of Buckling Restrained Braces and Assessment of Cumulative Damage under Severe Earthquakes

2018 ◽  
Vol 763 ◽  
pp. 867-874
Author(s):  
Yu Shu Liu ◽  
Ke Peng Chen ◽  
Guo Qiang Li ◽  
Fei Fei Sun
Keyword(s):  
Fatigue Life ◽  
Energy Dissipation ◽  
Structural Reliability ◽  
Low Cycle Fatigue ◽  
Engineering Application ◽  
Fatigue Performance ◽  
Cycle Fatigue ◽  
Variable Amplitude ◽  
Buckling Restrained Braces ◽  
Energy Dissipation Devices

Buckling Restrained Braces (BRBs) are effective energy dissipation devices. The key advantages of BRB are its comparable tensile and compressive behavior and stable energy dissipation capacity. In this paper, low-cycle fatigue performance of domestic BRBs is obtained based on collected experimental data under constant and variable amplitude loadings. The results show that the relationship between fatigue life and strain amplitude satisfies the Mason-Coffin equation. By adopting theory of structural reliability, this paper presents several allowable fatigue life curves with different confidential levels. Besides, Palmgren-Miner method was used for calculating BRB cumulative damages. An allowable damage factor with 95% confidential level is put forward for assessing damage under variable amplitude fatigue. In addition, this paper presents an empirical criterion with rain flow algorithm, which may be used to predict the fracture of BRBs under severe earthquakes and provide theory and method for their engineering application. Finally, the conclusions of the paper were vilified through precise yet conservative prediction of the fatigue failure of BRB.

A combined experimental and numerical analysis on the seismic behavior of short reinforced concrete columns with different structural sizes and axial compression ratios

2017 ◽  
Vol 27 (9) ◽  
pp. 1416-1447 ◽  
Author(s):  
Liu Jin ◽  
Shuai Zhang ◽  
Dong Li ◽  
Haibin Xu ◽  
Xiuli Du ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Axial Compression ◽  
Seismic Behavior ◽  
Load Capacity ◽  
Concrete Columns ◽  
Simulation Method ◽  
Reinforced Concrete Columns ◽  
Mesoscopic Simulation ◽  
Energy Dissipation Capacity

The results of an experimental program on eight short reinforced concrete columns having different structural sizes and axial compression ratios subjected to monotonic/cyclic lateral loading were reported. A 3D mesoscopic simulation method for the analysis of mechanical properties of reinforced concrete members was established, and then it was utilized as an important supplement and extension of the traditional experimental method. Lots of numerical trials, based on the restricted experimental results and the proposed 3D mesoscopic simulation method, were carried out to sufficiently evaluate the seismic performances of short reinforced concrete columns with different structural sizes and axial compression ratios. The test results indicate that (1) the failure pattern of reinforced concrete columns can be significantly affected by the shear-span ratio; (2) increasing the axial compression ratio could improve the load capacity of the reinforced concrete column, but the deformation capacity would be restricted and the failure mode would be more brittle, consequently the energy dissipation capacity could be deteriorated; and (3) the load capacity, the displacement ductility, and the energy dissipation capacity of the short reinforced concrete columns all exhibit clear size effect, namely, the size effect could significantly affect the seismic behavior of reinforced concrete columns.

Research on the Joint of Concrete-Filled Steel Tubular Column and Steel Beam

2013 ◽  
Vol 351-352 ◽  
pp. 174-178
Author(s):  
Ying Zi Yin ◽  
Yan Zhang
Keyword(s):  
Energy Dissipation ◽  
Failure Mechanism ◽  
Compression Ratio ◽  
Seismic Behavior ◽  
Strength Degradation ◽  
Steel Beam ◽  
Failure Characteristics ◽  
Static Test ◽  
Axial Compression Ratio ◽  
Energy Dissipation Capacity

With the pseudo-static test of 4 concrete-filled square steel tubular column and steel beam joint with outer stiffened ring, this paper discusses the failure characteristics, failure mechanism and seismic behavior of joints under different axial compression ratio. The analysis of the testing results shows: when reached the ultimate strength, the strength degradation and stiffness degradation of joints are slowly and the ductility is also good, the energy dissipation capacity of joints is much better.

scholarly journals Development Behavior for Post-Tensioned Self-Centering Steel Connection under Cyclic Loading

2017 ◽  
Vol 3 (3) ◽  
pp. 152-159
Author(s):  
Ahmadreza Torabipour ◽  
M. R. Shiravand
Keyword(s):  
Energy Dissipation ◽  
Numerical Models ◽  
Perfect Match ◽  
High Strength ◽  
Relative Displacement ◽  
Initial Stiffness ◽  
Validation Parameters ◽  
Steel Connection ◽  
Energy Dissipation Capacity ◽  
Post Tensioned

One of the newest steel beam-column joints to replace conventional welded connections, post-tensioned connection steel is with the upper and lower angles. In this connection are high-strength steel strands that parallel beam web and angles between beams and column. Actually high resistance strands and upper and lower angles respectively are provider centralization properties and energy dissipation capacity of the connection. The benefits of post-tensioned steel can be used in connection with the centralization and lack of relative displacement (drift) persistent, stay elastic core components such as connecting beams, columns and fountains connection, appropriate initial stiffness and joint manufacture with materials and traditional skills. . In this study, numerical modelling in Abaqus software, the results of the analysis were compared with the results of laboratory samples and the results showed that the two together are a perfect match. After validation, parameters influential centrist connection then pulled the thick angles in three numerical models were evaluated.  The results show that by increasing the thickness of the angles, increase energy dissipation capacity and ductility connection and the β₁ value does not experience tangible changes with changes in angle thickness.

Sign in / Sign up

Export Citation Format

Share Document