A study on heating and cooling requirements for green buildings for refugee settlements

In this study a new multi-generation system which generates power (electricity), thermal energy (heating and cooling) and ash for agricultural needs has been developed and analysed. The system consists of a Biomass Integrated Gasification Combined Cycle (BIGCC) and an absorption chiller system. The system generates about 3.4 MW electricity, 4.9 MW of heat, 88 kW of cooling and 90 kg/h of ash. The multi-generation system has been modelled using Cycle Tempo and EES. Energy, exergy and exergoeconomic analysis of this system had been conducted and exergy costs have been calculated. The exergoeconomic study shows that gasifier, combustor, and Heat Recovery Steam Generator are the main components where the total cost rates are the highest. Exergoeconomic variables such as relative cost difference (r) and exergoeconomic factor (f) have also been calculated. Exergoeconomic factor of evaporator, combustor and condenser are 1.3%, 0.7% and 0.9%, respectively, which is considered very low, indicates that the capital cost rates are much lower than the exergy destruction cost rates. It implies that the improvement of these components could be achieved by increasing the capital investment. The exergy cost of electricity produced in the gas turbine and steam turbine is 0.1050 £/kWh and 0.1627 £/kWh, respectively. The cost of ash is 0.0031 £/kg. In some Asian countries, such as Indonesia, ash could be used as fertilizer for agriculture. Heat exergy cost is 0.0619 £/kWh for gasifier and 0.3972 £/kWh for condenser in the BIGCC system. In the AC system, the exergy cost of the heat in the condenser and absorber is about 0.2956 £/kWh and 0.5636 £/kWh, respectively. The exergy cost of cooling in the AC system is 0.4706 £/kWh. This study shows that exergoeconomic analysis is powerful tool for assessing the costs of products.

Download Full-text

Optimization of the time the chromatograph thermostats exit to a given temperature

Izmeritel`naya Tekhnika ◽

10.32446/0368-1025it.2020-6-40-45 ◽

2020 ◽

pp. 40-45

Author(s):

Nadezhda O. Vzduleva ◽

Valery B. Gitlin

Keyword(s):

Heating Rate ◽

Entire Range ◽

Gas Chromatograph ◽

Heating And Cooling ◽

Operating Temperatures ◽

The Stability

The problems of ensuring the stability of the temperature of the chromatographic experiment carried out using a serial gas chromatograph LGH-3000 are considered. Limiting the permissible heating rate of the chromatograph thermostats does not allow a quick transition to the new conditions of the chromatographic experiment in accordance with the requirements of the technical conditions. The processes of heating and cooling the thermostat are analyzed. It is shown that the ratio of the duration of the interval equal to the sum of the durations of the heating and cooling intervals to the duration of the heating interval is inversely proportional to the temperature of the chromatographic experiment. Based on this situation, an empirical algorithm is proposed for heating the thermostat to a given temperature, which made it possible to reduce the time it takes to reach a given temperature in the entire range of operating temperatures.

Download Full-text

INFLUENCE THE QUENCHING AND TEMPERING ON THE MICROSTRUCTURE, MECHANICAL PROPERTIES AND SURFACE ROUGHNESS, OF MEDIUM CARBON STEEL

THE IRAQI JOURNAL FOR MECHANICAL AND MATERIALS ENGINEERING ◽

10.32852/iqjfmme.vol18.iss1.78 ◽

2018 ◽

Vol 18 (1) ◽

pp. 125-135

Author(s):

Sattar H A Alfatlawi

Keyword(s):

Mechanical Properties ◽

Heat Treatment ◽

Surface Roughness ◽

Carbon Steel ◽

Cold Water ◽

Medium Carbon Steel ◽

Medium Carbon ◽

Heating And Cooling ◽

Treatment Processes ◽

Quenching And Tempering

One of ways to improve properties of materials without changing the product shape toobtain the desired engineering applications is heating and cooling under effect of controlledsequence of heat treatment. The main aim of this study was to investigate the effect ofheating and cooling on the surface roughness, microstructure and some selected propertiessuch as the hardness and impact strength of Medium Carbon Steel which treated at differenttypes of heat treatment processes. Heat treatment achieved in this work was respectively,heating, quenching and tempering. The specimens were heated to 850°C and left for 45minutes inside the furnace as a holding time at that temperature, then quenching process wasperformed in four types of quenching media (still air, cold water (2°C), oil and polymersolution), respectively. Thereafter, the samples were tempered at 200°C, 400°C, and 600°Cwith one hour as a soaking time for each temperature, then were all cooled by still air. Whenthe heat treatment process was completed, the surface roughness, hardness, impact strengthand microstructure tests were performed. The results showed a change and clearimprovement of surface roughness, mechanical properties and microstructure afterquenching was achieved, as well as the change that took place due to the increasingtoughness and ductility by reducing of brittleness of samples.

Download Full-text

Green Architecture and its applications in Hospitals:Analytical study of existing project to extract the mechanisms of applying green architecture in hospitals

Association of Arab Universities Journal of Engineering Sciences ◽

10.33261/jaaru.2020.27.2.009 ◽

2020 ◽

Vol 27 (2) ◽

pp. 81-93

Author(s):

Anfal Muayad Mayoof

Keyword(s):

Cultural Values ◽

Analytical Study ◽

Complex Function ◽

Green Building ◽

Green Buildings ◽

Social Aspects ◽

Local Climate ◽

Green Architecture ◽

Reduce Energy Consumption ◽

The One

Hospitals are the major contributor to environmental corruption and the biggest drain onenergy in their life cycle because they are complex, multifunctional giant facilities. Several recent studieshave been carried out to find the most suitable solutions to reduce energy consumption provide it on-siteand contribute to supporting economic, environmental and social aspects. The reason for the slowmovement of green buildings for hospitals is to focus on a suitable design for the complex function thatdeals with the local climate, natural resources, economy and cultural values and avoid the one-size-fits alldesign. This made the solutions used multiple and varied, different for greening of the hospital and put theresearch in the absence of a clear perception of the mechanisms of the application of green architecture inhospitals and this identified the problem of research. Therefore, the study looked at an analytical study ofexisting project models designed according to the strategies and standards of green architecture todetermine the strategies adopted in each project, and by adopting the analytical method after determiningthe strategy used in each building to achieve the green architecture and then comparing them according tothe standards adopted using the global LEED system Green Building Council. The results that will bereached are the mechanisms of applying Green Architecture to Hospitals.

Download Full-text