scholarly journals GNSS-Warp Software for Real-Time Precise Point Positioning

2015 ◽  
Vol 50 (2) ◽  
pp. 59-76 ◽  
Author(s):  
Hadaś Tomasz
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Static Mode ◽  
Time Service ◽  
The Real ◽  
North East ◽  
Satellite Geometry ◽  
Point Positioning ◽  
Performance Validation ◽  
Mode A

Abstract On April 1, 2013 IGS launched the real-time service providing products for Precise Point Positioning (PPP). The availability of real-time makes PPP a very powerful technique to process GNSS signals in real-time and opens a new PPP applications opportunities. There are still, however, some limitations of PPP, especially in the kinematic mode. A significant change in satellite geometry is required to efficiently de-correlate troposphere delay, receiver clock offset, and receiver height. In order to challenge PPP limitations, the GNSS-WARP (Wroclaw Algorithms for Real-time Positioning) software has been developed from scratch at Wroclaw University of Environmental and Life Science in Poland. This paper presents the GNSS-WARP software itself and some results of GNSS data analysis using PPP and PPP-RTK (Real-Time Kinematic) technique. The results of static and kinematic processing in GPS only and GPS + GLONASS mode with final and real-time products are presented. Software performance validation in postprocessing mode confirmed that the software can be considered as a state-ofthe- art software and used for further studies on PPP algorithm development. The real-time positioning test made it possible to assess the quality of real-time coordinates, which is a few millimeters for North, East, Up in static mode, a below decimeter in kinematic mode. The accuracy and precision of height estimates in kinematic mode were improved by constraining the solution with an external, near real-time troposphere model. The software also allows estimation of real-time ZTD, however, the obtained precision of 11.2 mm means that further improvements in the software, real-time products or processing strategy are required.

scholarly journals Performance Evaluation of Real-Time Precise Point Positioning with Both BDS-3 and BDS-2 Observations

Sensors ◽  
2020 ◽  
Vol 20 (21) ◽  
pp. 6027
Author(s):  
Lin Pan ◽  
Xuanping Li ◽  
Wenkun Yu ◽  
Wujiao Dai ◽  
Cuilin Kuang ◽  
...  
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Rapid Development ◽  
Satellite System ◽  
Convergence Time ◽  
Static Mode ◽  
The Real ◽  
Point Positioning ◽  
Time Critical

For time-critical precise applications, one popular technology is the real-time precise point positioning (PPP). In recent years, there has been a rapid development in the BeiDou Navigation Satellite System (BDS), and the constellation of global BDS (BDS-3) has been fully deployed. In addition to the regional BDS (BDS-2) constellation, the real-time stream CLK93 has started to support the BDS-3 constellation, indicating that the real-time PPP processing involving BDS-3 observations is feasible. In this study, the global positioning performance of real-time PPP with BDS-3/BDS-2 observations is initially evaluated using the datasets from 147 stations. In the east, north and upward directions, positioning accuracy of 1.8, 1.2 and 2.5 cm in the static mode, and of 6.7, 5.1 and 10.4 cm in the kinematic mode can be achieved for the BDS-3/BDS-2 real-time PPP, respectively, while the corresponding convergence time with a threshold of 10 cm is 32.9, 23.7 and 32.8 min, and 66.9, 42.9 and 69.1 min in the two modes in the three directions, respectively. To complete this, the availability of BDS-3/BDS-2 constellations, the quality of BDS-3/BDS-2 real-time precise satellite products, and the BDS-3/BDS-2 post-processed PPP solutions are also analyzed. For comparison, the results for the GPS are also presented.

scholarly journals Real-Time Global Ionospheric Map and Its Application in Single-Frequency Positioning

Sensors ◽  
2019 ◽  
Vol 19 (5) ◽  
pp. 1138 ◽  
Author(s):  
Liang Zhang ◽  
Yibin Yao ◽  
Wenjie Peng ◽  
Lulu Shan ◽  
Yulin He ◽  
...  
Keyword(s):  
Real Time ◽  
Total Electron Content ◽  
Precise Point Positioning ◽  
Single Frequency ◽  
Electron Content ◽  
Vertical Total Electron Content ◽  
Total Electron ◽  
Time Service ◽  
Point Positioning ◽  
Raw Observations

The prevalence of real-time, low-cost, single-frequency, decimeter-level positioning has increased with the development of global navigation satellite systems (GNSSs). Ionospheric delay accounts for most errors in real-time single-frequency GNSS positioning. To eliminate ionospheric interference in real-time single-frequency precise point positioning (RT-SF-PPP), global ionospheric vertical total electron content (VTEC) product is designed in the next stage of the International GNSS Service (IGS) real-time service (RTS). In this study, real-time generation of a global ionospheric map (GIM) based on IGS RTS is proposed and assessed. There are three crucial steps in the process of generating a real-time global ionospheric map (RTGIM): estimating station differential code bias (DCB) using the precise point positioning (PPP) method, deriving slant total electron content (STEC) from PPP with raw observations, and modeling global vertical total electron content (VTEC). Experiments were carried out to validate the algorithm’s effectiveness. First, one month’s data from 16 globally distributed IGS stations were used to validate the performance of DCB estimation with the PPP method. Second, 30 IGS stations were used to verify the accuracy of static PPP with raw observations. Third, the modeling of residuals was assessed in high and quiet ionospheric activity periods. Afterwards, the quality of RTGIM products was assessed from two aspects: (1) comparison with the Center for Orbit Determination in Europe (CODE) global ionospheric map (GIM) products and (2) determination of the performance of RT-SF-PPP with the RTGIM. Experimental results show that DCB estimation using the PPP method can realize an average accuracy of 0.2 ns; static PPP with raw observations can achieve an accuracy of 0.7, 1.2, and 2.1 cm in the north, east, and up components, respectively. The average standard deviations (STDs) of the model residuals are 2.07 and 2.17 TEC units (TECU) for moderate and high ionospheric activity periods. Moreover, the average root-mean-square (RMS) error of RTGIM products is 2.4 TECU for the one-month moderate ionospheric period. Nevertheless, for the high ionospheric period, the RMS is greater than the RMS in the moderate period. A sub-meter-level horizontal accuracy and meter-level vertical accuracy can be achieved when the RTGIM is employed in RT-SF-PPP.

Enabling robust and accurate navigation for UAVs using real-time GNSS precise point positioning and IMU integration

2020 ◽  
Vol 125 (1283) ◽  
pp. 87-108
Author(s):  
C. Chi ◽  
X. Zhan ◽  
S. Wang ◽  
Y. Zhai
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Three Dimensional ◽  
Coupled System ◽  
Measurement Unit ◽  
Satellite Geometry ◽  
Tightly Coupled ◽  
Point Positioning ◽  
Gnss Measurements ◽  
The One

ABSTRACTAccurate navigation is required in many Unmanned Aerial Vehicle (UAV) applications. In recent years, GNSS Precise Point Positioning (PPP) has been recognised as an efficient approach for providing precise positioning services. In contrast to the widely used Real-Time Kinematic (RTK), PPP is independent of reference stations, which greatly broadens its scope of application. However, the accuracy and reliability of PPP can be significantly decreased by poor GNSS satellite geometry and outage. In response, a real-time four-constellation GNSS PPP is applied to improve the geometry in this work, and PPP is tightly coupled with an Inertial Measurement Unit (IMU) to smooth the position and velocity output, thus improving the robustness of the navigation solution. Experimental flight tests are carried out using a UAV in an open-sky area, and GNSS-challenged environments are simulated. The results show that the four-constellation GNSS PPP/IMU integration reduces the Root-Mean-Square (RMS) Three-Dimensional (3D) positioning and velocity error by 76.4% and 67.1%, respectively, in open sky with respect to the one-GNSS PPP. Under scenarios where GNSS measurements are insufficient, the coupled system can still provide continuous solutions. Moreover, the coupled PPP/IMU system can also maintain the convergence of PPP during GNSS-challenged periods and can greatly shorten the re-convergence period of PPP when the UAV returns to the open sky.

scholarly journals A New Weighting Approach with Application to Ionospheric Delay Constraint for GPS/GALILEO Real-Time Precise Point Positioning

2018 ◽  
Vol 8 (12) ◽  
pp. 2537 ◽  
Author(s):  
Tianjun Liu ◽  
Jian Wang ◽  
Hang Yu ◽  
Xinyun Cao ◽  
Yulong Ge
Keyword(s):  
Data Processing ◽  
Real Time ◽  
Precise Point Positioning ◽  
Convergence Time ◽  
Improvement Rate ◽  
The Real ◽  
Weighted Residuals ◽  
Weight Factors ◽  
Filter Convergence ◽  
Point Positioning

The real-time precise point positioning (RT PPP) technique has attracted increasing attention due to its high-accuracy and real-time performance. However, a considerable initialization time, normally a few hours, is required in order to achieve the proper convergence of the real-valued ambiguities and other estimate parameters. The RT PPP convergence time may be reduced by combining quad-constellation global navigation satellite system (GNSS), or by using RT ionospheric products to constrain the ionosphere delay. But to improve the performance of convergence and achieve the best positioning solutions in the whole data processing, proper and precise variances of the observations and ionospheric constraints are important, since they involve the processing of measurements of different types and with different accuracy. To address this issue, a weighting approach is proposed by a combination of the weight factors searching algorithm and a moving-window average filter. In this approach, the variances of ionospheric constraints are adjusted dynamically according to the principle that the sum of the quadratic forms of weighted residuals is the minimum, and the filter is applied to combine all epoch-by-epoch weight factors within a time window. To evaluate the proposed approach, datasets from 31 Multi-GNSS Experiment (MGEX) stations during the period of DOY (day of year) 023-054 in 2018 are analyzed with different positioning modes and different data processing methods. Experimental results show that the new weighting approach can significantly improve the convergence performance, and that the maximum improvement rate reaches 35.9% in comparison to the traditional method of priori variance in the static dual-frequency positioning mode. In terms of the RMS (Root Mean Square) statistics of positioning errors calculated by the new method after filter convergence, the same accuracy level as that of RT PPP without constraints can be achieved.

Precise Point Positioning Model Using Triple GNSS Constellations: GPS, Galileo and BeiDou

2016 ◽  
Vol 10 (4) ◽  
Author(s):  
Akram Afifi ◽  
Ahmed El-Rabbany
Keyword(s):  
Real Time ◽  
Urban Areas ◽  
Precise Point Positioning ◽  
Convergence Time ◽  
Dual Frequency ◽  
Post Processing ◽  
International Gnss Service ◽  
Time Service ◽  
System Bias ◽  
Point Positioning

AbstractThis paper introduces a comparison between dual-frequency precise point positioning (PPP) post-processing model, which combines the observations of three different GNSS constellations, namely GPS, Galileo, and BeiDou and real-time PPP model. A drawback of a single GNSS system such as GPS, however, is the availability of sufficient number of visible satellites in urban areas. Combining GNSS observations offers more visible satellites to users, which in turn is expected to enhance the satellite geometry and the overall positioning solution. However, combining several GNSS observables introduces additional biases, which require rigorous modelling, including the GNSS time offsets and hardware delays. In this paper, a GNSS post-processing PPPP model is developed using ionosphere-free linear combination. The additional biases of the GPS, Galileo, and BeiDou combination are accounted for through the introduction of a new unknown parameter, which is identified as the inter-system bias, in the PPP mathematical model. Natural Resources Canada’s GPSPace PPP software is modified to enable a combined GPS / Galileo / BeiDou PPP solution and to handle the newly inter-system bias. A total of four data sets at four IGS stations are processed to verify the developed PPP model. Precise satellite orbit and clock products from the IGS-MGEX network are used to correct of the GPS, Galileo and BeiDou measurements. For the real-time PPP model the corrections of the satellites orbit and clock are obtained through the international GNSS service (IGS) real-time service (RTS). GPS and Galileo Observations are used for the GNSS RTS-IGS PPP model as the RTS-IGS satellite products are not available for BeiDou satellites. This paper provides the GNSS RTS-IGS PPP model using different satellite clock corrections namely: IGS01, IGC01, IGS01, and IGS03. All PPP models results of convergence time and positioning precision are compared to the traditional GPS-only PPP model. It is shown that combining GPS, Galileo, and BeiDou observations in a PPP model reduces the convergence time by 25 % compared with the GPS-only PPP model.

scholarly journals Analysis on the Potential Performance of GPS and Galileo Precise Point Positioning using Simulated Real-Time Products

2018 ◽  
Vol 72 (1) ◽  
pp. 19-33 ◽  
Author(s):  
Francesco Basile ◽  
Terry Moore ◽  
Chris Hill
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Satellite System ◽  
Convergence Time ◽  
Alternative Methods ◽  
International Gnss Service ◽  
Binary Offset Carrier ◽  
Time Service ◽  
Point Positioning ◽  
The Impact

With the evolving Global Navigation Satellite System (GNSS) landscape, the International GNSS Service (IGS) has started the Multi-GNSS Experiment (MGEX) to produce precise products for new generation systems. Various analysis centres are working on the estimation of precise orbits, clocks and bias for Galileo, Beidou and Quasi-Zenith Satellite System (QZSS) satellites. However, at the moment these products can only be used for post-processing applications. Indeed, the IGS Real-Time service only broadcasts Global Positioning System (GPS) and Globalnaya Navigatsionnaya Sputnikovaya Sistema (GLONASS) corrections. In this research, a simulator of multi-GNSS observations and real-time precise products has been developed to analyse the performance of GPS-only, Galileo-only and GPS plus Galileo Precise Point Positioning (PPP). The error models in the simulated orbits and clocks were based on the difference between the GPS Real-Time and the Final products. Multiple scenarios were analysed, considering different signals combined in the Ionosphere Free linear combination. Results in a simulated open area environment show better performance of the Galileo-only case over the GPS-only case. Indeed, up 33% and 29% of improvement, respectively, in the accuracy level and convergence time can be observed when using the full Galileo constellation compared to GPS. The dual constellation case provides good improvements, in particular in the convergence time (47% faster than GPS). This paper will also consider the impact of different linear combinations of the Galileo signals, and the potential of the E5 Alternative Binary Offset Carrier (AltBOC) signal. Even though it is significantly more precise than E5a, the PPP performance obtained with the Galileo E1-E5a combination is either better or similar to the one with Galileo E1-E5. The reason for this inconsistency was found in the use of the ionosphere free combination with E1. Finally, alternative methods of ionosphere error mitigation are considered in order to ensure the best possible positioning performance from the Galileo E5 signal in multi-frequency PPP.

scholarly journals Ocean Real-Time Precise Point Positioning with the BeiDou Short-Message Service

2020 ◽  
Vol 12 (24) ◽  
pp. 4167
Author(s):  
Kaifei He ◽  
Duojie Weng ◽  
Shengyue Ji ◽  
Zhenjie Wang ◽  
Wu Chen ◽  
...  
Keyword(s):  
Real Time ◽  
Data Transmission ◽  
Short Message Service ◽  
Precise Point Positioning ◽  
Maximum Size ◽  
Global Navigation Satellite Systems ◽  
Short Message ◽  
Time Service ◽  
Message Service ◽  
Point Positioning

Real-time precise point positioning (RTPPP) is a popular positioning method that uses a real-time service (RTS) product to mitigate various Global Navigation Satellite Systems (GNSS) errors. However, communication links are not available in the ocean. The use of a communication satellite for data transmission is so expensive that normal users could not afford it. The BeiDou short-message service provides an efficient option for data transmission at sea, with an annual fee of approximately 160 USD. To perform RTPPP using BeiDou short messages, the following two challenges should be appropriately addressed: the maximum size of each BeiDou message is 78 bytes, and the communication frequency is limited to once a minute. We simplify the content of RTS data to minimize the required bandwidth. Moreover, the orbit and clock corrections are predicted based on minute-interval RTS orbital and clock corrections. An experiment was conducted to test the performance of the proposed method. The numerical results show that the three-dimensional positioning precision can reach approximately 0.4 m with combined GPS + GLONASS and approximately 0.2 m with combined GPS + GLONASS + Galileo + BeiDou.

scholarly journals Validation and Assessment of Multi-GNSS Real-Time Precise Point Positioning in Simulated Kinematic Mode Using IGS Real-Time Service

2018 ◽  
Vol 10 (2) ◽  
pp. 337 ◽  
Author(s):  
Liang Wang ◽  
Zishen Li ◽  
Maorong Ge ◽  
Frank Neitzel ◽  
Zhiyu Wang ◽  
...  
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Time Service ◽  
Point Positioning

scholarly journals Precise Point Positioning Using Triple GNSS Constellations in Various Modes

2021 ◽  
Author(s):  
Akram Afifi ◽  
Ahmed El-Rabbany
Keyword(s):  
Linear Combination ◽  
Real Time ◽  
Precise Point Positioning ◽  
Satellite Orbit ◽  
Convergence Time ◽  
Dual Frequency ◽  
Post Processing ◽  
Time Service ◽  
Reference Satellite ◽  
Point Positioning

This paper introduces a new dual-frequency precise point positioning (PPP) model, which combines the observations from three different global navigation satellite system (GNSS) constellations, namely GPS, Galileo, and BeiDou. Combining measurements from different GNSS systems introduces additional biases, including inter-system bias and hardware delays, which require rigorous modelling. Our model is based on the un-differenced and between-satellite single-difference (BSSD) linear combinations. BSSD linear combination cancels out some receiver-related biases, including receiver clock error and non-zero initial phase bias of the receiver oscillator. Forming the BSSD linear combination requires a reference satellite, which can be selected from any of the GPS, Galileo, and BeiDou systems. In this paper three BSSD scenarios are tested; each considers a reference satellite from a different GNSS constellation. Natural Resources Canada’s GPSPace PPP software is modified to enable a combined GPS, Galileo, and BeiDou PPP solution and to handle the newly introduced biases. A total of four data sets collected at four different IGS stations are processed to verify the developed PPP model. Precise satellite orbit and clock products from the International GNSS Service Multi-GNSS Experiment (IGS-MGEX) network are used to correct the GPS, Galileo, and BeiDou measurements in the post-processing PPP mode. A real-time PPP solution is also obtained, which is referred to as RT-PPP in the sequel, through the use of the IGS real-time service (RTS) for satellite orbit and clock corrections. However, only GPS and Galileo observations are used for the RT-PPP solution, as the RTS-IGS satellite products are not presently available for BeiDou system. All post-processed and real-time PPP solutions are compared with the traditional un-differenced GPS-only counterparts. It is shown that combining the GPS, Galileo, and BeiDou observations in the post-processing mode improves the PPP convergence time by 25% compared with the GPS-only counterpart, regardless of the linear combination used. The use of BSSD linear combination improves the precision of the estimated positioning parameters by about 25% in comparison with the GPS-only PPP solution. Additionally, the solution convergence time is reduced to 10 minutes for the BSSD model, which represents about 50% reduction, in comparison with the GPS-only PPP solution. The GNSS RT-PPP solution, on the other hand, shows a similar convergence time and precision to the GPS-only counterpart.

Sign in / Sign up

Export Citation Format

Share Document