scholarly journals Optimization of pre-treatment of de-oiled oil seed cake for release of reducing sugars by response surface methodology

Bioethanol ◽  
2016 ◽  
Vol 2 (1) ◽  
Author(s):  
N Sharmada ◽  
Apoorva Punja ◽  
Sonali S Shetty ◽  
Vinayaka B Shet ◽  
Louella Concepta Goveas ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Sodium Hydroxide ◽  
Response Surface ◽  
Sulphuric Acid ◽  
Reducing Sugars ◽  
H2so4 Concentration ◽  
Pre Treatment ◽  
Alkali Hydrolysis ◽  
Optimized Conditions

AbstractPre-treatment is a process that releases simple sugars from complex lignocellulosic biomass by using chemicals like acid and alkali which are one of the simplest and cost effective techniques. In this study, the conditions for sulphuric acid and sodium hydroxide pretreatment of de-oiled oil seed cake (DOSC) were optimized by response surface methodology (RSM). The levels of factors (DOSC concentration, agitation speed, sulphuric acid (H2SO4), sodium hydroxide (NaOH) concentration and reaction time) that affect release of reducing sugars by pre-treatment were obtained by one factor at a time (OFAT) approach of which only H2SO4 concentration, NaOH concentration and reaction time showed significance. The levels of factors were optimized by central composite design. Optimized conditions were found to be 11.65% (v/v) of H2SO4 concentration at 1.28h and, 4 N of NaOH at 3.7 h for acid and alkali hydrolysis respectively. Under optimized conditions, the release of reducing sugars was found to be 0.69 g/L (41.36 mg RRS/ g cellulose) and 0.40 g/L (23.98 mg RRS/ g cellulose) for acid hydrolysis and alkali hydrolysis of DOSC, respectively. Hence, RSM was found to be an efficient technique to optimize the hydrolysis process and ensure maximum release of reducing sugars.

Enzyme-assisted Extraction for Optimized Recovery of Phenolic Bioactives from Peganum hermala Leaves Using Response Surface Methodology

2018 ◽  
Vol 17 (4) ◽  
pp. 349-354
Author(s):  
Qadir Rahman ◽  
Anwar Farooq ◽  
Amjad Gilani Mazhar ◽  
Nadeem Yaqoob Muhammad ◽  
Ahmad Mukhtar
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Enzyme Concentration ◽  
Coumaric Acid ◽  
Assisted Extraction ◽  
Pre Treatment ◽  
Optimized Conditions ◽  
Enzyme Complexes ◽  
Hydrolysis Of ◽  
Central Composite

This study investigates the effect of enzyme formulations (Zympex-014, Kemzyme dry-plus and Natuzyme) on recovery of phenolics from Peganum hermala (harmal) leaves, under optimized conditions using response surface methodology. As compared to the other enzyme complexes, the yield (34 g/100g) obtained through Zympex-014-assisted extraction was higher under optimized conditions such as time (75 min), temperature (70°C), pH (6.5) and enzyme concentration (5 g/100 g) using central composite design (CCD). Effectiveness of Zympex-014 towards hydrolysis of P. hermala leaves cell wall was examined by analyzing the control and enzyme-treated leave residues using scanning electron microscope (SEM). GC/MS characterization authenticated the presence of quercetin (1.44), gallic acid (0.23), caffeic acid (0.04), cinnamic acid (0.05), m-coumaric acid (0.23) and p-coumaric acid (0.37 μg/g) as the potent phenolics in Zympex-014 based extract. It can be concluded from the findings of the current work that pre-treatment of P. hermala leaves with Zympex-014 significantly enhanced the recovery of phenolics that supports its potential uses in the nutra-pharamaceutical industry.

scholarly journals Trans-Esterification Optimization Process for Biodiesel Production from Palm Kernel Oil using Response Surface Methodology

2021 ◽  
Vol 6 (2) ◽  
pp. 7-15
Author(s):  
T.O. Rabiu ◽  
N.A. Folami ◽  
N.A. Badiru ◽  
N.A. Kinghsley ◽  
B.T. Dare ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Sodium Hydroxide ◽  
Response Surface ◽  
Catalyst Concentration ◽  
Palm Kernel ◽  
Biodiesel Production ◽  
Optimization Process ◽  
Palm Kernel Oil ◽  
Kernel Oil

The ever-growing concern for the safety of lives and the environment as well as the depletion in fossil fuels reserves across the globe has led to the keen interests of many researchers in the field of renewable energy. This study was therefore undertaken to investigate the trans-esterification optimization process for biodiesel production from palm kernel using response surface methodology. The materials for the trans-esterification processes were palm kernel oil, Methanol and sodium hydroxide. The effects of reaction temperature (oC), catalyst concentration (wt%) and reaction time (min) on the yield were evaluated. The properties of the biodiesel produced showed that it met the ASTM standard for biodiesel. A quadratic polynomial model, Yield (%) = 78.60–3.12A–.62B + 0.00C -0.75AB – 3.50AC + 1.50BC + 2.82A2– 0.18B2 + 1.08C2, was developed that can be used to predict yield of biodiesel at any value of the different parameters investigated. The ANOVA for the model of the biodiesel yield obtained indicates that the models fit well in describing the relationship between the predictor (biodiesel yield) and the factors (methanol to oil ratio, catalyst concentration and reaction time). The optimal trans-esterification conditions were found to be 60°C for temperature, 60minutes for reaction time, 0.878w% of oil as Sodium hydroxide (catalyst) concentration and methanol/oil ratio of 1:6. At these optimal conditions, the biodiesel yield was fond to be 89.32% The generated biodiesel had high cetane number, better engine ignitability and poses lesser pollution problems than petroleum diesel.

Optimization Studies on Acid Hydrolysis of Pretreated Oil Palm Empty Fruit Bunch for Production of Xylose by Application of Response Surface Methodology

2013 ◽  
Vol 699 ◽  
pp. 77-82 ◽  
Author(s):  
S. Duangwang ◽  
C. Sangwichien
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Acid Hydrolysis ◽  
Response Surface ◽  
Reaction Temperature ◽  
Oil Palm ◽  
Temperature Reaction ◽  
Empty Fruit Bunch ◽  
H2so4 Concentration ◽  
Hydrolysis Of

Oil palm empty fruit bunch is a lignocellulosic material from palm oil plantations. It is a potential source of xylose which can be used as a raw material for production of xylitol. Using of lignocellulosic waste for bioconversion to fuels and chemicals is justifiable as these materials are low cost, renewable and widespread sources of sugars. The objective of the present study was to determine the effect of H2SO4 concentration, reaction temperature and reaction time for acid hydrolysis of pretreated OPEFB, pretreated OPEFB with reaction temperature, reaction time and NaOH concentration were 130 °C, 40 min and 15% (w/v), respectively to achieve high xylose yield. Batch reactions were carried out under various reaction temperature, reaction time and H2SO4 concentration. Response Surface Methodology (RSM) was followed to optimize acid hydrolysis in order to obtain high yield of xylose. The optimum reaction temperature, reaction time and H2SO4 concentration were found to be 140 °C, 90 min and 7% (w/v), respectively. The maximum value of xylose was obtained 56.39 g/l by using the above condition. The best result of xylose yield obtained was 126%.

scholarly journals Optimization of an Ultrasonic-Assisted Biodiesel Production Process from One Genotype of Rapeseed (TERI (OE) R-983) as a Novel Feedstock Using Response Surface Methodology

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2656 ◽  
Author(s):  
Sara Almasi ◽  
Barat Ghobadian ◽  
Gholam Hassan Najafi ◽  
Talal Yusaf ◽  
Masoud Dehghani Soufi ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Methyl Esters ◽  
Operating Conditions ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Climate Conditions ◽  
Ultrasonic Assisted ◽  
Optimized Conditions

In recent years, due to the favorable climate conditions of Iran, the cultivation of rapeseed has increased significantly. The aim of this study was to investigate the possibility of biodiesel production from one genotype of rapeseed (TERI (OE) R-983). An ultrasonic approach was used in order to intensify the reaction. Response surface methodology (RSM) was applied to identify the optimum conditions of the process. The results of this research showed that the conversion of biodiesel was found to be 87.175% under the optimized conditions of a 4.63:1 molar ratio (methanol to oil), 56.50% amplitude, and 0.4 s pulses for a reaction time of 5.22 min. Increasing the operating conditions, such as the molar ratio from 4:1 to 5.5:1, amplitude from 50% to 72.5%, reaction time from 3 min to 7 min, and pulse from 0.4 s to 1 s, increased the FAME (fatty acid methyl esters) yield by approximately 4.5%, 2.3%, 1.2%, and 0.5%, respectively. The properties of the TERI (OE) R-983 methyl ester met the requirements of the biodiesel standard (ASTM D6751), indicating the potential of the produced biodiesel as an alternative fuel.

Optimization on Influencing Factors of Fracture Toughness of Corundum-Mullite Toughened by In Situ Synthesized Mullite Whiskers by Response Surface Methodology

2012 ◽  
Vol 581-582 ◽  
pp. 819-822 ◽  
Author(s):  
Bin Meng ◽  
Jin Hui Peng
Keyword(s):  
Fracture Toughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Response Surface Method ◽  
Sintering Temperature ◽  
Surface Method ◽  
Mullite Whiskers ◽  
Optimized Conditions ◽  
Addition Amount

The corundum-mullite was toughened by in-situ synthesized mullite whiskers and the process parameters influencing the fracture toughness of corundum-mullite, such as sintering temperature, addition amount of AlF3 and V2O5, were optimized by means of response surface method. Corundum-mullite with fracture toughness of 9.44 MPa.m-1/2 could be obtained under the optimized conditions, i.e. sintering temperature of 1400°C, 4.8 wt.% of AlF3 and 5.8 wt.% of V2O5. The results showed that it was feasible to prepare corundum-mullite toughened by in-situ synthesized mullite whiskers by the optimized parameters. In addition, an accurate model based on response surface method was proposed to predict the experimental results.

Optimization of Magnesium Separation and Extraction from Boron Slurry Using Response Surface Methodology

2011 ◽  
Vol 366 ◽  
pp. 366-369
Author(s):  
Feng Gao ◽  
Rong Fu ◽  
Ming Yang Qian ◽  
Zhu Min Wang ◽  
Xiang Zhang
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Factorial Design ◽  
Response Surface ◽  
Reaction Temperature ◽  
Fractional Factorial Design ◽  
Design Criterion ◽  
Fractional Factorial ◽  
Effective Factors

Response surface methodology was used to optimize the soaking Mg leaching ratio from the boron slurry screened by 25 fractional factorial design. Five effective factors such as H2SO4 concentrations, reaction time, reaction temperature and stir velocity were tested by using 25 fractional factorial design criterion and three effective factors H2SO4 concentrations, reaction time and reaction temperature showed significant effect(P2SO4 concentrations of 0.29mol/l, reaction time of 90 min and reaction temperature of 50°C. Three runs of additional confirmation experiments were conducted. The mixture magnesium leaching value was 58.20%.

scholarly journals Optimization of Synthesis of Seleno-Sargassum fusiforme(Harv.) Setch. Polysaccharide by Response Surface Methodology, Its Characterization, and Antioxidant Activity

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Yu-Bin Ji ◽  
Fang Dong ◽  
Miao Yu ◽  
Long Qin ◽  
Dan Liu
Keyword(s):  
Antioxidant Activity ◽  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Reaction Temperature ◽  
Sargassum Fusiforme ◽  
Synthesis Conditions ◽  
Optimum Reaction ◽  
Series Of Experiments

The response surface methodology was employed to optimize the synthesis conditions of seleno-Sargassum fusiforme(Harv.) Setch. polysaccharide. Three independent variables (reaction time, reaction temperature, and ratio of Na2SeO3to SFPSI) were tested. Furthermore, the characterization and antioxidant activity of Se-SFPSIin vivowere investigated. The result showed that the actual experimental Se content of Se-SFPSI was 3.352 mg/g at the optimum reaction conditions of reaction time 8 h, reaction temperature 71°C, and ratio of Na2SeO3to SFPSIB 1.0 g/g. A series of experiments showed that the characterization of Se-SFPSIB was significantly different from that of SFPSIB. Additionally, antioxidant activity assay indicated that the Se-SFPSIB could increase catalase (CAT), superoxide dismutase (SOD), and glutathione peroxidase (GSH-Px) activity of mice bearing tumor S180in blood, heart, and liver while decreasing malondialdehyde (MDA) levels. It can be concluded that selenylation is a feasible approach to obtain seleno-polysaccharide which was utilized as highly biological medicine or functional food.

scholarly journals Optimization of Enzymatic Synthesis of Betulinic Acid Amide in Organic Solvent by Response Surface Methodology (RSM)

2019 ◽  
Vol 19 (4) ◽  
pp. 849
Author(s):  
Nurul Atikah Amin Yusof ◽  
Nursyamsyila Mat Hadzir ◽  
Siti Efliza Ashari ◽  
Nor Suhaila Mohamad Hanapi ◽  
Rossuriati Dol Hamid
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Reaction Temperature ◽  
Betulinic Acid ◽  
Enzymatic Synthesis ◽  
Acid Amide ◽  
Molar Ratio ◽  
Percentage Yield ◽  
Substrate Molar Ratio

Optimization of the lipase catalyzed enzymatic synthesis of betulinic acid amide in the presence of immobilized lipase, Novozym 435 from Candida antartica as a biocatalyst was studied. Response surface methodology (RSM) and 5-level-4-factor central-composite rotatable design (CCRD) were employed to evaluate the effects of the synthesis parameters, such as reaction time (20–36 h), reaction temperature (37–45 °C), substrate molar ratio of betulinic acid to butylamine (1:1–1:3), and enzyme amounts (80–120 mg) on the percentage yield of betulinic acid amide by direct amidation reaction. The optimum conditions for synthesis were: reaction time of 28 h 33 min, reaction temperature of 42.92 °C, substrate molar ratio of 1:2.21, and enzyme amount of 97.77 mg. The percentage yield of actual experimental values obtained 65.09% which compared well with the maximum predicted value of 67.23%. The obtained amide was characterized by GC, GCMS and 13C NMR. Betulinic acid amide (BAA) showed a better cytotoxicity compared to betulinic acid as the concentration inhibited 50% of the cell growth (IC50) against MDA-MB-231 cell line (IC50 < 30 µg/mL).

Sign in / Sign up

Export Citation Format

Share Document