A Triple Band-Notched UWB Antenna Using Folded Resonators

Frequenz ◽  
2019 ◽  
Vol 73 (1-2) ◽  
pp. 37-43
Author(s):  
Yi-Chao Zeng ◽  
Hou Zhang ◽  
Xue-Liang Min ◽  
Ying Zhang
Keyword(s):  
Parametric Study ◽  
Surface Current ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Test Results ◽  
Uwb Antenna ◽  
Good Agreement ◽  
Triple Band

Abstract A triple band-notched ultra-wideband (UWB) monopole antenna etching novel folded resonator on the radiating patch, ground and between the feeding-line, is presented in this paper. The tri-rejection bands are 5.1–6.1 GHz, 7.6–8.8 GHz and 10.1–10.8 GHz which have covered bands of WLAN and ITU 8 GHz. To analyze the principle of proposed antenna, the simulation of parametric study and distribution of surface current are carried out. The size of antenna is 32 mm×19 mm×1 mm. And the test results are in good agreement with the simulation, which indicate that the antenna is promising for UWB system.

scholarly journals Design of a Compact UWB Antenna with Triple Band-Notched Characteristics

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Qiang Wang ◽  
Yan Zhang
Keyword(s):  
Input Impedance ◽  
Impedance Matching ◽  
Ground Plane ◽  
Surface Current ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Uwb Antenna ◽  
Notch Band ◽  
Parametric Studies ◽  
Triple Band

A new compact ultra-wideband (UWB) antenna with triband-notched characteristics is presented. The structure of the proposed antenna is simple and symmetric. A modified ground is introduced to obtain a wide impedance bandwidth of 2.9–13.4 GHz withS11<-10 dB. By inserting two arc-shaped slots in the radiation patch, two sharp bands of 3.3–3.7 GHz and 5.15–5.35 GHz are notched. The notch band of 7.25–7.75 GHz is achieved by etching a U-shaped slot in the ground plane. The notched bands can be controlled, respectively, while the characteristics of the proposed UWB antenna almost keep completely unchanged at the unnotched frequencies. Equivalent circuit models, surface current distributions, and input impedance are applied to analyze the principle of the proposed UWB antenna. Parametric studies are given. Simulated and measured results show that the proposed antenna has good impedance matching, stable radiation patterns, and constant gain.

scholarly journals Design of a Planar Tri-Band Notch UWB Antenna for X-Band, WLAN, and WiMAX

2020 ◽  
Vol 10 (6) ◽  
pp. 6557-6562
Author(s):  
S. Alotaibi ◽  
A. A. Alotaibi
Keyword(s):  
Ground Plane ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Strip Line ◽  
Uwb Antenna ◽  
Notched Band ◽  
X Band ◽  
Measurement Results ◽  
Good Agreement ◽  
Triple Band

In this work, a new ultra-wideband (UWB) antenna design with 2.08GHz to 12GHz impedance bandwidth and triple-band specifications is presented. The proposed antenna is formed by a truncated square patch, a partial ground plane, and a 50Ω microstrip line. Three different types of slots were used in order to induce notched bands. A C-shaped slot is etched on the radiating patch to obtain a notched band in 3.31-4.21GHz for WiMAX. An inverted U-shaped slot in the micro-strip line induces a second notched band in order to reduce the interference with the WLAN [5.04-6.81GHz]. Finally, two inverted L-shaped slots around the micro-ribbon line on the ground plane allow the X-band [9.13 to 10.75GHz]. The antenna has dimensions of 32×28×1.6mm3. The Ansoft software (HFSS) was used to simulate the proposed structure. The simulation results are in good agreement with the measurement results. The antenna shows an omnidirectional radiation pattern.

scholarly journals Compact Size Triple Notched-bands UWB Antenna with Sharp Band-Rejection Characteristics at WiMAX and WLAN Bands

2018 ◽  
Vol 7 (3) ◽  
pp. 99-103 ◽  
Author(s):  
M. F. Habash ◽  
A. S. Tantawy ◽  
H. A. Atallah ◽  
A. B. Abdel-Rahman
Keyword(s):  
Monopole Antenna ◽  
Ultra Wideband ◽  
Good Frequency ◽  
Uwb Antenna ◽  
Feed Line ◽  
The Third ◽  
Compact Size ◽  
Sharp Band ◽  
Planar Monopole Antenna ◽  
Triple Band

In this paper, a compact triple band-notched Ultra Wideband (UWB) antenna with sharp band-elimination features and controlled notched bandwidths is proposed and discussed. The design is made up of a rectangular-shaped   patch UWB planar monopole antenna with double collections of band-notched configurations. The band-notched configurations are involved to produce the desired lower and upper stop bands with good frequency selectivity and suitable stop bandwidths. The first notch is realized by using a C-shaped slot etched in the radiating patch in order to eliminate the interference at the WiMAX (3.4 - 3.8 GHz) applications. The second and the third notches are realized together by using a pair of U-shaped resonators that are located beside the feed line in both sides to eliminate the interference with the lower WLAN (5.15–5.35 GHz) and the higher WLAN (5.725–5.825GHz) bands.  Additionally, the bandwidths of the lower and upper stop bands can be control separately by changing the parameters of the band-notched configurations. Furthermore, the suggested triple notched bands UWB antenna is optimized, fabricated, and measured for verification purposes. The measured results are close to the simulated ones.

A compact UWB antenna with triple band notch reconfigurability

2020 ◽  
pp. 1-7
Author(s):  
Lei Li ◽  
Jingchang Nan ◽  
Jing Liu ◽  
Chengjian Tao
Keyword(s):  
Coplanar Waveguide ◽  
Ring Resonators ◽  
Uwb Antenna ◽  
Split Ring ◽  
X Band ◽  
Compact Size ◽  
Nested Structure ◽  
P Type ◽  
Good Agreement ◽  
Triple Band

Abstract A compact ultrawideband (UWB) antenna with reconfigurable triple band notch characteristics is proposed in this paper. The antenna consists of a coplanar waveguide-fed top-cut circular-shaped radiator with two etched C-shaped slots, a pair of split-ring resonators (SRRs) on the backside and four p-type intrinsic n-type (PIN) diodes integrated in the slots and SRRs. By controlling the current distribution in the slots and SRRs, the antenna can realize eight band notch states with independent switch ability, which allows UWB to coexist with 5G (3.3–4.4 GHz)/WiMAX (3.3–3.6 GHz), WLAN (5.15–5.825 GHz), and X-band (7.9–8.4 GHz) bands without interference. By utilizing a nested structure of C-shaped slots and SRRs on the backside, a compact size of 18 × 19.5 mm2 is achieved along with multimode triple band notch reconfigurability. The antenna covers a bandwidth of 3.1–10.6 GHz. A prototype is fabricated and tested. The simulated and experimental results are in good agreement.

CPW-Fed 8-Shaped Monopole Antenna for Ultra Wideband Applications

Frequenz ◽  
2016 ◽  
Vol 70 (11-12) ◽  
Author(s):  
Sarthak Singhal ◽  
Amit Kumar Singh
Keyword(s):  
Group Delay ◽  
Coplanar Waveguide ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Radiation Patterns ◽  
Antenna Structure ◽  
Operating Frequency Range ◽  
Good Agreement ◽  
Delay Variation

AbstractA CPW-fed 8-shaped monopole antenna for ultra wideband applications is presented. It consists of a 8-shaped monopole and two quarter elliptical coplanar waveguide ground planes. An impedance bandwidth from 5.4 GHz to 23.83 GHz is achieved. The radiation patterns are observed to be omnidirectional and bidirectional in E-and H-plane respectively at lower resonances. At higher frequencies, the radiation patterns are found to be nearly omnidirectional in both planes. The group delay variation is also observed to be constant in the operating frequency range. A good agreement is found between the simulation and experimental results. The designed antenna structure has miniaturized dimensions and wider bandwidth as compared to other already reported monopole structures.

scholarly journals Printed UWB Antenna with Coupled Slotted Element for Notch-Frequency Function

2008 ◽  
Vol 2008 ◽  
pp. 1-8 ◽  
Author(s):  
X. L. Bao ◽  
M. J. Ammann
Keyword(s):  
Parametric Study ◽  
Return Loss ◽  
Measured Data ◽  
Monopole Antenna ◽  
Frequency Function ◽  
Uwb Antenna ◽  
Printed Monopole Antenna ◽  
Printed Monopole ◽  
Slotted Plate

A novel printed monopole antenna employing a slotted-plate, which is electromagnetically coupled to the microstrip-fed planar element, is proposed to provide notch-frequency function. This technique enables stopband characteristics with improved control, compared to placing the slot in the microstrip-fed element. A detailed investigation of the rejectband properties has been made for the UWB antenna. Measured data for the optimized case show the 10 dB return loss bandwidth to be 9.8 GHz (from 2.80 GHz to 12.60 GHz) with a notchband frequency from 5.15 GHz to 5.825 GHz. Propagation measurements indicate that the electromagnetically coupled slot provides a greater reduction in stopband gain for the three principal planes, compared to placing the slot in the fed element. This is desirable to mitigate interference from WLAN systems. A full parametric study of the antenna is presented.

scholarly journals Planar EBG Loaded UWB Monopole Antenna with Triple Notch Characteristics

2021 ◽  
Vol 11 (4) ◽  
pp. 294-304
Author(s):  
Vamshi Kollipara ◽  
Samineni Peddakrishna ◽  
Jayendra Kumar
Keyword(s):  
Wireless Local Area Network ◽  
Local Area Network ◽  
Coupling Effect ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Area Network ◽  
Distribution Analysis ◽  
Archimedean Spiral ◽  
Feed Line ◽  
Triple Band

A triple band-notched ultra-wideband (UWB) monopole antenna using a planar electromagnetic bandgap (EBG) design is proposed. The EBG unit cell composed by an Archimedean spiral and inter-digital capacitance demonstrates the notch frequencies. The antenna with EBG cells near the feed line occupies only 30 × 36 mm2 with triple band-rejection characteristics. The three notched bands at 4.2 GHz, 5.2 GHz, and 9.1 GHz can be used in C-band satellite downlink, wireless local area network (WLAN), and X-band radio location for naval radar or military required applications. In addition, the proposed design is flexible to tune different notched bands by altering the EBG dimensions. The parametric analysis is studied in details after placing the EBG unit cells near the feed line to show the coupling effect. The input impedance and surface current distribution analysis are also analyzed to understand the effect of EBG at notch frequencies. The proposed design prototype is fabricated and characterized. A fairly considerable agreement is observed between simulated and measured results.

scholarly journals A Jug-Shaped CPW-Fed Ultra-Wideband Printed Monopole Antenna for Wireless Communications Networks

2022 ◽  
Vol 12 (2) ◽  
pp. 821
Author(s):  
Sarosh Ahmad ◽  
Umer Ijaz ◽  
Salman Naseer ◽  
Adnan Ghaffar ◽  
Muhammad Awais Qasim ◽  
...  
Keyword(s):  
Wireless Communication ◽  
Low Cost ◽  
Coplanar Waveguide ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Uwb Antenna ◽  
Compact Size ◽  
Parametric Studies ◽  
Printed Monopole Antenna ◽  
Printed Monopole

A type of telecommunication technology called an ultra-wideband (UWB) is used to provide a typical solution for short-range wireless communication due to large bandwidth and low power consumption in transmission and reception. Printed monopole antennas are considered as a preferred platform for implementing this technology because of its alluring characteristics such as light weight, low cost, ease of fabrication, integration capability with other systems, etc. Therefore, a compact-sized ultra-wideband (UWB) printed monopole antenna with improved gain and efficiency is presented in this article. Computer simulation technology microwave studio (CSTMWS) software is used to build and analyze the proposed antenna design technique. This broadband printed monopole antenna contains a jug-shaped radiator fed by a coplanar waveguide (CPW) technique. The designed UWB antenna is fabricated on a low-cost FR-4 substrate with relative permittivity of 4.3, loss tangent of 0.025, and a standard height of 1.6 mm, sized at 25 mm × 22 mm × 1.6 mm, suitable for wireless communication system. The designed UWB antenna works with maximum gain (peak gain of 4.1 dB) across the whole UWB spectrum of 3–11 GHz. The results are simulated, measured, and debated in detail. Different parametric studies based on numerical simulations are involved to arrive at the optimal design through monitoring the effects of adding cuts on the performance of the proposed antennas. Therefore, these parametric studies are optimized to achieve maximum antenna bandwidth with relatively best gain. The proposed patch antenna shape is like a jug with a handle that offers greater bandwidth, good gain, higher efficiency, and compact size.

Sign in / Sign up

Export Citation Format

Share Document