scholarly journals Cure Kinetics, Bonding Performance, Thermal Degradation, and Biocidal Studies of Phenol-Formaldehyde Resins Modified with Crude Bio-oil Prepared from Ziziphus mauritiana Endocarps

BioResources ◽  
2014 ◽  
Vol 10 (1) ◽  
Author(s):  
Shakir Ahmad Shahid ◽  
Muhammad Ali ◽  
Zafar Iqbal Zafar
Keyword(s):  
Thermal Degradation ◽  
Phenol Formaldehyde ◽  
Cure Kinetics ◽  
Ziziphus Mauritiana ◽  
Bonding Performance ◽  
Bio Oil

scholarly journals Synthesis of Bio-Oilphenol-Formaldehyde Resins under Alkali Conditions

2020 ◽  
Vol 71 (1) ◽  
pp. 19-27
Author(s):  
Günay Özbay ◽  
Caglar Cekic ◽  
Muhammad Syarhabil Ahmad ◽  
Erkan Sami Kokten
Keyword(s):  
Shear Strength ◽  
Phenol Formaldehyde ◽  
Bonding Performance ◽  
Performance Requirements ◽  
Vacuum Pyrolysis ◽  
Treatment Conditions ◽  
Bio Oil ◽  
Dry Conditions ◽  
Ft Ir ◽  
Pre Treatment

In the present study, bio-oil produced from vacuum pyrolysis of woody biomass has been investigated as a source of chemical feedstock. Bio-based resins were produced using the bio- oil with phenol substitutions ranging from 10 to 30 wt%. The conventional GC/MS analysis was carried out for the evaluation of the chemical composition of bio-oil. TGA, DSC and FT-IR analyses were used in order to characterize the bio-oil-phenol-formaldehyde (BPF) resins. The bonding quality of wood samples bonded with the BPF resins was investigated under different pre-treatment conditions. The highest shear strength was observed for the control samples bonded with the laboratory PF resin. As the amount of bio-oil was increased up to 30 wt%, the shear strength of the samples decreased from 12.08 to 11.76 N/mm2. The bonding performance was not negatively affected by the combination of bio-oil under dry conditions. According to TS EN 12765 standard, the relevant performance requirements for bonded samples under dry conditions must be at least 10 N/mm2. Relating to the standard, all samples bonded with BPF resins obtained the requirements for durability class C1. Under wet conditions, the bonding performance was negatively affected by the addition of bio-oil. However, the BPF resins fulfilled the durability requirements for C1, C2, and C3 specified in EN 12765 (2002).

Preparation of highly phenol substituted bio-oil-phenol-formaldehyde adhesives with enhanced bonding performance using furfural as crosslinking agent

2018 ◽  
Vol 136 (4) ◽  
pp. 46995 ◽  
Author(s):  
Yanyan Cheng ◽  
Guanghui Sui ◽  
Huan Liu ◽  
Xiaofeng Wang ◽  
Xiaomin Yang ◽  
...  
Keyword(s):  
Phenol Formaldehyde ◽  
Crosslinking Agent ◽  
Bonding Performance ◽  
Bio Oil

scholarly journals Pyrolysis-GC/MS Analysis of Fast Growing Wood Macaranga Species

2021 ◽  
Vol 6 (1) ◽  
pp. 141-158
Author(s):  
R.R. Dirgarini J.N. Subagyono ◽  
Ying Qi ◽  
Alan L. Chaffee ◽  
Rudianto Amirta ◽  
Marc Marshall
Keyword(s):  
Thermal Degradation ◽  
Pyrolysis Temperature ◽  
Woody Biomass ◽  
Biofuel Production ◽  
Flash Pyrolysis ◽  
Fast Growing ◽  
Ms Analysis ◽  
Bio Oil ◽  
Different Temperatures ◽  
High Yields

Py-GC/MS analysis of six different species of fast growing Macaranga wood has been studied. Flash pyrolysis was conducted at different temperatures (250-850 oC) under a flow of helium followed by GC/MS analysis of the products. The total pyrolysis yields of the six different species of Macaranga were mostly between 40 and 90% within the range of pyrolysis temperature applied.  Pyrolysis of the woody biomass produced compounds which are mostly derived from thermal degradation or volatilization of lignin and cellulose/hemicellulose, the original major constituents of the biomass. The Py-GC/MS technique indicated that M. gigantea was the most potential species for biofuel production and the optimum pyrolysis temperature to produce high yields of bio-oil was 450 oC.

scholarly journals Infrared Surface Studies of Opaque or Scattering Materials Using Photothermal Beam Deflection Spectroscopy

1985 ◽  
Vol 2 (2) ◽  
pp. 131-150 ◽  
Author(s):  
M. J. D. Low ◽  
C. Morterra
Keyword(s):  
Thermal Degradation ◽  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Intermediate Temperature ◽  
Beam Deflection ◽  
Formaldehyde Resin ◽  
Ir Radiation ◽  
Surface Studies ◽  
Titanyl Sulphate

Infrared (IR) photothermal beam deflection spectroscopy (PBDS) is briefly described and some of its applications to studies of carbons and highly scattering materials are reviewed. PBDS is especially useful for the study of materials which absorb IR radiation very strongly or act as strong IR scatterers, so that conventional IR techniques fail. Application of PBDS to study the thermal degradation of a phenol-formaldehyde resin, the reaction of NH3 and H2O with the surfaces of intermediate-temperature chars, the effect of Fe3+ on the charring of cellulose, the dehydration of titanyl sulphate, and TiO2 pigments, are described.

Sign in / Sign up

Export Citation Format

Share Document