scholarly journals Thermodynamic and kinetic features of the formation of amorphous state in films during quenching from the vapor state

2021 ◽  
Vol 29 (1) ◽  
pp. 57-60
Author(s):  
V. F. Bashev ◽  
S. I. Ryabtsev ◽  
F. F. Dotsenko
Keyword(s):  
Amorphous State ◽  
Effective Rate ◽  
Vapor State ◽  
Amorphous Phases ◽  
Plasma Sputtering ◽  
Ion Plasma ◽  
Nanocrystalline And Amorphous ◽  
Good Agreement ◽  
Kinetic Features

The method of modernized ion-plasma sputtering produced metastable states, including nanocrystalline and amorphous phases in films, even in alloys whose components do not mixed in the liquid state. The effective rate of energy relaxation at different modes of precipitation is theoretically estimated to be 1012 -1014 K/s during ion-plasma sputtering of atoms. On thermodynamic and kinetic states, different active and passive parameters for amorphization during sputtering are analyzed. The receiving expressions are in good agreement with the experimental results and contribute to the determination of further steps to obtain an amorphous state.

scholarly journals The effect of Bi additives on the properties of Fe-Pt films

2019 ◽  
Vol 27 (2) ◽  
pp. 47-50
Author(s):  
V. F. Bashev ◽  
N. A. Kutseva ◽  
O. I. Kushnerov ◽  
S. I. Ryabtsev ◽  
O. V. Yelina ◽  
...  
Keyword(s):  
Coercive Force ◽  
X Ray Diffraction ◽  
Ceramic Substrates ◽  
Amorphous Phases ◽  
Sputtered Films ◽  
Plasma Sputtering ◽  
Ion Plasma ◽  
Metastable Structures ◽  
Nanocrystalline And Amorphous ◽  
Pt Films

Using the modernized three-electrode ion-plasma sputtering method, homogeneous thin films of FePt and Fe (Pt/Bi) were obtained. Films were deposited on NaCl and glass-ceramic substrates. The film thickness was 120-530 nm. In this case, the calculated cooling rate reached ~ 1012–1014 K/s. The structure of the FePt and Fe (Pt/Bi) films was investigated using X-ray diffraction and electron microscopy methods. It was established that metastable phases were formed in freshly sputtered films, including a supersaturated solid solution, a nanocrystalline and amorphous phases. It was determined that the obtained metastable structures are stable when heated to 540-880 K, depending on the composition. It was established that Bi additives significantly reduce the coercive force of films in the as-sputtered state. It was shown that a heat treatment increased the coercive force up to 36 kA/m in FePt films and up to 10 kA/m in Fe (Pt/Bi) films. The composition of Fe (Pt/Bi) films with a small value of the temperature coefficient of resistance (TCR ~3·10-5 K-1) was determined.

scholarly journals Physical properties and structure of vapor-quenched immiscible alloys

2018 ◽  
Vol 26 (1) ◽  
pp. 45-52
Author(s):  
V. F. Bashev ◽  
N. A. Kutseva ◽  
O. I. Kushnerov ◽  
S. I. Ryabtsev ◽  
S. N. Antropov
Keyword(s):  
Thin Film ◽  
Electrical Resistivity ◽  
Crystal Lattices ◽  
Amorphous Phases ◽  
Plasma Sputtering ◽  
Ion Plasma ◽  
Nanocrystalline And Amorphous ◽  
Constant Rate ◽  
Thermally Processed ◽  
Hysteretic Magnetic Properties

The method of modernized ion-plasma sputtering produced metastable states, including nanocrystalline and amorphous phases in films of Fe-Ag, Fe-Bi, Fe-Ag-Bi, Fe-Co-Ag and Ni-Ag alloys whose components do not mixed in the liquid state. The periods of the crystal lattices and the dimensions of the crystallites of the nonequilibrium phases in the fresh-sputtered state and after the heating are determined. The temperatures of the beginning and the end of the decomposition of metastable phases are established when heated at a constant rate. The electric and hysteretic magnetic properties of films in freshly dusted and thermally processed states are measured. The compositions and conditions for obtaining films with low values of the temperature coefficient of electrical resistivity (~ 10-5 K-1) and high coercive force (HC ~ 150 kA/m) are established. Such films can be promising for use as thin-film precision resistors and magnetic information carriers with an increased recording density.

Thermodynamics and Kinetics of Crystallization of Amorphous Si and Ge Produced by Ion Implantation

1983 ◽  
Vol 27 ◽  
Author(s):  
E.P. Donovan ◽  
F. Spaepen ◽  
D. Turnbull ◽  
J.M. Poate ◽  
D.C. Jacobson
Keyword(s):  
Noble Gas ◽  
Amorphous State ◽  
Heat Evolution ◽  
Precise Determination ◽  
Total Enthalpy ◽  
Kinetics Of Crystallization ◽  
Amorphous Si ◽  
Kinetics Of ◽  
Good Agreement

ABSTRACTAmorphous Si and Ge layers, produced by noble gas (Ar or Xe) implantation of single crystal substrates, have been crystallized in a differential scanning calorimeter (DSC). This technique allows determination of the growth velocity (which is proportional to the rate of heat evolution, ΔHac), and the total enthalpy of crystallization ΔHacAmorphous Ge was found to relax continuously to an amorphous state of lower free energy, with a total enthalpy of relaxation of 6.0 kJ.mole−1 before crystallization started. The regrowth velocity on (100) substrates,measured to be 4.2×1017 exp (−2.17eV/kT)Å/sec, is compared to other determinations. The value of ΔHac was found to be 11.66± 0.7 kJ.mole, in good agreement with ΔHac for amorphous Ge produced by other methods. For Si, ΔHac was determined to be 11.95± 0.7 kJ.mole without any evidence of heat release due to relaxation. The kinetics of crystallization measured by DSC are compared with those determined by other techniques. The effects of the implant profile on the regrowth velocity could also be observed directly in the DSC signal. The more accurate value of ΔHac allowed a more precise determination of the melting temperature of amorphous Si: Taℓ= 1420K.

COMPARATIVE ACTION OF VARIOUS OESTROGENIC COMPOUNDS ON MOUSE VAGINAL SIALIC ACIDS (II)

1969 ◽  
Vol 62 (4) ◽  
pp. 663-670 ◽  
Author(s):  
Lars Carlborg
Keyword(s):  
Sialic Acid ◽  
Response Curve ◽  
Sialic Acids ◽  
Clear Cut ◽  
Suitable Parameter ◽  
Sufficient Degree ◽  
Comparative Action ◽  
Relative Potencies ◽  
Good Agreement

ABSTRACT Oestrogens administered in lower doses than necessary to induce full cornification of the mouse vagina induce mucification. It was shown previously that the degree of mucification could be estimated by quantitative determination of sialic acids. A suitable parameter for oestrogen assay was the measurement of vaginal sialic acid concentration which exhibited a clear cut dose response curve. Eleven assays of various oestrogens were performed with this method. Their estimated relative potencies were in good agreement with other routine oestrogen assays. A statistically sufficient degree of precision was found. The sensitivity was of the same order, or slightly higher, than the Allen-Doisy test.

An Automated Method for the Determination of Serum Calcium with Glyoxal Bis (2-Hydroxyanil)

1967 ◽  
Vol 13 (6) ◽  
pp. 515-520 ◽  
Author(s):  
Genevieve Farese ◽  
Janice L Schmidt ◽  
Milton Mager
Keyword(s):  
Serum Calcium ◽  
Automated Analysis ◽  
Automated Method ◽  
Good Agreement

Abstract A completely automated analysis is described for the determination of serum calcium with glyoxal bis (2-hydroxyanil) solution (GBHA). The method is simple and precise, and the data obtained are in good agreement with results obtained by the manual GBHA procedure.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

scholarly journals An SPRi Biosensor for Determination of the Ovarian Cancer Marker HE4 in Human Plasma

Sensors ◽  
2021 ◽  
Vol 21 (10) ◽  
pp. 3567
Author(s):  
Beata Szymanska ◽  
Zenon Lukaszewski ◽  
Beata Zelazowska-Rutkowska ◽  
Kinga Hermanowicz-Szamatowicz ◽  
Ewa Gorodkiewicz
Keyword(s):  
Ovarian Cancer ◽  
Cancer Patients ◽  
Tumor Resection ◽  
Analytical Signal ◽  
Cancer Marker ◽  
Human Epididymis Protein 4 ◽  
Pearson Coefficient ◽  
Rabbit Polyclonal Antibody ◽  
Good Agreement

Human epididymis protein 4 (HE4) is an ovarian cancer marker. Various cut-off values of the marker in blood are recommended, depending on the method used for its determination. An alternative biosensor for HE4 determination in blood plasma has been developed. It consists of rabbit polyclonal antibody against HE4, covalently attached to a gold chip via cysteamine linker. The biosensor is used with the non-fluidic array SPRi technique. The linear range of the analytical signal response was found to be 2–120 pM, and the biosensor can be used for the determination of the HE4 marker in the plasma of both healthy subjects and ovarian cancer patients after suitable dilution with a PBS buffer. Precision (6–10%) and recovery (101.8–103.5%) were found to be acceptable, and the LOD was equal to 2 pM. The biosensor was validated by the parallel determination of a series of plasma samples from ovarian cancer patients using the Elecsys HE4 test and the developed biosensor, with a good agreement of the results (a Pearson coefficient of 0.989). An example of the diagnostic application of the developed biosensor is given—the influence of ovarian tumor resection on the level of HE4 in blood serum.

scholarly journals Potentiometric Surfactant Sensor Based on 1,3-Dihexadecyl-1H-benzo[d]imidazol-3-ium for Anionic Surfactants in Detergents and Household Care Products

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3627
Author(s):  
Nikola Sakač ◽  
Dubravka Madunić-Čačić ◽  
Dean Marković ◽  
Lucija Hok ◽  
Robert Vianello ◽  
...  
Keyword(s):  
Anionic Surfactants ◽  
Negative Impact ◽  
Ion Pair ◽  
Two Phase ◽  
Potentiometric Response ◽  
Titration Curves ◽  
Signal Change ◽  
Nernstian Slope ◽  
Good Agreement

A 1,3-dihexadecyl-1H-benzo[d]imidazol-3-ium-tetraphenylborate (DHBI-TPB) ion-pair implemented in DHBI-TPB surfactant sensor was used for the potentiometric quantification of anionic surfactants in detergents and commercial household care products. The DHBI-TPB ion-pair was characterized by FTIR spectroscopy and computational analysis which revealed a crucial contribution of the C–H∙∙∙π contacts for the optimal complex formation. The DHBI-TPB sensor potentiometric response showed excellent analytical properties and Nernstian slope for SDS (60.1 mV/decade) with LOD 3.2 × 10−7 M; and DBS (58.4 mV/decade) with LOD 6.1 × 10−7 M was obtained. The sensor possesses exceptional resistance to different organic and inorganic interferences in broad pH (2–10) range. DMIC used as a titrant demonstrated superior analytical performances for potentiometric titrations of SDS, compared to other tested cationic surfactants (DMIC > CTAB > CPC > Hyamine 1622). The combination of DHBI-TPB sensor and DMIC was successfully employed to perform titrations of the highly soluble alkane sulfonate homologues. Nonionic surfactants (increased concentration and number of EO groups) had a negative impact on anionic surfactant titration curves and a signal change. The DHBI-TPB sensor was effectively employed for the determination of technical grade anionic surfactants presenting the recoveries from 99.5 to 101.3%. The sensor was applied on twelve powered samples as well as liquid-gel and handwashing home care detergents containing anionic surfactants. The obtained results showed good agreement compared to the outcomes measured by ISE surfactant sensor and a two-phase titration method. The developed DHBI-TPB surfactant sensor could be used for quality control in industry and has great potential in environmental monitoring.

scholarly journals Bichromatic Photoassociation Spectroscopy for the Determination of Rotational Constants of Cs2 0 u + Long-Range State below the 6S1/2 + 6P1/2 Asymptote

Molecules ◽  
2020 ◽  
Vol 25 (17) ◽  
pp. 3963
Author(s):  
Jizhou Wu ◽  
Jie Ma ◽  
Yuqing Li ◽  
Wenliang Liu ◽  
Peng Li ◽  
...  
Keyword(s):  
Long Range ◽  
Spectroscopic Technique ◽  
Rigid Rotor ◽  
Simple Analysis ◽  
Rotational Constants ◽  
Vibrational Levels ◽  
Photoassociation Spectroscopy ◽  
Rotor Model ◽  
Good Agreement

This article demonstrates new observation of the high-resolution ro-vibrational bichromatic photoassociation spectra (BPAS) of Cs2 in the 0u+ long-range state below the asymptotes 6S1/2 + 6P1/2. By combining with a modulation spectroscopic technique, precise references of the frequency differences have been engineered through the BPAS, with which the rotational constants of low-lying vibrational levels of the Cs20u+ long-range state have been accurately determined by fitting the frequency differences to the non-rigid-rotor model. The rotational constants for the newly observed seven ro-vibrational levels are summarized and disagreement for the level ῦ = 498 is clarified. The rotational constants of different vibrational levels demonstrate strong perturbations of the related energy structures. A simple analysis is performed and shows good agreement with experimental results.

scholarly journals Tropospheric NO<sub>2</sub> column densities deduced from zenith-sky DOAS measurements in Shanghai, China, and their application to satellite validation

2009 ◽  
Vol 9 (11) ◽  
pp. 3641-3662 ◽  
Author(s):  
D. Chen ◽  
B. Zhou ◽  
S. Beirle ◽  
L. M. Chen ◽  
T. Wagner
Keyword(s):  
Satellite Data ◽  
Urban Site ◽  
Optical Absorption Spectroscopy ◽  
Vertical Column ◽  
Error Sources ◽  
Satellite Validation ◽  
Tropospheric No2 ◽  
Realistic Information ◽  
Good Agreement

Abstract. Zenith-sky scattered sunlight observations using differential optical absorption spectroscopy (DOAS) technique were carried out in Shanghai, China (31.3° N, 121.5° E) since December 2006. At this polluted urban site, the measurements provided NO2 total columns in the daytime. Here, we present a new method to extract time series of tropospheric vertical column densities (VCDs) of NO2 from these observations. The derived tropospheric NO2 VCDs are important quantities for the estimation of emissions and for the validation of satellite observations. Our method makes use of assumptions on the relative NO2 height profiles and the diurnal variation of stratospheric NO2 VCDs. The main error sources arise from the uncertainties in the estimated stratospheric slant column densities (SCDs) and the determination of tropospheric NO2 air mass factor (AMF). For a polluted site like Shanghai, the accuracy of our method is conservatively estimated to be <25% for solar zenith angle (SZA) lower than 70°. From simultaneously performed long-path DOAS measurements, the NO2 surface concentrations at the same site were observed and the corresponding tropospheric NO2 VCDs were estimated using the assumed seasonal NO2 profiles in the planetary boundary layer (PBL). By making a comparison between the tropospheric NO2 VCDs from zenith-sky and long-path DOAS measurements, it is found that the former provides more realistic information about total tropospheric pollution than the latter, so it's more suitable for satellite data validation. A comparison between the tropospheric NO2 VCDs from ground-based zenith-sky measurements and SCIAMACHY was also made. Satellite validation for a strongly polluted area is highly needed, but exhibits also a great challenge. Our comparison shows good agreement, considering in particular the different spatial resolutions between the two measurements. Remaining systematic deviations are most probably related to the uncertainties of satellite data caused by the assumptions on aerosol properties as well as the layer heights of aerosols and NO2.

Sign in / Sign up

Export Citation Format

Share Document