Solid state PbS Quantum dots /TiO2 Nanoparticles heterojunction solar cell

2012 ◽  
Vol 1390 ◽  
Author(s):  
Lioz Etgar ◽  
Michael Grätzel
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Solid State ◽  
Short Circuit ◽  
Open Circuit ◽  
Layer By Layer ◽  
Heterojunction Solar Cells ◽  
Layer Deposition ◽  
Pbs Quantum Dots ◽  
Open Circuit Photovoltage

ABSTRACTSolid state PbS Quantum Dots (QDs)/TiO2 Nanoparticles heterojunction solar cells were produced by depositing PbS QDs on a 500nm thick Mesoscopic TiO2 films using layer-by-layer deposition. The heterojunction solar cells show photovoltaic response from the visible to the near infra-red region. Importantly, the PbS QDs act here as photosensitizers and at the same time as hole conductors. The PbS QDs/TiO2 device produces a remarkable short circuit photocurrent (Jsc) of 16.3 mA/cm2, an open circuit photovoltage (Voc) of 0.54 V and a fill factor (FF) of 0.41, corresponding to a light to electric power conversion efficiency (η) of 4.04% under 0.9 sun intensity.

Improving Charge Transport in PbS Quantum Dot to Al:ZnO Layer by Changing the Size of Quantum Dots in Hybrid Solar Cells

2016 ◽  
Vol 71 (11) ◽  
pp. 1067-1071
Author(s):  
Masood Mehrabian ◽  
Parinaz Abdollahian
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Short Circuit ◽  
Visible Region ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Hybrid Solar Cells ◽  
Photovoltaic Properties ◽  
Photovoltaic Applications ◽  
Pbs Quantum Dots

AbstractPbS Quantum dots and P3HT are promising materials for photovoltaic applications due to their absorption in the NIR and visible region, respectively. Our previous experimental work showed that doping Al to ZnO lattice (Al:ZnO) could efficiently improve the cell performance. In this article, hybrid solar cells containing of two active areas with ITO/Al:ZnO/PbS QDs/P3HT&PCBM/Ag structure were fabricated and the effect of PbS QD size on photovoltaic properties was investigated. Optimised solar cell showed maximum power conversion efficiency of 2.45 % with short-circuit current of 9.36 mA/cm2 and open-circuit voltage of 0.59 V under 1 sun illumination (AM1.5).

Thiocyanate Free Ruthenium(II) Complexes for Dye Sensitized Solar Cells (DSSCs)

2018 ◽  
Vol 382 ◽  
pp. 369-373
Author(s):  
Usana Mahanitipong ◽  
Preeyapat Prompan ◽  
Rukkiat Jitchati
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Visible Region ◽  
Photocurrent Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Ligand Charge Transfer ◽  
Sensitized Solar Cells ◽  
Open Circuit Photovoltage

The four thiocyanate free ruthenium(II) complexes; [Ru(N^N)2(C^N)]PF6were synthesized and characterized for dye sensitized solar cells (DSSCs). The results showed that the broad absorptions covered the visible region from metal to ligand charge transfer (MLCT) were obtained with the main peaks at 560, 490 and 400 nm. The materials were studied DSSC performance under standard AM 1.5. Compound PP1 showed the power conversion efficiency (PCE) at 3.10%, with a short-circuit photocurrent density (Jsc) of 7.99 mA cm-2, an open-circuit photovoltage (Voc) of 563 mV and a high fill factor (ff) of 0.690.

scholarly journals PbS Quantum Dots: Size, Ligand Dependent Energy Level Structures and Their Effects on the Performance of Heterojunction Solar Cells

2016 ◽  
Vol 31 (9) ◽  
pp. 915 ◽  
Author(s):  
WANG Heng ◽  
ZHAI Guang-Mei ◽  
ZHANG Ji-Tao ◽  
YANG Yong-Zhen ◽  
LIU Xu-Guang ◽  
...  
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Energy Level ◽  
Heterojunction Solar Cells ◽  
Pbs Quantum Dots

scholarly journals CdSe Quantum Dots Sensitized Mesoporous TiO2Solar Cells with CuSCN as Solid-State Electrolyte

2011 ◽  
Vol 2011 ◽  
pp. 1-5 ◽  
Author(s):  
Guanbi Chen ◽  
Lei Wang ◽  
Yu Zou ◽  
Xia Sheng ◽  
Hongjuan Liu ◽  
...  
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Solid State ◽  
Barrier Layer ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Cdse Quantum Dots ◽  
Solid State Electrolyte ◽  
Capping Agents ◽  
Organic Capping

Mesoporous TiO2is functionalized by 3-mercaptopropyl trimethyoxysilane (MPTMS) to anchor CdSe quantum dots (QDs). The resulting TiO2/CdSe is combined with solid-state electrolyte (CuSCN) to form solar cells. It is found that the efficiency of electron injection from QDs to TiO2can be improved owing to the substitution of the long chains of organic capping agents at the surface of QDs with MPTMS. The hydrolyzate of MPTMS forms an insulating barrier layer to reduce the recombination at the TiO2/CdSe interface, leading to the increase of open-circuit voltage (Voc).

scholarly journals Molecular Weight Effects of Biscarbazole-Based Hole Transport Polymers on the Performance of Solid-State Dye-Sensitized Solar Cells

Nanomaterials ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 2516
Author(s):  
Minseon Kong ◽  
Kyeong Seok Kim ◽  
Nguyen Van Nga ◽  
Yeonju Lee ◽  
Yu Seong Jeon ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Solar Cells ◽  
Solid State ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Dye Sensitized ◽  
Liquid Electrolytes ◽  
Sensitized Solar Cells

The leakage and volatilization of liquid electrolytes limit the commercialization of dye-sensitized solar cells (DSCs). As solid-state (ss) hole-transporting materials, free from leakage and volatilization, biscarbazole-based polymers with different molecular weights (PBCzA-H (21,200 g/mol) and PBCzA-L (2450 g/mol)) were applied in combination with additives to produce ssDSCs. An ssDSC with PBCzA-H showed a better short-circuit current (Jsc), open-circuit voltage (Voc), and fill factor (FF) than a device with PBCzA-L, resulting in 38% higher conversion efficiency. Compared to the PBCzA-L, the PBCzA-H with a higher molecular weight showed faster hole mobility and larger conductivity, leading to elevations in Jsc via rapid hole transport, Voc via rapid hole extraction, and FF via lowered series and elevated shunt resistances. Thus, it is believed that PBCzA-H is a useful candidate for replacing liquid electrolytes.

Simulation of InAIN/Si Single-Heterojunction Solar Cells Using wxAMPS

2014 ◽  
Vol 665 ◽  
pp. 111-114 ◽  
Author(s):  
Ying Huang ◽  
Xiao Ming Shen ◽  
Xiao Feng Wei
Keyword(s):  
Solar Cells ◽  
Fill Factor ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Indium Content ◽  
Open Circuit ◽  
Heterojunction Solar Cells ◽  
Si Solar Cells

In this paper, InAlN/Si single-heterojunction solar cells have been theoretically simulated based on wxAMPS software. The photovoltaic parameters, such as open circuit voltage, short circuit current, fill factor and conversion efficiency were investigated with changing the indium content and thickness of n-InAlN layer. Simulation results show that the optimum efficiency of InAlN/Si solar cells is 23.1% under AM 1.5G spectral illuminations, with the indium content and thickness of n-InAlN layer are 0.65 and 600nm, respectively. The simulation would contribute to design and fabricate high efficiency InAlN/Si solar cells in experiment.

scholarly journals Optical Property and Photoelectrical Performance of a Low-bandgap Conducting Polymer Incorporated with Quantum Dots Used for Organic Solar Cells

2015 ◽  
Vol 25 (2) ◽  
pp. 139
Author(s):  
Tran Thi Thao ◽  
Vu Thi Hai ◽  
Nguyen Nang Dinh ◽  
Le Dinh Trong
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Low Bandgap ◽  
A Value

By using spin-coating technique, a low bandgap conjugated polymer, poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopen-ta[2,1-b;3,4-b′]dithiophene)-alt-4,7-(2,1,3-benzothiadiazole)] (PCPDTBT)  and its composite thin films have been prepared. The optical absorption and photoconductive properties with over a wide spectral range, from 350 to 950  nm, were characterized. The obtained results showed that PCPDTBT:10 wt% CdSe  composite is the most suitable for efficient light-harvesting in polymer-based photovoltaic cells. The photoelectrical conversion efficiency (PCE) of the device with  a multilayer structure of ITO/PEDOT/ PCPDTBT:CdSe /LiF/Al  reached a value as large as 1.34% with an open-circuit voltage (Voc) = 0.57 V, a short-circuit current density (Jsc) = 4.29 mA/cm2, and a fill factor (FF) = 0.27. This suggests a useful application in further fabrication of quantum dots/polymers based solar cells.

Solution-Processed Heterojunction Solar Cells Based on p-type PbS Quantum Dots and n-type Bi2S3 Nanocrystals

2011 ◽  
Vol 23 (32) ◽  
pp. 3712-3717 ◽  
Author(s):  
Arup K. Rath ◽  
Maria Bernechea ◽  
Luis Martinez ◽  
Gerasimos Konstantatos
Keyword(s):  
Quantum Dots ◽  
Solar Cells ◽  
Solution Processed ◽  
Heterojunction Solar Cells ◽  
P Type ◽  
Pbs Quantum Dots

scholarly journals Effect of the Phosphorus Gettering on Si Heterojunction Solar Cells

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Hyomin Park ◽  
Sung Ju Tark ◽  
Chan Seok Kim ◽  
Sungeun Park ◽  
Young Do Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Solar Simulator ◽  
Heterojunction Solar Cells ◽  
Crystalline Silicon Solar Cells

To improve the efficiency of crystalline silicon solar cells, should be collected the excess carrier as much as possible. Therefore, minimizing the recombination both at the bulk and surface regions is important. Impurities make recombination sites and they are the major reason for recombination. Phosphorus (P) gettering was introduced to reduce metal impurities in the bulk region of Si wafers and then to improve the efficiency of Si heterojunction solar cells fabricated on the wafers. Resistivity of wafers was measured by a four-point probe method. Fill factor of solar cells was measured by a solar simulator. Saturation current and ideality factor were calculated from a dark current density-voltage graph. External quantum efficiency was analyzed to assess the effect of P gettering on the performance of solar cells. Minority bulk lifetime measured by microwave photoconductance decay increases from 368.3 to 660.8 μs. Open-circuit voltage and short-circuit current density increase from 577 to 598 mV and 27.8 to 29.8 mA/cm2, respectively. The efficiency of solar cells increases from 11.9 to 13.4%. P gettering will be feasible to improve the efficiency of Si heterojunction solar cells fabricated on P-doped Si wafers.

Sign in / Sign up

Export Citation Format

Share Document