Effect of boron on the continuous cooling transformation kinetics in a low carbon advanced ultra-high strength steel (A-UHSS)

2012 ◽  
Vol 1485 ◽  
pp. 83-88 ◽  
Author(s):  
G. Altamirano ◽  
I. Mejía ◽  
A. Hernández-Expósito ◽  
J. M. Cabrera
Keyword(s):  
Research Work ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Characterization ◽  
Low Carbon ◽  
Transformation Kinetics ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Cct Diagrams

ABSTRACTThe aim of the present research work is to investigate the influence of B addition on the phase transformation kinetics under continuous cooling conditions. In order to perform this study, the behavior of two low carbon advanced ultra-high strength steels (A-UHSS) is analyzed during dilatometry tests over the cooling rate range of 0.1-200°C/s. The start and finish points of the austenite transformation are identified from the dilatation curves and then the continuous cooling transformation (CCT) diagrams are constructed. These diagrams are verified by microstructural characterization and Vickers micro-hardness. In general, results revealed that for slower cooling rates (0.1-0.5 °C/s) the present phases are mainly ferritic-pearlitic (F+P) structures. By contrast, a mixture of bainitic-martensitic structures predominates at higher cooling rates (50-200°C/s). On the other hand, CCT diagrams show that B addition delays the decomposition kinetics of austenite to ferrite, thereby promoting the formation of bainitic-martensitic structures. In the case of B microalloyed steel, the CCT curve is displaced to the right, increasing the hardenability. These results are associated with the ability of B atoms to segregate towards austenitic grain boundaries, which reduce the preferential sites for nucleation and development of F+P structures.

Experimental Determination of Continuous Cooling Transformation Diagrams of Hot-Rolled Heat Treatable Steel Plates Using Quenching Dilatometry

2016 ◽  
Vol 1812 ◽  
pp. 129-134 ◽  
Author(s):  
Gerardo Altamirano-Guerrero ◽  
Emmanuel J. Gutiérrez-Castañeda ◽  
Omar García-Rincón ◽  
Armando Salinas-Rodríguez
Keyword(s):  
Phase Transformation ◽  
Solid Phase ◽  
Microstructural Characterization ◽  
Steel Plates ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Transformation Diagrams ◽  
Hot Rolled ◽  
Cct Diagrams

ABSTRACTThis article outlines the use of quenching dilatometry in phase transformation kinetics research in steels under continuous cooling conditions. For this purpose, the phase transformation behavior of a hot-rolled heat treatable steel was investigated over the cooling rate range of 0.1 to 200 °C/s. The start and finish points of the austenite transformation were identified from the dilatometric curves and then the continuous cooling transformation (CCT) diagrams were constructed. The experimental CCT diagrams were verified by microstructural characterization using scanning electron microscopy (SEM) and Vickers micro-hardness. In general, results revealed that the quenching dilatometry technique is a powerful tool for the characterization and study of solid-solid phase transformations in steels. For cooling rates between 200 and 25 °C/s the final microstructure consists on plate-like martensite with the highest hardness values. By contrast, a mixture of phases of ferrite, bainite and pearlite predominated for slower cooling rates (10-0.1 °C/s).

Influence of Chromium Content and Prior Deformation on the Continuous Cooling Transformation Diagram of Low-Carbon Bainitic Steels

2020 ◽  
Vol 835 ◽  
pp. 58-67
Author(s):  
Mohammed Ali ◽  
Antti J. Kaijalainen ◽  
Jaakko Hannula ◽  
David Porter ◽  
Jukka I. Kömi
Keyword(s):  
Cooling Rate ◽  
Hot Deformation ◽  
Laser Scanning ◽  
Chromium Content ◽  
Bainitic Ferrite ◽  
Granular Bainite ◽  
Low Carbon ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling

The effect of chromium content and prior hot deformation of the austenite on the continuous cooling transformation (CCT) diagram of a newly developed low-carbon bainitic steel has been studied using dilatometer measurements conducted on a Gleeble 3800 simulator with cooling rates ranging from 2-80 °C/s. After austenitization at 1100 °C, specimens were either cooled without strain or given 0.6 strain at 880 °C prior to dilatometer measurements. The resultant microstructures have been studied using laser scanning confocal microscopy, scanning electron microscopy and macrohardness measurements. CCT and deformation continuous cooling transformation (DCCT) diagrams were constructed based on the dilatation curves, final microstructures and hardness values. Depending on the cooling rate, the microstructures of the investigated steels after cooling from the austenite region consist of one or more of the following microstructural components: lath-like upper bainite, i.e. bainitic ferrite (BF), granular bainite (GB), polygonal ferrite (PF) and pearlite (P). The proportion of BF to GB as well as the hardness of the transformation products decreased with decreasing cooling rate. The cooling rate at which PF starts to appear depends on the steel composition. With both undeformed and deformed austenite, increasing the chromium content led to higher hardenability and refinement of the microstructure, promoting the formation of BF and shifting the ferrite start curve to lower cooling rates. Prior hot deformation shifted the transformation curves to shorter times and higher temperatures and led to a reduction in hardness at the low cooling rates through the promotion of ferrite formation.

Development of an Empirical Model to Characterize Fracture Behavior During Forming of Advanced High Strength Steels Under Bending Dominated Conditions

2012 ◽  
Vol 134 (3) ◽  
Author(s):  
S. Sriram ◽  
H. Yao ◽  
N. Ramisetti
Keyword(s):  
Research Work ◽  
High Strength Steels ◽  
High Strength ◽  
Optical Microscope ◽  
Low Carbon ◽  
Thickness Strain ◽  
Bending Tests ◽  
Advanced High Strength Steels ◽  
Applied Tension ◽  
Ahss Steel

Higher strength advanced high-strength steels (AHSS) such as DP780 and DP980 are more susceptible to fractures at bend radii during press stampings in comparison with more ductile low carbon sheet steels used by the automotive industry. Most research work to develop predictive guidelines for preventing failures at bend radii have centered on determining critical R/t ratios to avoid failures caused by bending. In this paper, results from bending tests with and without applied tension conducted on a number of AHSS steel lots to generate different conditions for fracture are presented. For bending tests with applied tension, measures of overall formability as a function of R/t ratio of the punch are presented. Consistent with other studies reported in literature, the overall formability was found to increase with increasing R/t ratio reaching saturation for higher R/t ratios. In addition, local formability was determined for all the bending tests by measuring the thickness strains at failure using an optical microscope. It was observed that the thickness strain at failure was dependent on the R/t ratio and the loading mode. Examination of fracture surfaces from the different tests using an SEM reveals that fracture initiation occurs primarily at the ferrite/martensite interphase boundary. To analyze the local loading conditions leading to fracture, 2D finite element analyses (FEA) of the different bending tests using ABAQUS standard were conducted. Results of the FEA were analyzed, and a parameter describing bending dominance in a stamping process was isolated. An empirical fracture criterion relating the thickness strain at fracture as a function of this parameter was developed. Implications of the generated results and their applications for part design and evaluation of stamping feasibility are also discussed.

Effects of Vanadium on the Continuous Cooling Transformation of 0.7 %C Steel for Railway Wheels

2016 ◽  
Vol 367 ◽  
pp. 60-67 ◽  
Author(s):  
Solange T. Fonseca ◽  
Amilton Sinatora ◽  
Antonio J. Ramirez ◽  
Domingos J. Minicucci ◽  
Conrado R. Afonso ◽  
...  
Keyword(s):  
Room Temperature ◽  
Initial Temperature ◽  
Volume Fraction ◽  
Martensite Formation ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Xrd Techniques ◽  
Railway Wheels ◽  
Cct Diagrams

To understand the effect of vanadium on the austenite decomposition of a 0.7 %C steel used in railway wheels the Continuous Cooling Transformation (CCT) diagrams were obtained and the microstructures analyzed with optical, SEM, TEM and XRD techniques. Vanadium refined the austenitic grain (12 and 6 μm for 7C and 7V, respectively), what can be explain by the presence of fine (10 nm in diameter) V4C3 precipitates, which restricts the austenitic grain growth. In addition, vanadium, in solid solution, reduced the pearlite interlamelar spacing (0.13 and 0.11 μm for 7C and 7V, respectively) by depressing the initial temperature pearlite formation (644 and 639 °C for 7C and 7V, respectively). He increased the ferrite volume fraction from 1 to 3 % at cooling rate of 1 oC/s, due the fact that vanadium is a ferrite stabilizer. Vanadium addition did not affect the initial temperature for martensite formation, but increased the hardenability with martensite formation at slower cooling rates (10 and 5 oC/s for 7C and 7V, respectively). For higher cooling rates (20 to 100 oC/s), the austenite transformation to martensite at room temperature was incomplete and all steels presented martensite and retained austenite, which volumetric fraction was near the same for both steels varying from 20 to 40 %.

scholarly journals Dilatometric Analysis of the Austenite Decomposition in Undeformed and Deformed Low-Carbon Structural Steel

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5443
Author(s):  
Mateusz Morawiec ◽  
Adam Skowronek ◽  
Mariusz Król ◽  
Adam Grajcar
Keyword(s):  
Phase Transformation ◽  
Structural Steel ◽  
Transformation Product ◽  
Low Carbon ◽  
Transformation Kinetics ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Phase Transformation Kinetics ◽  
Microscopic Studies ◽  
Carbon Structural Steel

This paper aims to analyze the effect of deformation on the phase transformation kinetics of low-carbon structural steel. The steel used for the investigation was subjected to two different dilatometric analyses using a DIL 805A/D device. The first analysis was to determine the phase transformation kinetics without deformation of austenite before cooling. Then, the analysis under deformation conditions was conducted to investigate the deformation effect on the transformation kinetics. Microscopic studies by light microscopy were performed. The essential part of the research was hardness analysis for different cooling rates and the creation of continuous-cooling-transformation (CCT) and deformation continuous-cooling-transformation (DCCT) diagrams. It was found that the deformation of the samples before cooling increases a diffusion rate in the austenite resulting in the corresponding increase of ferritic, pearlitic, and bainitic start temperatures, as well as shifting the austenite transformation product regions to a longer time. The increase of the transformation area and a decrease in grain size are observed for the deformed samples.

scholarly journals Experimental Determination of Continuous Cooling Transformation (CCT) Diagrams for Dual-Phase Steels from the Intercritical Temperature Range

Metals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 674 ◽  
Author(s):  
Krishna Bräutigam–Matus ◽  
Gerardo Altamirano ◽  
Armando Salinas ◽  
Alfredo Flores ◽  
Frank Goodwin
Keyword(s):  
Low Carbon Steel ◽  
Dual Phase ◽  
Low Carbon ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Hardness Tests ◽  
Wide Range ◽  
Two Phases ◽  
C Partitioning ◽  
Cct Diagrams

The phase transformation kinetics under continuous cooling conditions for intercritical austenite in a cold rolled low carbon steel were investigated over a wide range of cooling rates (0.1–200 ∘ C/s). The start and finish temperatures of the intercritical austenite transformation were determined by quenching dilatometry and a continuous cooling transformation (CCT) diagram was constructed. The resulting experimental CCT diagram was compared with that calculated via JMatPro software, and verified using electron microscopy and hardness tests. In general, the results reveal that the experimental CCT diagram can be helpful in the design of thermal cycles for the production of different grades of dual-phase–advanced high-strengh steels (DP-AHSS) in continuous processing lines. The results suggest that C enrichment of intercritical austenite as a result of heating in the two phases (ferrite–austenite) region and C partitioning during the formation of pro-eutectoid ferrite on cooling significantly alters the character of subsequent austenite phase transformations.

Mechanical properties and microstructure of low carbon ultra-high strength steels (UHSS) microalloyed with boron

2012 ◽  
Vol 1373 ◽  
Author(s):  
I. Mejía ◽  
A. García de la Rosa ◽  
A. Bedolla-Jacuinde ◽  
J.M. Cabrera
Keyword(s):  
Mechanical Properties ◽  
Research Work ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Low Carbon ◽  
Advanced High Strength Steels ◽  
New Family ◽  
Ultra High Strength Steels ◽  
Hot Rolled

ABSTRACTThe aim of this research work is to study the effect of boron addition on mechanical properties and microstructure of a new family of low carbon NiCrVCu advanced high strength steels (AHSS). Experimental steels are thermo-mechanically processed (TMP) (hot-rolled+quenched). Results show that the microstructure of these steels contains bainite and martensite, predominantly, which nucleate along prior austenite grain boundaries (GB). On the other hand, tensile tests reveal that the TMP steels have YS (0.2% offset) of 978 MPa, UTS of 1140 MPa and EL of 18%. On the basis of exhibited microstructure and mechanical properties, these experimental steels are classified as bainitic-martensitic complex phase (CP) advanced ultra-high strength steels (UHSS).

Sign in / Sign up

Export Citation Format

Share Document