Effect of Deposition-Induced Annealable Defects on Light-Induced Defect Generation in a-Si:H

1993 ◽  
Vol 297 ◽  
Author(s):  
Jong-Hwan Yoon
Keyword(s):  
Amorphous Silicon ◽  
Defect Density ◽  
Hydrogenated Amorphous Silicon ◽  
Generation Rate ◽  
Defect Generation ◽  
Saturated State ◽  
Microscopic Models ◽  
Hydrogenated Amorphous ◽  
Substrate Temperatures

In this paper we present a method to determine the annealable defect density(ΔNann) present in hydrogenated amorphous silicon(a-Si:H). The effects of the annealable defects on the light-induced defect generation rate, saturated defect density (Nsat) and the change of defect density in the light-induced saturated state(ΔNsat) have been studied. Annealable defect density was varied by depositing samples at various substrate temperatures or by post-growth anneals of samples grown at low substrate temperatures. It is found that the generation rate, N satand ΔNsat are well correlated with ΔNann. In particular, the ΔNsat is found to follow a relation ΔNsat ≈ ΔNann. These results suggest that defect-related microscopic models are appropriate for light-induced metastability.

Reduction of the Defect Density in a-Si:H Deposited at ≤250°C

1993 ◽  
Vol 297 ◽  
Author(s):  
Hitoshi Nishio ◽  
Gautam Ganguly ◽  
Akihisa Matsuda
Keyword(s):  
Diffusion Coefficient ◽  
Amorphous Silicon ◽  
Surface Diffusion ◽  
Film Growth ◽  
Defect Density ◽  
Hydrogenated Amorphous Silicon ◽  
Device Fabrication ◽  
Surface Diffusion Coefficient ◽  
Hydrogenated Amorphous ◽  
Substrate Temperatures

We present a method to reduce the defect density in hydrogenated amorphous silicon (a-Si:H) deposited at low substrate temperatures similar to those used for device fabrication . Film-growth precursors are energized by a heated mesh to enhance their surface diffusion coefficient and this enables them to saturate more surface dangling bonds.

Saturation behavior of the Light-Induced Defect Density in Hydrogenated Amorphous Silicon

1990 ◽  
Vol 192 ◽  
Author(s):  
H. R. Park ◽  
J. Z. Liu ◽  
P. Roca i Cabarrocas ◽  
A. Maruyama ◽  
M. Isomura ◽  
...  
Keyword(s):  
Amorphous Silicon ◽  
Room Temperature ◽  
Urbach Energy ◽  
Defect Density ◽  
Generation Rate ◽  
Carrier Generation ◽  
Defect Generation ◽  
Ion Laser ◽  
Hydrogenated Amorphous ◽  
Defect Densities

ABSTRACTUsing a Kr ion laser (λ = 647.1 nm) to produce a carrier generation rate G of 3 × 1020 cm−3s−1, we have saturated the light-induced defect generation in hydrogenated (and fluorinated) amorphous silicon (a-Si:H(F)), within a few hours near room temperature. While the defect generation rate scales roughly with 1/G2, the saturation defect densities Ns,sat are essentially independent of G. The saturation is not due to thermal annealing. We have further measured Ns,sat m 37 a-Si:H(F) films grown in six different reactors under different conditions. The results show that Ns,sat lies between 5 × 1016 and 2 × 1017 cm−3, that Ns,sat drops with decreasing optical gap and hydrogen content, and that Ns,sat is not correlated with the initial defect density or with the Urbach energy.

A Defect Density of ∼ 1014 cm-3 in Hydrogenated Amorphous Silicon Deposited at High Substrate Temperatures

1992 ◽  
Vol 258 ◽  
Author(s):  
Gautam Ganguly ◽  
Akihisa Matsuda
Keyword(s):  
Substrate Temperature ◽  
Amorphous Silicon ◽  
Deposition Rate ◽  
Defect Density ◽  
Hydrogenated Amorphous Silicon ◽  
High Substrate ◽  
Surface Mobility ◽  
Surface Hydrogen ◽  
Hydrogenated Amorphous ◽  
Substrate Temperatures

ABSTRACTThe idea of surface mobility of growth precursors determined material quality has been exploited by raising the substrate temperature above the conventional 250°C and the ensuing thermal depletion of the surface hydrogen coverage compensated by increasing the precursor flux (deposition rate) to prepare ultra low defect density hydrogenated amorphous silicon.

scholarly journals Numerical Design of Ultrathin Hydrogenated Amorphous Silicon-Based Solar Cell

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
F. X. Abomo Abega ◽  
A. Teyou Ngoupo ◽  
J. M. B. Ndjaka
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Amorphous Silicon ◽  
Buffer Layer ◽  
Defect Density ◽  
Hydrogenated Amorphous Silicon ◽  
Theoretical Work ◽  
Silicon Based ◽  
The Impact ◽  
Hydrogenated Amorphous

Numerical modelling is used to confirm experimental and theoretical work. The aim of this work is to present how to simulate ultrathin hydrogenated amorphous silicon- (a-Si:H-) based solar cells with a ITO BRL in their architectures. The results obtained in this study come from SCAPS-1D software. In the first step, the comparison between the J-V characteristics of simulation and experiment of the ultrathin a-Si:H-based solar cell is in agreement. Secondly, to explore the impact of certain properties of the solar cell, investigations focus on the study of the influence of the intrinsic layer and the buffer layer/absorber interface on the electrical parameters ( J SC , V OC , FF, and η ). The increase of the intrinsic layer thickness improves performance, while the bulk defect density of the intrinsic layer and the surface defect density of the buffer layer/ i -(a-Si:H) interface, respectively, in the ranges [109 cm-3, 1015 cm-3] and [1010 cm-2, 5 × 10 13  cm-2], do not affect the performance of the ultrathin a-Si:H-based solar cell. Analysis also shows that with approximately 1 μm thickness of the intrinsic layer, the optimum conversion efficiency is 12.71% ( J SC = 18.95   mA · c m − 2 , V OC = 0.973   V , and FF = 68.95 % ). This work presents a contribution to improving the performance of a-Si-based solar cells.

Improved Light Soaking Stability of R.F. Sputter Deposited Amorphous Silicon

1991 ◽  
Vol 219 ◽  
Author(s):  
A. Wynveen ◽  
J. Fan ◽  
J. Kakalios ◽  
J. Shinar
Keyword(s):  
Amorphous Silicon ◽  
Hydrogen Content ◽  
Defect Density ◽  
Hydrogenated Amorphous Silicon ◽  
Dark Conductivity ◽  
Initial Defect ◽  
Optical Gap ◽  
Sputter Deposited ◽  
Staebler Wronski Effect ◽  
Hydrogenated Amorphous

ABSTRACTStudies of r.f. sputter deposited hydrogenated amorphous silicon (a-Si:H) find that the light induced decrease in the dark conductivity and photoconductivity (the Staebler-Wronski effect) is reduced when the r.f. power used during deposition is increased. The slower Staebler-Wronski effect is not due to an increase in the initial defect density in the high r.f. power samples, but may result from either the lower hydrogen content or the smaller optical gap found in these films.

Effects of Intermittent Deposition on the Defect Density in a-Si:H

1994 ◽  
Vol 336 ◽  
Author(s):  
Toshihiro Kamei ◽  
Nobuhiro Hata ◽  
Akihisa Matsuda
Keyword(s):  
Waiting Time ◽  
Defect Density ◽  
Hydrogenated Amorphous Silicon ◽  
Hydrogen Desorption ◽  
Growth Surface ◽  
Dangling Bond ◽  
Monolayer Growth ◽  
Hydrogenated Amorphous ◽  
Substrate Temperatures ◽  
Mechanical Shutter

ABSTRACTEffects of intermittent deposition on the defect density in hydrogenated Amorphous silicon (a-Si:H) are investigated at various substrate temperatures by using a mechanical shutter, while maintaining the discharge continuously. The intermittent deposition experiments, where monolayer growth and intermission (waiting time) are repeated in cycles, enable us to study surface dangling bond (DB) recombination and thermal hydrogen desorption separately from other reactions on the growth surface. The defect density in films prepared at lower substrate temperatures decreases with the waiting time, while that deposited at higher substrate temperatures increases with the waiting time.

scholarly journals Integration of Expanding Thermal Plasma deposited Hydrogenated Amorphous Silicon in Solar Cells

2002 ◽  
Vol 715 ◽  
Author(s):  
B.A. Korevaar ◽  
C. Smit ◽  
A.M.H.N. Petit ◽  
R.A.C.M.M. van Swaaij ◽  
M.C.M. van de Sanden
Keyword(s):  
Amorphous Silicon ◽  
Buffer Layer ◽  
Thermal Plasma ◽  
Growth Rates ◽  
Fill Factor ◽  
Defect Density ◽  
Hydrogenated Amorphous Silicon ◽  
Temperature Limit ◽  
Cell Efficiency ◽  
Hydrogenated Amorphous

AbstractA cascaded arc expanding thermal plasma is used to deposit intrinsic hydrogenated amorphous silicon at growth rates between 0.2 and 3 nm/s. Incorporation into a single junction p-i-n solar cell resulted in an initial efficiency of 6.7%, whereas all the optical and initial electrical properties of the individual layers are comparable with RF-PECVD deposited films. In this cell the intrinsic layer was deposited at 0.85 nm/s and at a deposition temperature of 250°C, which is the temperature limit for growing the p-i-n sequence. The cell efficiency is limited by the fill factor and using a buffer layer at the p-i interface deposited with RF-PECVD at low growth rate can increase this. The increase in fill factor is a result of a lower initial defect density near the p-i interface then obtained with the expanding thermal plasma, resulting in better charge carrier collection. To use larger growth rates, while maintaining the material properties, higher deposition temperatures are required. Higher deposition temperatures result in a smaller optical bandgap for the intrinsic layer and deterioration of the p-type layer, resulting in a lower opencircuit voltage. First results on applying a buffer layer will also be presented.

Sign in / Sign up

Export Citation Format

Share Document