scholarly journals Magnetic field assisted melt–spinning Nd-Fe-B ribbons and anisotropic bonded NdFeB magnets prepared thereof

2016 ◽  
Vol 26 (1) ◽  
pp. 59
Author(s):  
Nguyen Xuan Truong ◽  
Nguyen Van Vuong
Keyword(s):  
Magnetic Field ◽  
Magnetic Properties ◽  
High Temperature ◽  
Melt Spinning ◽  
Milling Process ◽  
Mixed Powder ◽  
Energy Product ◽  
Hot Compaction ◽  
The Magnetic Field ◽  
Microstructure And Magnetic Properties

The magnetic-field-assisted melt-spinning (FAMS) Nd10.5Fe72Co11B6.5 ribbons were spun in an external magnetic field of 3 kG. The prepared ribbons were ball-milled in xylene solvent for 30 minutes followed by adding in and mixing with the high-temperature binder HTB-1 (3 wt%) for further 10 minutes. The mixed powder was dried and in-mold aligned in a magnetic field of 18 kOe and hot-compacted at 200 oC. The parameters of the FAMS ribbon preparation, ball-milling process, hot-compaction and anisotropic bonded magnets’ fabrication were optimized leading to the magnet’s energy product (BH)max of 10 MGOe. The microstructure and magnetic properties of prepared ribbons and bonded magnets will be discussed in details.

Effect of Dysprosium Content on the Magnetic Properties of Nanocrystalline (Pr0.25Nd0.75)10-xDyxFe82Co2B6 Alloys

2014 ◽  
Vol 789 ◽  
pp. 28-31 ◽  
Author(s):  
He Wei Ding ◽  
Chun Xiang Cui ◽  
Ji Bing Sun
Keyword(s):  
Magnetic Properties ◽  
Melt Spinning ◽  
Maximum Energy ◽  
Vibrating Sample Magnetometer ◽  
X Ray ◽  
Maximum Energy Product ◽  
Energy Product ◽  
Intrinsic Coercivity ◽  
Electronic Microscope ◽  
Microstructure And Magnetic Properties

(Pr0.25Nd0.75)10-xDyxFe82Co2B6(x=0~0.3) ribbons were prepared by melt spinning at 25m/s and subsequent annealing. The effect of Dy content on the microstructure and magnetic properties of the ribbons has been investigated by X-ray diffractometer (XRD), scanning electronic microscope (SEM) and vibrating sample magnetometer (VSM). The magnetic properties related to the Dy content were characterized. Intrinsic coercivity of 598kA/m, remanence of 0.58T, and the maximum energy product (BH)max of 43kJ/m3 were achieved in (Pr0.25Nd0.75)9.8Dy0.2Fe82Co2B6 after annealing at 700°C for 10 minutes.

scholarly journals The Effect of External Magnetic Field on Microstructure and Magnetic Properties of Melt-Spun Nd-Fe-B/Fe-Co Nanocomposite Ribbons

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Xuan Truong Nguyen ◽  
Hong Ky Vu ◽  
Hung Manh Do ◽  
Van Khanh Nguyen ◽  
Van Vuong Nguyen
Keyword(s):  
Magnetic Field ◽  
Grain Size ◽  
High Performance ◽  
Melt Spinning ◽  
Nominal Composition ◽  
Energy Product ◽  
Melt Spun ◽  
Spinning Process ◽  
Reduction Effect ◽  
Microstructure And Magnetic Properties

The ribbons Nd2Fe14B/Fe-Co were prepared with the nominal composition Nd16Fe76B8/40% wt. Fe65Co35by the conventional and the developed magnetic field-assisted melt-spinning (MFMS) techniques. Both ribbons are nanocomposites with the smooth single-phase-like magnetization loops. The 0.32 T magnetic field perpendicular to the wheel surface and assisting the melt-spinning process reduces the grain size inside the ribbon, increases the texture of the ribbon, improves the exchange coupling, and, in sequence, increases the energy product(BH)maxof the isotropic powdered samples of MFMS ribbon in ~9% by comparison with that of the ribbon melt-spun conventionally. The grain size reduction effect caused by the assisted magnetic field has also been described quantitatively. The MFMS technique seems to be promising for producing high-performance nanocomposite ribbons.

The activation energy U(T,B) in high temperature superconductor

2020 ◽  
Vol 92 (2) ◽  
pp. 20601
Author(s):  
Abdelaziz Labrag ◽  
Mustapha Bghour ◽  
Ahmed Abou El Hassan ◽  
Habiba El Hamidi ◽  
Ahmed Taoufik ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Activation Energy ◽  
Phase Diagram ◽  
High Temperature ◽  
Apparent Activation Energy ◽  
High Temperature Superconductor ◽  
Flux Flow ◽  
Resistivity Measurements ◽  
Vortex Phase ◽  
The Magnetic Field

It is reported in this paper on the thermally assisted flux flow in epitaxial YBa2Cu3O7-δ deposited by Laser ablation method on the SrTiO3 substrate. The resistivity measurements ρ (T, B) of the sample under various values of the magnetic field up to 14T in directions B∥ab-plane and B∥c-axis with a dc weak transport current density were investigated in order to determine the activation energy and then understand the vortex dynamic phenomena and therefore deduce the vortex phase diagram of this material. The apparent activation energy U0 (B) calculated using an Arrhenius relation. The measured results of the resistivity were then adjusted to the modified thermally assisted flux flow model in order to account for the temperature-field dependence of the activation energy U (T, B). The obtained values from the thermally assisted activation energy, exhibit a behavior similar to the one showed with the Arrhenius model, albeit larger than the apparent activation energy with ∼1.5 order on magnitude for both cases of the magnetic field directions. The vortex glass model was also used to obtain the vortex-glass transition temperature from the linear fitting of [d ln ρ/dT ] −1 plots. In the course of this work thanks to the resistivity measurements the upper critical magnetic field Hc2 (T), the irreversibility line Hirr (T) and the crossover field HCrossOver (T) were located. These three parameters allowed us to establish a phase diagram of the studied material where limits of each vortex phase are sketched in order to optimize its applicability as a practical high temperature superconductor used for diverse purposes.

Effect of melt-spinning speed on the microstructure and magnetic properties of Al–Cu–Fe alloy-doped SmCo5 ribbons

2021 ◽  
Vol 127 (3) ◽  
Author(s):  
Li-Zhu Wang ◽  
Shu Wang ◽  
Zhi-Ying Zhang ◽  
Hong-Wei Wang ◽  
Ji-Bing Sun ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Melt Spinning ◽  
Spinning Speed ◽  
Microstructure And Magnetic Properties

scholarly journals Field- and Stress-Induced Magnetic Anisotropy in Nanocrystalline Fe-Based and Amorphous Co-Based Alloys

1999 ◽  
Vol 32 (1-4) ◽  
pp. 289-294
Author(s):  
V. A. Lukshina ◽  
N. V. Dmitrieva ◽  
A. P. Potapov
Keyword(s):  
Magnetic Field ◽  
Magnetic Properties ◽  
Amorphous Alloy ◽  
Magnetic Anisotropy ◽  
Thermomechanical Treatment ◽  
Nanocrystalline Alloy ◽  
Complex Effect ◽  
Induced Magnetic Anisotropy ◽  
The Magnetic Field

For nanocrystalline alloy Fe73.5Cu1Nb3Si13.5B9 thermomechanical treatment was carried out simultaneously with nanocrystallizing annealing (1) or after it (2). It was shown that a change in magnetic properties for the case 1 is essentially greater than for the case 2. Complex effect of thermomagnetic and thermomechanical treatments on magnetic properties was studied in the above-mentioned nanocrystalline alloy as well as in the amorphous alloy Fe5Co70.6Si15B9.4., During the annealings both field and stress were aligned with the long side of the specimens. It was shown that the magnetic field, AC or DC, decreases an effect of loading. Moreover, the magnetic field, AC or DC, applied after stress-annealing can destroy the magnetic anisotropy already induced under load.

Small, modular and economically attractive fusion enabled by high temperature superconductors

2019 ◽  
Vol 377 (2141) ◽  
pp. 20180354 ◽  
Author(s):  
Dennis Whyte
Keyword(s):  
Magnetic Field ◽  
High Temperature ◽  
Magnetic Fields ◽  
Current Density ◽  
High Temperature Superconductors ◽  
Fusion Energy ◽  
High Magnetic Fields ◽  
Operating Temperatures ◽  
The Magnetic Field ◽  
Game Changer

The advantages of high magnetic fields in tokamaks are reviewed, and why they are important in leading to more compact tokamaks. A brief explanation is given of what limits the magnetic field in a tokamak, and why high temperature superconductors (HTSs) are a game changer, not just because of their higher magnetic fields but also for reasons of higher current density and higher operating temperatures. An accelerated pathway to fusion energy is described, defined by the SPARC and ARC tokamak designs. This article is part of a discussion meeting issue ‘Fusion energy using tokamaks: can development be accelerated?’.

Sign in / Sign up

Export Citation Format

Share Document