Bioactivity and Surface Characteristics of Titanium Implants Following Various Surface Treatments: An In Vitro Study

2015 ◽  
Vol 41 (5) ◽  
pp. e183-e188 ◽  
Author(s):  
Aswini Kumar K ◽  
Vinaya Bhatt ◽  
Manilal Balakrishnan ◽  
Mohamed Hashem ◽  
Sajith Vellappally ◽  
...  
Keyword(s):  
Surface Treatment ◽  
Calcium Ions ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Titanium Implants ◽  
Vitro Study ◽  
Acid Etching ◽  
Implant Surface ◽  
Group A

This study compared the surface topography, hydrophilicity, and bioactivity of titanium implants after 3 different surface treatments (sandblasting and acid etching, modified sandblasting and acid etching, and thermal oxidation) with those of machined implants. One hundred indigenously manufactured threaded titanium implants were subjected to 3 methods of surface treatment. The surface roughness of the nontreated (Group A) and treated samples (Groups B through D) was evaluated with a scanning electron microscope (SEM) and profilometer. The wettability was visually examined using a colored dye solution. The calcium ions attached to the implant surface after immersing in simulated body fluid (SBF) were assessed on days 1, 2, and 7 with an atomic electron spectroscope. The data were analyzed statistically. The SBF test allowed the precipitation of a calcium phosphate layer on all surface-treated samples, as evidenced in the SEM analysis. A significantly higher amount of calcium ions and increased wettability were achieved in the thermally oxidized samples. The mean roughness was significantly lower in Group A (0.85 ± 0.07) compared to Group B (1.35 ± 0.17), Group C (1.40 ± 0.14), and Group D (1.36 ± 0.18). The observations from this in vitro study indicated that surface treatment of titanium improved the bioactivity. Moreover, results identified the implants that were sandblasted, acid etched, and then oxidized attracted more calcium ions.

scholarly journals Effect of surface treatment on the shear bond strength of a resin-based cement to porcelain

2006 ◽  
Vol 17 (4) ◽  
pp. 290-295 ◽  
Author(s):  
Marcos Paulo Nagayassu ◽  
Luciana Keiko Shintome ◽  
Eduardo Shigueyuki Uemura ◽  
José Eduardo Junho de Araújo
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Resin Cement ◽  
Vitro Study ◽  
Acid Etching ◽  
And Control

The purpose of this in vitro study was to evaluate the effect of different surface treatments on the shear bond strength of a resin-based cement to porcelain. Sixty pairs of 50% aluminous porcelain discs were fabricated. In each pair, one disc measured 6 mm in diameter X 3 mm thickness (A) and the other measured 3 mm in diameter X 3mm thickness (B). The specimens were randomly assigned to 6 groups (n=10 pairs of discs), according to the surface treatment: etching with 10% hydrofluoric acid for 2 or 4min (G1 and G2); 50-µm particle aluminum oxide sandblasting for 5 s (G3); sandblasting followed by etching for 2 or 4min (G4 and G5) and control - no treatment (G6). A silane agent was applied to the treated surface of both discs of each pair. Bistite II DC dual-cure resin cement was applied and the B discs were bonded to their respective A discs. Specimens were stored in distilled water at 37ºC for 24 h and were tested in shear strength at a crosshead speed of 2 mm/min. Means in MPa were: G1: 14.21 ± 4.68; G2: 8.92 ± 3.02; G3: 10.04 ± 2.37; G4: 12.74 ± 5.15; G5: 10.99 ± 3.35; G6: 6.09 ± 1.84. Data were compared by one-way ANOVA and Tukey's test at 5% significance level. Bond strength recorded after 2-min acid etching was significantly higher than 4-min etching (p<0.05) and control (p<0.05), but did not differ significantlyfrom sandblasting alone (p>0.05) or followed by etching for 2 or 4 min (p>0.05). Within the limitations of an in vitro study, it may be concluded that 2-min hydrofluoric acid etching produced a favorable micromechanical retention that enhanced resin cement bond strength to porcelain.

Enamel Deproteinization and Its Effect on Acid Etching: An in vitro Study

2008 ◽  
Vol 33 (1) ◽  
pp. 13-19 ◽  
Author(s):  
Roberto Espinosa ◽  
Roberto Valencia ◽  
Mario Uribe ◽  
Israel Ceja ◽  
Marc Saadia
Keyword(s):  
Phosphoric Acid ◽  
Sodium Hypochlorite ◽  
Chemical Properties ◽  
In Vitro Study ◽  
Vitro Study ◽  
Acid Etching ◽  
Etching Technique ◽  
Etching Pattern ◽  
Group A

Purpose: The goal of this in vitro study was to identify the topographical features of the enamel surface deproteinized and etched with phosphoric acid (H3PO4) compared to phosphoric acid alone. Materials and method: Ten extracted lower first and second permanent molars were polished with pumice and water, and then divided into 4 equal buccal sections having similar physical and chemical properties. The enamel surfaces of each group were subjected to the following treatments: Group A: Acid Etching with H3PO4 37% for 15 seconds. Group AH1: Sodium Hypochlorite (NaOCl) 5.25% for 30 seconds followed by Acid Etching with H3PO4 37% for 15 seconds. Group AH2 ; Sodium Hypochlorite (NaOCl) 5.25% for 60 seconds followed by Acid Etching with H3PO4 37% for 15 seconds. Results showed that group AH2 etching technique reached an area of 76.6 mm2 of the total surface, with a 71.8 mm2 (94.47%), type 1 and 2 etching pattern, followed by group AH1 with 55.9 mm2 out of 75.12 mm2 (74.1%), and finally group A with only 36.8 mm2 (48.83%) out of an area of 72.7 mm2. A significant statistical difference (P &lt;0 .05) existed between all groups, leading to the conclusion that enamel deproteinization with 5.25% NaOCl for 1 minute before H3PO4, etching increases the enamel conditioning surface as well as the quality of the etching pattern.

Shear bond strength of metal/ceramic Interface after different surface treatments: an in vitro study. Resistência ao cisalhamento da interface metal/cerâmica após diferentes tratamentos de superfície: estudo in vitro

2013 ◽  
Author(s):  
Sílvia Fontes Do Amaral Pereira
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Vitro Study ◽  
Metal Ceramic

O objetivo do presente estudo in vitro foi verificar, através de teste de cisalhamento, a resistência de união da liga Wironia®light, à base de níquel-cromo sem berílio, sujeita a diferentes tratamentos de superfície, às cerâmicas Vita VM13 e Noritake. Foram confeccionados oitenta espécimes cilíndricos metálicos, com o auxílio de uma matriz de aço, nas dimensões de 4 mm de diâmetro por 4 mm de altura. Os espécimes foram divididos em oito grupos (n=10), de acordo com o tipo de tratamento superficial aplicado à liga metálica e com o tipo de cerâmica testada. Estes foram avaliados de acordo com os critérios de resistência ao cisalhamento e, com o auxílio de microscopia óptica, foi avaliada a área de cerâmica remanescente aderida ao metal após a fratura. Os corpos-de-prova do G6 (fabricados em Cerâmica Noritake com jateamento-26,401 ± 11,637 MPa) apresentaram maior resistência ao cisalhamento (p> 0,05) enquanto que os menores valores foram registrados no G4 (Cerâmica Vita com utilização de broca-13,440 ± 7,766 MPa). G6 (19425,4 μm2) apresentou a maior área de cerâmica aderida ao metal (p> 0,05) enquanto que o G4 (2310,2 μm2) apresentou a menor área. Concluiu-se que G6 obteve os valores mais altos de resistência ao cisalhamento e de remanescente cerâmico aderido à superfície metálica enquanto que o G4 obteve os valores mais baixos. Descritores: Restaurações metalo-cerâmicas; ligas de níquel-cromo;porcelana dentária.

scholarly journals Macrophagic Inflammatory Response Next to Dental Implants with Different Macro- and Micro-Structure: An In Vitro Study

2021 ◽  
Vol 11 (12) ◽  
pp. 5324
Author(s):  
Maria Menini ◽  
Francesca Delucchi ◽  
Domenico Baldi ◽  
Francesco Pera ◽  
Francesco Bagnasco ◽  
...  
Keyword(s):  
Inflammatory Response ◽  
Dental Implants ◽  
In Vitro Study ◽  
Titanium Implants ◽  
Implant Surface ◽  
Bone Implant ◽  
Optimal Outcomes ◽  
Negative Controls ◽  
Inflammatory Effect

(1) Background: Intrinsic characteristics of the implant surface and the possible presence of endotoxins may affect the bone–implant interface and cause an inflammatory response. This study aims to evaluate the possible inflammatory response induced in vitro in macrophages in contact with five different commercially available dental implants. (2) Methods: one zirconia implant NobelPearl® (Nobel Biocare) and four titanium implants, Syra® (Sweden & Martina), Prama® (Sweden & Martina), 3iT3® (Biomet 3i) and Shard® (Mech & Human), were evaluated. After 4 h of contact of murine macrophage cells J774a.1 with the implants, the total RNA was extracted, transcribed to cDNA and the gene expression of the macrophages was evaluated by quantitative PCR (qPCR) in relation to the following genes: GAPDH, YWHAZ, IL1β, IL6, TNFα, NOS2, MMP-9, MMP-8 and TIMP3. The results were statistically analyzed and compared with negative controls. (3) Results: No implant triggered a significant inflammatory response in macrophages, although 3iT3 exhibited a slight pro-inflammatory effect compared to other samples. (4) Conclusions: All the samples showed optimal outcomes without any inflammatory stimulus on the examined macrophagic cells.

Potential neurotoxicity of titanium implants: Prospective, in-vivo and in-vitro study

Biomaterials ◽  
2021 ◽  
pp. 121039
Author(s):  
Shahar Shelly ◽  
Sigal Liraz Zaltsman ◽  
Ofir Ben-Gal ◽  
Avraham Dayan ◽  
Ithamar Ganmore ◽  
...  
Keyword(s):  
In Vitro Study ◽  
Titanium Implants ◽  
Vitro Study
Sign in / Sign up

Export Citation Format

Share Document