The Effect of Sugar Content for the Wettability of Superhydrophobic Aluminum Substrate

A chemical etching technique is used to prepare a superhydrophobic surface with a honeycomb rough structure on the aluminum surface. Use SEM, Optical contact angle meter and Surface tension detector to characterize the etched aluminum substrate. After the 8th etching, the surface of the sample showed the morphology of micro/nano-scale honeycomb pores and protrusions, and the water contact angle (WCA) is 135°. After being modified with octadecanethiol methanol solution, WCA is 153.1°. After modification, the contact angle of the sample surface decreases with the increase of the glucose solution concentration. When the glucose solution concentration reaches 1000 mg/L, the superhydrophobicity is lost.

Second Iteration of Slotted Fractal Log Periodic Dipole Antenna for UHF Digital TV Band Application

This paper discusses the simulations and measurements of the antenna with and without slot implementation in terms of reflection coefficient (S11) and radiation pattern. The slot implementation on each of the radiating elements on the 2nd iteration log periodic fractal Koch antenna (LPFKA) was described in this paper. This method is utilised to reduce the antenna's size while also preventing the lower designated frequencies from shifting to the higher band as the iteration increases. The antenna is designed to test and observe performance in the Ultra High Frequency (UHF) band, which ranges from 0.5 GHz to 3.0 GHz. Computer Simulation Technology (CST) software is used to design and model the antenna, which was then built using the wet etching technique. The antenna's substrate is made of FR-4 laminated board with a dielectric constant of 4.6, tangent loss of 0.019, and a thickness of 1.6mm. The results demonstrate good agreement, with a steady radiation pattern over the operational bandwidth and a reflection coefficient of less than -10 dB for the frequency range of interest. The antenna is being tested with Digital TV decoder and the result is observed towards the picture of the Digital TV.

Fabrication of a Chalcogenide Glass Microlens Array for Infrared Laser Beam Homogenization

Infrared (IR) microlens arrays (MLA) have attracted increasing interest for use in infrared micro-optical devices and systems. However, the beam homogenization of IR laser light is relatively difficult to achieve because most materials absorb strongly in the IR wavelength band. In this paper, we present a new method for the application of double-sided quasi-periodic chalcogenide glass (ChG) MLAs to infrared laser homogenization systems. These are non-regular arrays of closely spaced MLAs. The double-sided MLAs were successfully prepared on the ChG surface using a single-pulse femtosecond laser-assisted chemical etching technique and a precision glass molding technique. More than two million close-packed microlenses on the ChG surface were successfully fabricated within 200 min. By taking advantage of ChG’s good optical performance and transmittance (60%) in the infrared wavelength band (1~11μm), the homogenization of the IR beam was successfully achieved using the ChG quasi-periodic MLA.

Novel Approach to Synthesize Nanostructured Gallium Oxide for Devices Operating in Harsh Environmental Conditions

The importance of Ga2O3-based material for harsh environmental applications has attracted the interest of researchers in exploring various fabrication and growth techniques of Ga2O3-based nanomaterials using effective and low-cost processes. Herein, a demonstration to improve the wettability of liquid gallium on a rough silicon surface is presented. To control the roughness process, the silicon surface was patterned and groove-shape structures on the silicon were created using a photoelectrochemical (PEC) etching technique. Gallium oxide nanostructures were grown by thermal oxidation from liquid Ga in the presence and the absence of a silver thin film used as a catalyst. Scanning Electron Microscopy (SEM) was used to observe the morphology of the nanostructures grown on the roughed surface of the silicon substrate. The conformal deposition of Ga2O3 nanostructures inside the grooves of the PEC etched silicon surface was observed. The presence of Ag catalyst was found to completely change the morphology of Ga2O3. This method is recommended for the sustainable and low-cost synthesis of nanostructured gallium oxide for applications, including gas sensing.

The Effect of Etching Time On Structural Properties of Porous Quaternary AlInGaN Thin Films

Using photo electrochemical etching technique (PEC), porous silicon (PS) layers were produced on n-type silicon (Si) wafers to generate porous silicon for n-type with an orientation of (111) The results of etching time were investigated at: (5,10,15 min). X-ray diffraction experiments revealed differences between the surface of the sample sheet and the synthesized porous silicon. The largest crystal size is (30 nm) and the lowest crystal size is (28.6 nm) The analysis of Atomic Force Microscopy (AFM) and Field Emission Scanning Electron Microscope (FESEM) were used to research the morphology of porous silicon layer. As etching time increased, AFM findings showed that root mean square (RMS) of roughness and porous silicon grain size decreased and FESEM showed a homogeneous pattern and verified the formation of uniform porous silicon.