scholarly journals STUDY OF METHODS FOR IMPROVING THE PHYSICAL AND MECHANICAL PROPERTIES OF COTTON FIBER.

2019 ◽  
Vol 78 (10) ◽  
pp. 709-712
Author(s):  
Alisher Mashrabovich Salimov ◽  
◽  
Otabek Alisherovich Salimov ◽  
Keyword(s):  
Mechanical Properties ◽  
Cotton Fiber ◽  
Physical And Mechanical Properties

scholarly journals Changes of Indicators in Fiber and Cotton Seed Quality in Separating Cut Fractions on Cotton Fiber Mass

2020 ◽  
Vol 8 (6) ◽  
pp. 1245-1248
Keyword(s):  
Mechanical Properties ◽  
Cotton Fiber ◽  
Cotton Seed ◽  
Seed Quality ◽  
Physical And Mechanical Properties ◽  
High Quality ◽  
Average Mass ◽  
Mass Fractionation ◽  
Fourth Type ◽  
Modal Mass

This article describes the fourth type of medium-fiber Hampor, currently widely used in the Surkhandarya region, the lengnth is about 160-170 mg, 171-180 mg, 181-190 mg, 191-200 mg, 201-205 mg, 206-210 mg was divided into fractions by mass of fibers, the LKM equipment was cleaned of fine and dirty particles in the laboratory of the ginnery, DL-10 was isolated from the fiber on the ginning equipment, and the physical and mechanical properties of the seeds, the strength of the breakage, the modal mass, the length of the staple mass, the average mass, the ripening, the length and the squared irregularity were determined by the equipment. The optimal option for fiberglass mass fractionation was proposed to obtain high quality products.

PEMANFAATAN KAYU AKASIA MANGIUM (Acacia mangium Willd) UNTUK MEBEL

2012 ◽  
Vol 4 (1) ◽  
pp. 1
Author(s):  
Djoko Purwanto
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Physical Properties ◽  
Treatment Process ◽  
Acacia Mangium ◽  
Physical And Mechanical Properties ◽  
Wood Fibers ◽  
Test Parameters ◽  
Mechanical And Physical Properties ◽  
Scale Scores

Timber Acacia mangium (Acacia mangium, Willd) for Furniture. The study aims to determine the mechanical and physical properties and the decorative value (color and fiber) wood of acacia mangium with using finishing materials. This type of finishing material used is ultran lasur natural dof ,ultran lasur classic teak, aqua politur clear dof, aqua politur akasia dan aqua politur cherry. After finishing the wood is stored for 3 months. Test parameters were observed, namely, physical and mechanical properties of wood, adhesion of finishing materials, color and appearance of the fiber, and timber dimensions expansion. The results showed that the mechanical physical properties of acacia wood qualified SNI. 01-0608-89 about the physical and mechanical properties of wood for furniture, air dry the moisture content from 13.78 to 14.89%, flexural strength from 509.25 to 680.50 kg/cm2, and compressive strength parallel to fiber 342.1 - 412.9 kg/cm2. Finishing the treatment process using five types of finishing materials can increase the decorative value (color and fiber) wood. Before finishing the process of acacia mangium wood has the appearance of colors and fibers and less attractive (scale scores 2-3), after finishing acacia wood fibers have the appearance of colors and interesting and very interesting (scale 4-5).Keywords: mangium wood, mechanical properties, decorative value, finishing, furniture.

Physical and Mechanical Properties of Tenun Pahang Fabrics using Alternative Yarns

2016 ◽  
Vol 13 (2) ◽  
pp. 67
Author(s):  
Engku Liyana Zafirah Engku Mohd Suhaimi ◽  
Jamil Salleh ◽  
Suzaini Abd Ghani ◽  
Mohamad Faizul Yahya ◽  
Mohd Rozi Ahmad
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Silk Fabrics ◽  
Recovery Angle ◽  
Made In

An investigation on the properties of Tenun Pahang fabric performances using alternative yarns was conducted. The studies were made in order to evaluate whether the Tenun Pahang fabric could be produced economically and at the same time maintain the fabric quality. Traditional Tenun Pahang fabric uses silk for both warp and weft. For this project, two alternative yarns were used which were bamboo and modal, which were a little lower in cost compared to silk. These yarns were woven with two variations, one with the yarns as weft only while maintaining the silk warp and the other with both warp and weft using the alternative yarns. Four (4) physical testings and three (3) mechanical testings conducted on the fabric samples. The fabric samples were evaluated including weight, thickness, thread density, crease recovery angle, stiffness and drapability. The results show that modal/silk and bamboo silk fabrics are comparable in terms of stiffness and drapability, hence they have the potential to replace 100% silk Tenun Pahang.

Basic set of experiments for determination of mechanical properties of sand

2014 ◽  
Vol 62 (1) ◽  
pp. 129-137
Author(s):  
A. Sawicki ◽  
J. Mierczyński
Keyword(s):  
Mechanical Properties ◽  
Soil Mechanics ◽  
Physical And Mechanical Properties ◽  
Local Strain ◽  
Initial State ◽  
Laboratory Equipment ◽  
Additional Information ◽  
Basic Set ◽  
Initial Anisotropy

Abstract A basic set of experiments for the determination of mechanical properties of sands is described. This includes the determination of basic physical and mechanical properties, as conventionally applied in soil mechanics, as well as some additional experiments, which provide further information on mechanical properties of granular soils. These additional experiments allow for determination of steady state and instability lines, stress-strain relations for isotropic loading and pure shearing, and simple cyclic shearing tests. Unconventional oedometric experiments are also presented. Necessary laboratory equipment is described, which includes a triaxial apparatus equipped with local strain gauges, an oedometer capable of measuring lateral stresses and a simple cyclic shearing apparatus. The above experiments provide additional information on soil’s properties, which is useful in studying the following phenomena: pre-failure deformations of sand including cyclic loading compaction, pore-pressure generation and liquefaction, both static and caused by cyclic loadings, the effect of sand initial anisotropy and various instabilities. An important feature of the experiments described is that they make it possible to determine the initial state of sand, defined as either contractive or dilative. Experimental results for the “Gdynia” model sand are shown.

PREPARATION AND CHARACTERIZATION OF REPROCESSED COMPOSITES OF POLYPROPYLENE REINFORCED BY WOOD FIBERS: PHYSICAL AND MECHANICAL PROPERTIES

2017 ◽  
Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Fibers
Sign in / Sign up

Export Citation Format

Share Document