scholarly journals Current condition of the exposed concrete façades reinforcement of the Vilanova Artigas building: modern architectural heritage

2021 ◽  
Vol 14 (1) ◽  
Author(s):  
Adriana de Araujo ◽  
Claudia de Andrade Oliveira ◽  
Tatiana Regina da Silva Simão
Keyword(s):  
Steel Corrosion ◽  
Corrosion Products ◽  
Structural Safety ◽  
Published Data ◽  
Architectural Heritage ◽  
Electrochemical Tests ◽  
History Of ◽  
Patch Repairs ◽  
Corrosion State ◽  
Active Corrosion

abstract: The heritage of modern architecture in exposed reinforced concrete has been shown pathological manifestations affecting the structural safety and functionality of the buildings. The manifestations are, primarily, associated with the steel corrosion; however published data obtained from site surveys, on the Brazilian architectural heritage and related to the issue, are still scarce in the literature. Thus, the aim of the study is to assess the current condition of the exposed concrete façades reinforcement of the Vilanova Artigas building, a Brazilian architectural heritage, opened in 1969. Legal restrictions limited the destructive tests and sampling areas. The history of the interventions, environmental aggressiveness and preliminary inspection (in the parent concrete and patch repairs) provided qualified information for analyzing in situ testing results. In the sampling areas physical, chemical and electrochemical tests were carried out. The façades surfaces are naturally porous, irregular, with concrete segregation and corrosion products stains; 24% of the concrete was replaced with proprietary mortar repair. In patch repairs, the average carbonation depth ranged from 3 to 29 mm, in concrete it ranged from 15 to 30 mm. The reinforcement cover ranged from 8 to 33 mm. Corrosion potential maps, with equipotential lines drawn at 50 mV intervals, indicated the corrosion-prone areas, where there is a concentration of lines with a variation equal to or greater than 150 mV. The presence of corrosion products, detected in the visual examination of the reinforcement under the patch repairs, validated the active corrosion state. The rough surface of the concrete, the low cover to depassivated reinforcement and the active corrosion state emphasize the need for monitoring the façades and the urgency of implementing a preventive maintenance plan, along with a conservation project in order to preserve the heritage values of the building.

History of diatom studies in sphagnum bogs of Russia and some adjacent countries

2008 ◽  
Vol 42 ◽  
pp. 36-54
Author(s):  
M. S. Kulikovskiy
Keyword(s):  
Published Data ◽  
Sphagnum Bogs ◽  
History Of

Main trends of diatom studies in Sphagnum bogs of Russia and adjacent countries are shown. On the basis of published data, making use of modern taxonomical changes, the taxonomical list of diatoms from the considered Sphagnum bogs is presented.

Update on the Boundaries of the Curly Birch Range

2020 ◽  
pp. 9-21
Author(s):  
L.V. Vetchinnikova ◽  
◽  
A.F. Titov ◽  
◽  
Keyword(s):  
Population Size ◽  
Natural Populations ◽  
Forest Tree ◽  
Published Data ◽  
Population Approach ◽  
Key Factors ◽  
History Of ◽  
Individual Trees ◽  
Karelian Birch

The article reports on the application of the best known principles for mapping natural populations of curly (Karelian) birch Betula pendula Roth var. carelica (Mercklin) Hämet-Ahti – one of the most appealing representatives of the forest tree flora. Relying on the synthesis and analysis of the published data amassed over nearly 100 years and the data from own full-scale studies done in the past few decades almost throughout the area where curly birch has grown naturally, it is concluded that its range outlined in the middle of the 20th century and since then hardly revised is outdated. The key factors and reasons necessitating its revision are specified. Herewith it is suggested that the range is delineated using the population approach, and the key element will be the critical population size below which the population is no longer viable in the long term. This approach implies that the boundaries of the taxon range depend on the boundaries of local populations (rather than the locations of individual trees or small clumps of trees), the size of which should not be lower than the critical value, which is supposed to be around 100–500 trees for curly birch. A schematic map of the curly birch range delineated using this approach is provided. We specially address the problem of determining the minimum population size to secure genetic diversity maintenance. The advantages of the population approach to delineating the distribution range of curly birch with regard to its biological features are highlighted. The authors argue that it enables a more accurate delineation of the range; shows the natural evolutionary history of the taxon (although it is not yet officially recognized as a species) and its range; can be relatively easily updated (e.g. depending on the scope of reintroduction); should be taken into account when working on the strategy of conservation and other actions designed to maintain and regenerate this unique representative of the forest tree flora.

scholarly journals On the Short Time Scale Evolutionary History of the Contact Binary VW Cephei

1998 ◽  
Vol 11 (1) ◽  
pp. 396-396
Author(s):  
I. Pustylnik
Keyword(s):  
Evolutionary History ◽  
Light Curves ◽  
Published Data ◽  
Short Time Scale ◽  
Flare Activity ◽  
Considerable Portion ◽  
History Of ◽  
Contact Binary ◽  
Elongation Phase ◽  
Short Time

We study the short-time evolutionary history of the well-known contact binary VW Cep. Our analysis is based partly on the numerous UBV lightcurves obtained at Tartu Observatory, IUE spectra, and samples from the published data. Special attention is given to the effects of asymmetry of the light curves. A higher degree of asymmetry outside the eclipses along with the significant displacements of the brightness maxima in respect to the elongation phase is interpreted as evidence that a considerable portion of the flaring source is concentrated close to the neck connecting the components. We discuss the nature of asymmetry in terms of possible mass exchange and the flare activity and compare the results of our model computations with the record of orbital period variations over the last 60 years.

scholarly journals Experimental Analysis of Reinforcement Rust in Cement under Corrosive Environment

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 241
Author(s):  
Xiaozhen Li ◽  
Hui Wang ◽  
Jianmin Wang ◽  
Junzhe Liu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Steel Corrosion ◽  
Corrosion Products ◽  
Chloride Salt ◽  
Corrosive Environment ◽  
Cement Slurry ◽  
Passivation Film ◽  
Chloride Environment ◽  
Corrosive Environments ◽  
Structural Layer

In this work, the microstructure characteristics of corrosion products of reinforcement under a corrosive environment with chloride, carbonation and the combination of chloride-carbonization were studied by x-ray photoelectron spectroscopy (XPS) and scanning electron microscopy/energy spectroscopy (SEM-EDX). The results indicate that the outside of the passivation film reacts with the cement slurry to produce Fe–SiO4 in all three corrosive environments. The inner side is not completely corroded. The morphology of the corrosion is different in the three environments. In a chloride environment, corrosion products have obvious cracks, and the local layered structure is dense. In a carbonation environment, the surface of the steel corrosion shows a uniform granular structure and loose texture. With the combination of chloride and combination, the surface of the structural layer of steel corrosion was uneven and accompanied by protrusions, cracking and spalling occurred. The composition of the corrosion substances in the three corrosion environments are mainly composed of FeO, Fe3O4, Fe2O3 and Fe–SiO4. The content of iron oxide increases from a chloride salt, carbonization to the composite environment, indicating that the corrosion degree intensifies successively.

Leaching of Am-241 from a Radioactive Waste Glass Corroded in the Presence of Stainless Steel Corrosion Products and/or Bentonite

1987 ◽  
Vol 112 ◽  
Author(s):  
Masaki Tsukamoto ◽  
Inga-Kari Björner ◽  
Hilbert Christensen ◽  
Hans-Peter Hermansson ◽  
Lars Werme
Keyword(s):  
Stainless Steel ◽  
Radioactive Waste ◽  
Mass Loss ◽  
Total Mass ◽  
Corrosion Behaviour ◽  
Steel Corrosion ◽  
Waste Glass ◽  
Corrosion Products ◽  
Total Mass Loss ◽  
Elemental Mass

AbstractThe release of Am-241 during corrosion of the radioactive waste glass, JSS-A, has been studied in the presence of corrosion products and/or uncom-pacted bentonite. The corrosion behaviour of Am-241 has been analyzed using gamma spectrometry. Adsorption of Am-241 on bentonite is observed in all cases. The contents of Am-241 in centrifuged leachates are in most cases less than 1/100 of total values. The normalized elemental mass loss of Am increases initially with corrosion time, and the values in the presence of bentonite and corrosion products are larger than those in the presence of bentonite alone. This tendency is in agreement with results previously found for other elements. The release of Am is low, only about 10–20 % of the corresponding total mass loss.

scholarly journals On the importance of materials in the Monegros colonisation settlements

ZARCH ◽  
2019 ◽  
pp. 280-291
Author(s):  
Luis Prieto Mochales
Keyword(s):  
Single Unit ◽  
Architectural Heritage ◽  
Doctoral Thesis ◽  
Research Framework ◽  
Inherent Value ◽  
Urban Heritage ◽  
Central Elements ◽  
History Of ◽  
Materials Used

Two central elements converge in the heritage values of Spain’s colonisation settlements in general and of those in the Los Monegros region in particular: the notion of the single unit and the fusion of modernity and tradition. Materials play an important role in both aspects. This analysis seeks to identify the values in the original projects that are essential in order to recognise colonisation settlements as examples of architectural and urban heritage. The premise of this analysis is that the materials used to build these towns and villages have inherent value and, as such, must be maintained and conserved. This paper forms part of a larger research framework, a doctoral thesis currently underway, in which the present conditions, degree of conservation and causes of deterioration observed in the colonisation settlements of Los Monegros are being analysed. After a series of general reflections on the architectural heritage of the materials, and after subsequent study of their current condition of the materials, guidelines are proposed for the improvement of their conservation. A series of possible criteria are also set out that can serve as a guide for any interventions to be made to the architectural heritage of these settlements, which are part of the overall history of Spain’s agrarian colonisation project.

scholarly journals Evidence for independent domestication of sheep mtDNA lineage A in India and introduction of lineage B through Arabian sea route

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ranganathan Kamalakkannan ◽  
Satish Kumar ◽  
Karippadakam Bhavana ◽  
Vandana R. Prabhu ◽  
Carolina Barros Machado ◽  
...  
Keyword(s):  
Arabian Sea ◽  
Indian Subcontinent ◽  
Domestic Sheep ◽  
Published Data ◽  
Sheep Population ◽  
Sheep Breeds ◽  
The World ◽  
History Of ◽  
Wild Sheep ◽  
Indian Sheep

AbstractIndia ranks the second in the world in terms of its sheep population with approximately 74.26 million represented by 44 well-described breeds in addition to several non-descript populations. Genetic diversity and phylogeography of Indian sheep breeds remain poorly understood, particularly for south Indian breeds. To have a comprehensive view of the domestication history of Indian sheep, we sequenced the mitochondrial DNA (mtDNA) control region (D-loop) and cytochrome b gene (CYTB) of 16 Indian domestic sheep breeds, most of them (13) from the south India. We analysed these sequences along with published data of domestic and wild sheep from different countries, including India. The haplotype diversity was relatively high in Indian sheep, which were classified into the three known mtDNA lineages, namely A, B and C. Lineage A was predominant among Indian sheep whereas lineages B and C were observed at low frequencies but C was restricted to the breeds of north and east India. The median joining network showed five major expanding haplogroups of lineage A (A1–A5). Out of which, A2, A4 and A5 were more frequent in Indian sheep in contrast to breeds from other parts of the world. Among the 27 Indian sheep breeds analysed, Mandya and Sonadi breeds were significantly different from other Indian breeds in the MDS analyses. This was explained by a very high contribution of lineage B into these two breeds. The Approximate Bayesian Computation (ABC) provided evidence for the domestication of lineage A sheep in the Indian subcontinent. Contrary to the current knowledge, we also found strong support for the introduction of lineage B into Indian subcontinent through sea route rather than from the Mongolian Plateau. The neighbour-joining tree of domestic and wild sheep revealed the close genetic relationship of Indian domestic sheep with Pakistani wild sheep O. vignei blanfordi. Based on our analyses and archaeological evidences, we suggest the Indian subcontinent as one of the domestication centres of the lineage A sheep, while lineage B sheep might have arrived into India from elsewhere via Arabian sea route. To the best of our knowledge, this is the first comprehensive study on Indian sheep where we have analysed more than 740 animals belonging to 27 sheep breeds raised in various regions of India. Our study provides insight into the understanding of the origin and migratory history of Indian sheep.

scholarly journals XANES-Based Determination of Redox Potentials Imposed by Steel Corrosion Products in Cement-Based Media

2018 ◽  
Author(s):  
Bin Ma ◽  
Alejandro Fernandez-Martinez ◽  
Benoît Madé ◽  
Nathaniel Findling ◽  
Ekaterina Markelova ◽  
...  
Keyword(s):  
Steel Corrosion ◽  
Corrosion Products ◽  
Redox Potentials

A study of the corrosion of polymethyl methacrylate coated rebar using glancing angle X-ray absorption near edge spectroscopy

CORROSION ◽  
10.5006/3912 ◽  
2021 ◽  
Author(s):  
Arthur Situm ◽  
Xiaoxuan Guo ◽  
Burke Barlow ◽  
Bao Guo ◽  
Ian Burgess ◽  
...  
Keyword(s):  
Polymethyl Methacrylate ◽  
Polymer Coating ◽  
Steel Corrosion ◽  
Corrosion Products ◽  
Thin Layers ◽  
Fluorescence Signal ◽  
X Rays ◽  
X Ray ◽  
Glancing Angle ◽  
X Ray Absorption

Polymer coatings can be used to mitigate the corrosion of steel in high chloride environments. Obtaining speciation information from thin corrosion layers can be important for understanding corrosion mechanisms, including polymer coating failure. This study outlines the effectiveness of collecting glancing angle X-ray absorption near edge spectroscopy (GA-XANES) spectra at the Fe K-edge to obtain chemical speciation information at the polymer-steel interface without removal of the polymer film. The depth of penetration of the incident X-rays can be altered by changing the incidence angle, allowing for more fluorescence signal from corrosion products to be detected relative to the Fe metal fluorescence signal in GA-XANES spectra. This study demonstrates the use of GA-XANES to study thin layers of steel corrosion and obtain depth profile information of steel corrosion products beneath a polymethyl methacrylate polymer coating.

Sign in / Sign up

Export Citation Format

Share Document