LIQUID SPRAY PENETRATION MEASUREMENTS USING HIGH-SPEED BACKLIGHT ILLUMINATION IMAGING IN A SMALL-BORE COMPRESSION IGNITION ENGINE

2020 ◽  
Vol 30 (5) ◽  
pp. 371-387
Author(s):  
Yilong Zhang ◽  
S. Meng ◽  
Sanghoon Kook ◽  
K. S. Kim ◽  
C.-B. Kweon
Keyword(s):  
High Speed ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Spray Penetration ◽  
Liquid Spray

The Compression-Ignition Engine and Its Applicability to British Railway Traction

1933 ◽  
Vol 124 (1) ◽  
pp. 3-61 ◽  
Author(s):  
L. F. R. Fell
Keyword(s):  
Internal Combustion Engine ◽  
High Speed ◽  
Combustion Engine ◽  
Internal Combustion ◽  
High Rate ◽  
Wide Field ◽  
Compression Ignition ◽  
Electric Locomotive ◽  
Compression Ignition Engine ◽  
Railway Traction

The author considers that, while the internal combustion engine is not universally applicable to British railway traction, there is a wide field which can be more economically covered by the oil engine than by other means. Electric transmission is, in spite of high first cost, the most readily adaptable for use in conjunction with the oil engine, and possesses a balance of advantages over all other known systems. The oil-electric locomotive offers a long list of important advantages for railway operation not possessed by other systems. These advantages are, however, offset by high first cost for powers of 1,000 b.h.p. and over. A comparison is drawn between the first cost of steam and oil-electric locomotives for the various duties called for in the service of a British railway. This shows that, while the first cost of the oil-electric main line express passenger locomotive is three times that of the existing steam locomotive, the first costs of branch passenger, medium goods, and shunting steam and oil-electric engines are comparable. This is owing to the cost per brake horse-power required diminishing with increase of size in the case of the steam locomotive, whereas it remains constant in the case of the oil-electric. Owing to the high rate of acceleration necessary the use of the oil-electric system is considered unsuitable as a substitute for dependent electrification of suburban lines. The railway oil engine is a specialized requirement. It must be of the high-speed type running at speeds of up to 1,500 r.p.m., in order to reduce first cost and for other reasons. Details are given of various types of British compression-ignition engines which are considered suitable for British railway work. The author deduces that an engine of twelve-cylinder “V” type and an engine with six cylinders in line, both incorporating the same design and size of cylinder, would fill all the requirements which can be economically met by the oil engine on a British railway. He selects the single sleeve-valve engine design as having the greatest balance of advantages in its favour for railway purposes. Attention is drawn to the importance of simplifying the installation of the compression-ignition engine and various suggestions are put forward to this end. In conclusion the author stresses the importance of the railway companies giving a lead to the internal combustion engine industry as to the railway requirements in size and type of engine, and states that it is the purpose of his paper to assist those concerned in arriving at this immediately important decision.

scholarly journals Experimental Research on Controllability and Emissions of Jet-Controlled Compression Ignition Engine

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2936 ◽  
Author(s):  
Hua Tian ◽  
Jingchen Cui ◽  
Tianhao Yang ◽  
Yao Fu ◽  
Jiangping Tian ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
High Speed ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Emissions ◽  
Spark Timing ◽  
Crank Angle ◽  
Marine Engines ◽  
Si Engines ◽  
Ci Engines

Low-temperature combustions (LTCs), such as homogeneous charge compression ignition (HCCI), could achieve high thermal efficiency and low engine emissions by combining the advantages of spark-ignited (SI) engines and compression-ignited (CI) engines. Robust control of the ignition timing, however, still remains a hurdle to practical use. A novel technology of jet-controlled compression ignition (JCCI) was proposed to solve the issue. JCCI combustion phasing was controlled by hot jet formed from pre-chamber spark-ignited combustion. Experiments were done on a modified high-speed marine engine for JCCI characteristics research. The JCCI principle was verified by operating the engine individually in the mode of JCCI and in the mode of no pre-chamber jet under low- and medium-load working conditions. Effects of pre-chamber spark timing and intake charge temperature on JCCI process were tested. It was proven that the combustion phasing of the JCCI engine was closely related to the pre-chamber spark timing. A 20 °C temperature change of intake charge only caused a 2° crank angle change of the start of combustion. Extremely low nitrogen oxides (NOx) emission was achieved by JCCI combustion while keeping high thermal efficiency. The JCCI could be a promising technology for dual-fuel marine engines.

Some Problems Connected with High-Speed Compression-Ignition Engine Development

1932 ◽  
Vol 36 (261) ◽  
pp. 733-787 ◽  
Author(s):  
C. B. Dicksee
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Injection System ◽  
Fuel Injection System ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Development

In this paper the author does not propose to deal with any particular form or type of engine or fuel-injection system, but to discuss some of the problems which are encountered when engaged on the development of a high-speed compression-ignition engine.The main problems to be solved consist in devising suitable means for utilising to the fullest possible extent the oxygen available within the cylinder and for avoiding the production of smoke and noise and, in so far as it is connected with combustion conditions, smell.

Parametric Study of Ignition and Combustion Characteristics From a Gasoline Compression Ignition Engine Using Two Different Reactivity Fuels

2016 ◽  
Author(s):  
Khanh Cung ◽  
Toby Rockstroh ◽  
Stephen Ciatti ◽  
William Cannella ◽  
S. Scott Goldsborough
Keyword(s):  
High Speed ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Injection Timing ◽  
Strong Impact ◽  
Boost Pressure ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Ignition And Combustion

Unlike homogeneous charge compression ignition (HCCI) that has the complexity in controlling the start of combustion event, partially premixed combustion (PPC) provides the flexibility of defining the ignition timing and combustion phasing with respect to the time of injection. In PPC, the stratification of the charge can be influenced by a variety of methods such as number of injections (single or multiple injections), injection pressure, injection timing (early to near TDC injection), intake boost pressure, or combination of several factors. The current study investigates the effect of these factors when testing two gasoline-like fuels of different reactivity (defined by Research Octane Number or RON) in a 1.9-L inline 4-cylinder diesel engine. From the collection of engine data, a full factorial analysis was created in order to identify the factors that most influence the outcomes such as the location of ignition, combustion phasing, combustion stability, and emissions. Furthermore, the interaction effect of combinations of two factors or more was discussed with the implication of fuel reactivity under current operating conditions. The analysis was done at both low (1000 RPM) and high speed (2000 RPM). It was found that the boost pressure and air/fuel ratio have strong impact on ignition and combustion phasing. Finally, injection-timing sweeps were conducted whereby the ignition (CA10) of the two fuels with significantly different reactivity were matched by controlling the boost pressure while maintaining a constant lambda (air/fuel equivalence ratio).

scholarly journals Simulation of Combustion Process of Diesel and Ethanol Fuel in Reactivity Controlled Compression Ignition Engine

CFD letters ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 1-11
Author(s):  
Fatin Farhanah Zulkurnai ◽  
Wan Mohd Faizal Wan Mahmood ◽  
Norhidayah Mat Taib ◽  
Mohd Radzi Abu Mansor
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Combustion Process ◽  
Good Control ◽  
Injection Timing ◽  
Compression Ignition ◽  
Low Carbon ◽  
Compression Ignition Engine ◽  
Reactivity Controlled Compression Ignition ◽  
Complete Combustion

Reactivity controlled compression ignition (RCCI) engine give advantages over conventional diesel engine with the promising engine power and good control on NOx and soot emission. The trend of the RCCI concept is still new and Is very important to control the ignition in order to control the combustion progress and emission. The objective of this study is to provide data on the combustion characteristics and emission of diesel as high reactive, and ethanol as the low reactive fuel in the RCCI engine. The engine speed and injection timing were varied. Simulation work was conducted by using the Converge CFD software based on the Yanmar TF90 diesel engine parameter. Results show that operating the engine at low speed resulting in better engine performance and low carbon emissions due to the sufficient oxygen contents. For the high-speed engine, advancing the injection timing improves the fuel and air reactivity and steeper the equivalence ratio gradient, which result in a complete combustion process.

Some Problems Connected with High-Speed Compression-Ignition Engine Development

1931 ◽  
Vol 26 (2) ◽  
pp. 309-382
Author(s):  
C. B. Dicksee
Keyword(s):  
High Speed ◽  
Chemical Engineering ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
North East ◽  
The North ◽  
Individual Character ◽  
Scientific Institutions ◽  
Marine Engineers ◽  
Engine Development

This paper was read by Mr. Dicksee on the occasion of the second Joint iMeeting of eleven Scientific Institutions, as follows:— The Chemical Engineering Group, the Diesel Engine Users' Association, the Institute of Fuel, the Institute of Marine Engineers, the Institution of Automobile Engineers, the Institution of Mechanical Engineers, the Institution of Petroleum Technologists, the Junior Institution of Engineers, the North-East Coast Institution of Engineers and Shipbuilders, the Royal Aeronautical Society, and the Society of Engineers. Following last year's precedent, the Chair was taken by Mr. Tookey, President of the Institution of Automobile Engineers, who introduced Mr. A. E. L. Chorlton as Chairman for the meeting. Mr. Chorlton gave it as his opinion that meetings of this nature must be exceedingly valuable as a means of expressing to the nation a combined technical opinion which must have far more weight than an expression of more individual character. He suggested that a continuation of the practice might lead to the formation of something in the nature of a Technical Parliament, and asked those present to consider the possibility of some such result. Mr. Chorlton went on to emphasize the importance of research for all classes of mechanical engineering, laying special stress on the need for co-ordination of research among all parties.

Side Effect of Production of Biodiesel from Jatropha Seed Oil: A Case Study in Thailand

2014 ◽  
Vol 1051 ◽  
pp. 326-332 ◽  
Author(s):  
Kanokon Rodjanakid ◽  
Chinda Charoenphonphanich ◽  
Teerapatr Srinorakutara
Keyword(s):  
High Speed ◽  
Seed Oil ◽  
Diesel Oil ◽  
Department Of Energy ◽  
Wear Scar ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blends ◽  
Jatropha Seed ◽  
Lubricating Properties

The objective of this research is to produce biodiesel from the jatropha seed oil and compare its lubricating properties to other types of fuel used in a compression ignition engine. The optimum mixture is also investigated. The produced biodiesel is tested to determine its identity and purity. The result showed that its purity is 98.38%, which is higher than 96.5% as specified by the standard of Department of Energy Business. The resulting biodiesel is tested in a compression ignition engine, including as an additive to stabilize the ethanol in diesel oil. The four types of fuel blends are; diesohol with a proportion of diesel : ethanol : biodiesel D95E5B5 by volume, pure biodiesel from jatropha seed oil, biodiesel with low proportion D95B5, and a standard diesel oil. The test results of physical properties of the four types of fuel show that all meets the standard of high speed diesel oil, except the flash point property of the diesohol. To compare the lubricating properties, each type of the fuel has been tested with the High Frequency Reciprocating Rig (HFRR) according the CEC-F-06-A-96 standard. The results showed that the pure biodiesel from jatropha seed oil, biodiesel D95B5 and diesohol D95E5B5 have the wear scar 169 μm, 204 μm, and 205 μm respectively. The wear scar of each type of the studied fuels is below the allowable standard wear scar 460 μm.

Sign in / Sign up

Export Citation Format

Share Document