2012 ◽  
Vol 9 (1) ◽  
pp. 131-135
Author(s):  
M.A. Pakhomov

The paper presents the results of modeling the dynamics of flow, friction and heat transfer in a descending gas-liquid flow in the pipe. The mathematical model is based on the use of the Eulerian description for both phases. The effect of a change in the degree of dispersion of the gas phase at the input, flow rate, initial liquid temperature and its friction and heat transfer rate in a two-phase flow. Addition of the gas phase causes an increase in heat transfer and friction on the wall, and these effects become more noticeable with increasing gas content and bubble diameter.


1972 ◽  
Vol 51 (1) ◽  
pp. 97-118 ◽  
Author(s):  
O. M. Phillips

A theory is developed to describe the evolution of the entrainment interface in turbulent flow, in which the surface is convoluted by the large-scale eddies of the motion and at the same time advances relative to the fluid as a result of the micro-scale entrainment process. A pseudo-Lagrangian description of the process indicates that the interface is characterized by the appearance of ‘billows’ of negative curvature, over which surface area is, on average, being generated, separated by re-entrant wedges (lines of very large positive curvature) where surface area is consumed. An alternative Eulerian description allows calculation of the development of the interfacial configuration when the velocity field is prescribed. Several examples are considered in which the prescribed velocity field in the z direction is of the general form w = Wf(x – Ut), where the maximum value of the function f is unity. These indicate the importance of leading points on the surface which are such that small disturbances in the vicinity will move away from the point in all directions. The necessary and sufficient condition for the existence of one or more leading points on the surface is that U [les ] V, the speed of advance of an element of the surface relative to the fluid element at the same point. The existence of leading points is accompanied by the appearance of line discontinuities in the surface slope re-entrant wedges, In these circumstances, the overall speed of advance of the convoluted surface is found to be W + (V2 – U2)½, where W is the maximum outwards velocity in the region; this result is independent of the distribution f.When the speed U with which an ‘eddy’ moves relative to the outside fluid is greater than the speed of advance V of an element of the front, the interface develops neither leading points nor discontinuities in slope; the amplitude of the surface convolutions and the overall entrainment speed are both reduced greatly. In a turbulent flow, therefore, the large-scale motions influencing entrainment are primarily those that move slowly relative to the outside fluid (with relative speed less than V). The experimental results of Kovasznay, Kibens & Blackwelder (1970) are reviewed in the light of these conclusions. It appears that in their experiments the entrainment speed V is of the order fifteen times the Kolmogorov velocity, the large constant of proportionality being apparently the result of augmentation by micro-convolutions of the interface associated with small and meso-scale eddies of the turbulence.


2018 ◽  
Vol 59 (1) ◽  
pp. 75-91 ◽  
Author(s):  
Yuki Sato ◽  
Kazuhiro Izui ◽  
Takayuki Yamada ◽  
Shinji Nishiwaki ◽  
Makoto Ito ◽  
...  

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1804
Author(s):  
Cesar A. Sciammarella ◽  
Federico M. Sciammarella ◽  
Luciano Lamberti

Macroscopic behavior of materials depends on interactions of atoms and molecules at nanometer/sub-nanometer scale. Experimental mechanics (EM) can be used for assessing relationships between the macro world and the atomic realm. Theoretical models developed at nanometric and sub-nanometric scales may be verified using EM techniques with the final goal of deriving comprehensive but manageable models. Recently, the authors have carried out studies on EM determination of displacements and their derivatives at the macro and microscopic scales. Here, these techniques were applied to the analysis of high-resolution transmission electron microscopy patterns of a crystalline array containing dislocations. Utilizing atomic positions as carriers of information and comparing undeformed and deformed configurations of observed area, displacements and their derivatives, as well as stresses, have been obtained in the Eulerian description of deformed crystal. Two approaches are introduced. The first establishes an analogy between the basic crystalline structure and a 120° strain gage rosette. The other relies on the fact that, if displacement information along three directions is available, it is possible to reconstruct the displacement field; all necessary equations are provided in the paper. Remarkably, the validity of the Cauchy-Born conjecture is proven to be correct within the range of observed deformations.


2014 ◽  
Vol 624 ◽  
pp. 213-217 ◽  
Author(s):  
Tomas Návrat ◽  
Jindrich Petruška

The paper deals with numerical analysis of the process of roller straightening of rails. The problem of repeated elasto-plastic bending is solved by a program in MATLAB based on FEM algorithm with Eulerian description of material flow through the straightening machine. Beam element formulation with a shear deformation effect is used for the rail discretization. The results are compared with literature and standard FE analysis with Lagrangian description of material flow. Effectiveness of presented formulation is discussed and its applicability for fast iterative optimization of the straightening process is illustrated.


2016 ◽  
Vol 21 (1) ◽  
pp. 83-94 ◽  
Author(s):  
Imre Ferenc Barna ◽  
Gabriella Bognar ◽  
Krisztian Hriczo

We investigate Navier-Stokes (NS) and the continuity equations in Cartesian coordinates and Eulerian description for the two dimensional incompressible nonNewtonian fluids. Due to the non-Newtonian viscosity we consider the Ladyzenskaya model with a non-linear velocity dependent stress tensor. The key idea is the multidimensional generalization of the well-known self-similar Ansatz, which has already been used for non-compressible and compressible viscous flow studies. Geometrical interpretations of the trial function are also discussed. Our recent results are compared to the former Newtonian ones.


Author(s):  
Giuseppe Pennisi ◽  
Olivier Bauchau

Abstract Dynamics of axially moving continua, such as beams, cables and strings, can be modeled by use of an Arbitrary La-grangian Eulerian (ALE) approach. Within a Finite Element framework, an ALE element is indeed a non-material system, i.e. a mass flow occurs at its boundaries. This article presents the dynamic description of such systems and highlights the peculiarities that arise when applying standard mechanical principles to non-material systems. Starting from D’Alembert’s principle, Hamilton’s principle and Lagrange’s equations for a non-material system are derived and the significance of the additional transport terms discussed. Subsequently, the numerical example of a length-changing beam is illustrated. Energetic considerations show the complex dynamic behavior non-material systems might exhibit.


Sign in / Sign up

Export Citation Format

Share Document